========================================================================= Date: Tue, 31 Jul 2001 23:03:25 -0500 Reply-To: Curtis Cameron Sender: HPLX Mailing List From: Curtis Cameron Organization: None Subject: Re: Weird dbcheck errors Comments: To: Theodore Heise In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit On Tue, 31 Jul 2001 12:38:40 -0500 Theodore Heise wrote: >Yesterday I got error messages for four of my seven databases about >non-contiguous blocks. I set about trying to clean up the databases. > >I ran dbcheck with the /d switch and found no errors. I then ran >it without the /d switch and again found no errors. Can I ask if when it reported errors, you had tried to check several data files at a time? I had found that there was some memory allocation problems that might cause false negatives if it's already checked several databases in the same run. To know for sure, run DBCHECK with only one file to check. I've been working on a new version to reduce the memory needed, and it might address this problem if that's indeed what it is. -- Curtis Cameron WGS-84 N33.033 W96.724 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 31 Jul 2001 23:17:10 -0500 Reply-To: melancon@microgear.net Sender: HPLX Mailing List From: Mike Melancon Subject: Sundisk SD-10 flash cards MIME-Version: 1.0 Content-type: text/plain; charset=US-ASCII Content-transfer-encoding: 7BIT Does anyone know if these cards Sundisk model SD-10 will work in the 100LX and 200LX. Mike ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 1 Aug 2001 14:16:05 +0200 Reply-To: gonter+usenet@wu-wien.ac.at Sender: HPLX Mailing List From: Gerhard Gonter Subject: Re: Who is Beverly Carvalho? MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Barry wrote: > I suspect that it was a ruse of some sort to get me to open a > virus email. But since it did contain appropriate quotes from > this list I doubt if it was automated. But who knows. There are viruses that extract random information off private documents and web caches etc. Sircam even distributes your private documents to random strangers whose addresses were extracted e.g. from web caches. > I always leave email protection running but auto-protect turned > off. But now that's changed. Good idea. +gg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 1 Aug 2001 07:29:50 -0600 Reply-To: "Feldman, Robert" Sender: HPLX Mailing List From: "Feldman, Robert" Subject: Re: Sundisk SD-10 flash cards Comments: To: "melancon@microgear.net" MIME-Version: 1.0 Content-Type: text/plain The models Sandisk said will work are the SDP (will not work in the 95LX), SDP5, SDPL5, and SDP5A series. They state that the SD series will not work, as they are are not PCMCIA compatable. -----Original Message----- From: Mike Melancon Ýmailto:melancon@microgear.net¨ Sent: Tuesday, July 31, 2001 11:17 PM To: HPLX-L@UCONNVM.UCONN.EDU Subject: Sundisk SD-10 flash cards Does anyone know if these cards Sundisk model SD-10 will work in the 100LX and 200LX. Mike ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 1 Aug 2001 08:37:16 -0500 Reply-To: Theodore Heise Sender: HPLX Mailing List From: Theodore Heise Subject: Re: Weird dbcheck errors In-Reply-To: <5nvemtkat450tvpii4kmqv5ph9653tektr@4ax.com> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Tue, 31 Jul 2001, Curtis Cameron wrote: > Can I ask if when it reported errors, you had tried to check several > data files at a time? Yes indeed. I routinely run "dbcheck \_dat\*.?db" to check all seven of my databases at one time. Each time I've seen the sporadic error message has been when batching. Ted -- Theodore Heise West Lafayette, IN, USA ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 1 Aug 2001 08:47:21 -0500 Reply-To: Theodore Heise Sender: HPLX Mailing List From: Theodore Heise Subject: Re: Hotmail In-Reply-To: <20010801032014.UMQW15499.mtiwmhc22.worldnet.att.net@yahoo.com> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Wed, 1 Aug 2001, Larry Castor wrote: > Werner, > > > > I do check the email of my wife as well, but I use another > >trick. If she gets an Email (which is not often) I am notified > >by GMX about the arrival of the email with a SMS (pager > >service), but it could as . . .< > > No, I don't think Hotmail has a sms, but it does have forwarding-so > maybe I could just forward any of her mail to another account that I > can access. Thanks for the idea. Here's another idea for you. With Verizon wireless I can set up a filter to send an SMS to my StarTAC ST7868W phone anytime an e-mail arrives. It even shows up to 160 (?) characters of the Subject: header on the phone. If you have access to something like this, you could set her Hotmail account to forward to your wireless account. Ted -- Theodore Heise West Lafayette, IN, USA ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 1 Aug 2001 09:04:03 -0500 Reply-To: Theodore Heise Sender: HPLX Mailing List From: Theodore Heise Subject: Re: Driver for a DS ? In-Reply-To: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Tue, 31 Jul 2001, loic wrote: > Does somebody know where I could download the driver for a 200-LX DS. I am > out of town on a business trip, and my LX crashed very badly today and I > lost all my C drive content... of course I don't have the driver on my flash > card ! Thanks ! If you're a customer of Times2Tech, you can have one e-mailed from this link: http://www.times2tech.com/drivers.html You should be able to get one from Thaddeus, if you got your upgrade through them. Ted -- Theodore W. Heise West Lafayette, IN, USA ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 1 Aug 2001 18:27:31 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: ROBOWEB/LX MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Tony, if explicit paths have to be set, but relative paths or paths without drive letter shall be given, maybe the "truename" command of DOS can help here? Or, since truename cannot store its output in a variable, hwich is probably needed then, the batch extender strings.com has a parameter "truename" which does the same as "truename" under DOS, but stores the output in an environment variable. I don't know if the config files can somehow use environment variables, but if they can, the problem might be solved with strings.com. GTX daniel On Wed, 1 Aug 2001 11:36:39 +1200, Tony Hutchins wrote: > Stefan, me again, sorry - there is one exception I think. For > HV to find a file outside the directory where HV.EXE is, the > file must have a fully explicit path. So, for viewing an HTML > attachment in POST/LX, with HV, the TmpDir in POST.CFG should > be c:\tmp rather than \tmp or .\tmp. I, unfortunately > generalised this to all directories. Oh, yes and as > ROBOWEB/LX uses HV for reading offline, the HTML links also > need to be fully explicit - so I'd better still check HTMDir > and OtherDir .. or just leave it up to the user. It's freeware > after all :) > -- Daniel.Hertrich@gmx.de phone: +49 177 7955549 Celia.Hertrich@gmx.de phone: +49 177 8616031 fax & voice mail: +49 721 151399479 http://www.daniel-hertrich.de ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 1 Aug 2001 15:38:14 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: ROBOOWEB/LX Missing sr.bat MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable In RWOUTBOX it is mentioned to have a line PostOnline=3Dsr.bat under ÝSYSTEM¨. But where is sr.bat ? I can't find it in my copies of roboweb. Have I to create it? Uli ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 1 Aug 2001 17:23:48 -0500 Reply-To: Thomas Rundel Sender: HPLX Mailing List From: Thomas Rundel Subject: Re: Tranderferring/Converting HP200LX Phonebook/Appointment to HP,Jornada 548, how??? Any utility for this??? Comments: To: "Robbert J. van Herksen" MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Robbert, synching a 200LX with a Jornada can be done, but is a two step process which involves a desktop PC and Microsoft Outlook: - First use Curtis Cameron's excellent OL2LX software to synchronize the 200LX contacts and appointments with Outlook. - Then use ActiveSync to synchronize Outlook with any Windows CE machine. Tom www.rundel.net/palmtop On Tue, 24 Jul 2001 09:41:59 +0200, "Robbert J. van Herksen" wrote: > Hi there, > > I still use my HP200LX every day, but have one HP Jornada, and I want = to > transfer/translate my Phonebook and Appointments to the Jornada 548 = Pocket > PC. > > Anyone having experience with this?? > > Thanks for your help!! > > Robbert > Soesterberg, Netherlands > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- Dipl.-Inform. Thomas Rundel Rundel Datentechnik, Rappenstr. 20, 73033 Goeppingen, Germany Phone +49-7161-156870, Fax +49-7161-1568711, www.rundel.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 11:34:13 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: ROBOOWEB/LX Missing sr.bat MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Thu, 2 Aug 2001 08:22:54 +1200 (NZT) Uli, it is written by ROBOWEB, and re-written each time ROBOWEB runs. - Tony 44m40s ago ... On Wed, 1 Aug 2001 15:38:14 -0400, Ulrich Allen wrote: > In RWOUTBOX it is mentioned to have a line PostOnline=sr.bat > under ÝSYSTEM¨. But where is sr.bat ? I can't find it > in my copies of roboweb. Have I to create it? Uli > > ** HPLX-L LIST Info at > http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 12:40:20 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: ROBOWEB/LX MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Thu, 2 Aug 2001 08:30:17 +1200 (NZT) Daniel, I do really like the strings.com you mention. I have .bat files for many applications in my DOS path, so applications run well from anywhere, from the command line. They all look like this: c:\bin\strings.com xxx=truename %1 a:\hv\hv %xxx% set xxx= Daniel! Yup it works on directories too - even with a trailing "\" ! I think this would work, for RWEBDIR.SCR. Doesn't even need strings.com (it is hard to get an environment variable back into a script). I started writing this thinking I may be able to use strings.com, but it seems old "truename" will do. Just copy everything between the "-------" into a new RWEBDIR.SCR. I even tested it. It displays a ">" during startup each time it finds it had to modify a directory. --------------- = ~dirval $a1 = it $a1 t upper = a1 $it if (= 0) fin if (= none) fin if (!= ) dstart = it .\\ :dstart ; Daniel Hertrich 1-Aug-2001 ! truename $it > truename.xxx file r truename.xxx get get file c if (= $a1) trails e > :trails = ~dirval $it if (!found \\) dadd = at $it t beginning \\ = bt $it = it #at t decap #bt if (= \\) fin :dadd = ~dirval #~dirval\\ :fin = it #~dirval if (found :) ok = error $a2=$a1 has no drive: Ýexamine truename.xxx¨ x :ok ----------------- Daniel - many thanks! The bonus is everybody has "truename", and it simplifies the docs, and I don't have to think about the different directories! :) Any more ideas like this stroke of genius are greatly appreciated - you found the total solution. However, at POST/LX level, if someone has a relative directory for TmpDir, then to launch a file in HV they will need a .bat file that uses strings.com. I think I used to do this, till I discovered an explicit TmpDir does the trick. So, for the docs, I insisted on that. Simpler. If folk get HTML with ROBOWEB/LX then they will always be doing CTRL-M on a "msg.htm" using POST/LX v3.x. After this though, reading a downloaded tree of HTML with HV will be fine. - Tony 04h02m46s ago ... On Wed, 1 Aug 2001 18:27:31 +0200, Daniel Hertrich wrote: > I don't know if the config files can somehow use environment > variables, but if they can, the problem might be solved > with strings.com. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 08:37:11 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: Tranderferring/Converting HP200LX Phonebook/Appointment to,HP,Jornada 548, how??? Any utility for this??? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit > - First use Curtis Cameron's excellent OL2LX software to synchronize > the 200LX contacts and appointments with Outlook. Does OL2LX work on a german hp200lx? Kind regards Helmuth ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 05:18:56 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: Re: ROBOOWEB/LX Missing sr.bat MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Thanks Helmuth, my main problem was an old version of robot. Only the new version does the trick with roboweb. Uli > Ulrich, > > > In RWOUTBOX it is mentioned to have a line PostOnline=3Dsr.bat > > under ÝSYSTEM¨. > > But where is sr.bat ? > > I can't find it in my copies of roboweb. > > Have I to create it? > > No you don't have to. It is created by roboweb/lx. > > Kind regards > > Helmuth > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 10:36:43 +0100 Reply-To: chris@AMLOG.DEMON.CO.UK Sender: HPLX Mailing List From: Chris Randle Subject: Re: Derive for DOS stopped working! MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Message for David Goldstrom: David, Did you get your Derive working? I've got a DOS version (4.11) now, so if you want to compare a directory listing, contact me off-list: chris@amlog.co.uk -- Chris Randle ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 10:30:27 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Good News:Dropping Flash Memory prices In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit "The current glut seemed like an impossibility last year when a shortage of flash memory drove up prices to nearly $2 per megabyte. By the end of this year, however, flash memory research firm Web-Feet Research expects prices to fall to 30 cents per megabyte from the current 40 cents per megabyte" http://dailynews.yahoo.com/h/zd/20010802/tc/free-falling_flash_lifts_mp3_players_1.html Le'see... ... 225MB Sandisk card*.3=$67.50 .... pretty darn good. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 18:45:06 +0100 Reply-To: hpstaber@COMPUSERVE.COM Sender: HPLX Mailing List From: HP Staber Subject: Re: SMS Question MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Stefan Peichl wrote: > > The palmtop-mobile phone connectiong is only for ease of typing > and handling SMS. It does not mean at all, that there is a > transition from GSM to the Internet concerning SMS. But it is > handy to use the same interface for email and SMS, because > both are very similar. POST/LX is prepared for this use. Some cellphone providers (upon demand) crosslink their SMS service with their e-mail service. E.g. when I receive an SMS a copy is sent to the POP3 mailbox and I will get the same message downloaded on my next online run. This is not very important. The other way round is more convenient : when I get an e-mail sent to that account a copy with info about sender, subject and the first 160 characters of the body are copied into an SMS and sent to my cellphone. This way I know if something arrived in my mailbox and I have a fair idea about the contents as well. HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 13:19:54 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Better Batteries from the Guys That Brought You the RHIC* In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Dudes at Brookhaven have discovered a better NiMh cell http://www.space.com/businesstechnology/technology/space_gear-1.html * Relativistic Heavy Ion Collider (I just love that name!) ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 12:27:23 -0700 Reply-To: Bob Christopher Sender: HPLX Mailing List From: Bob Christopher Subject: Zip File Transfer Help Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: 8bit I am trying to get Zip.com to work between my laptop and my 200LX. I went through the zip.doc file thoroughly, but still have a few quirks. My Toshiba 2400 (486/50) laptop defaults to 2400,N,8,1 for the COM1 parameters. I used Zipset.com to establish that both the laptop and the LX are using the same port parameters. I set the LX as the serVer and attempt to back up the LX to the laptop using the laptop as the client. Some files transfer, some just hang up the system. Is anyone using Zip.com for daily backups of their LX, or have some familiarity with Zip.com? Thanks. Bob Bob Christopher Littleton, Colorado USA bob@palmtop.com HP 200-LX Palmtop = DOS Were The Days = ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 13:12:48 -0600 Reply-To: "Batson, Dale N" Sender: HPLX Mailing List From: "Batson, Dale N" Subject: 200LX Manual in PDF ? MIME-version: 1.0 Content-type: text/plain; charset=iso-8859-1 Content-transfer-encoding: 7BIT I recall downloading a PDF version of the 200LX manual several months ago, but I lost it in a hard disk crash. Does anyone know of a (free) source for this document? TIA, Dale Batson ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 13:21:36 -0600 Reply-To: "Batson, Dale N" Sender: HPLX Mailing List From: "Batson, Dale N" Subject: Re: Zip File Transfer Help MIME-version: 1.0 Content-type: text/plain; charset=iso-8859-1 Content-transfer-encoding: 7BIT Bob, I don't use ZIP every day, but I've had great success with this program. One thing I noticed the other day was it wouldn't transfer a file named "@mtn_mad.txt", but it would after I renamed it "mtn_mad.txt". I love this program and I'm surprised there's so little mention of it here. I can back up 96MB from my 200LX in under 3 hours using ZIP. Which reminds me, I need to register and support this fine program... Dale Batson -----Original Message----- From: Bob Christopher Ýmailto:bob@PALMTOP.COM¨ Sent: Thursday, August 02, 2001 1:27 PM To: HPLX-L@UCONNVM.UCONN.EDU Subject: Zip File Transfer Help I am trying to get Zip.com to work between my laptop and my 200LX. I went through the zip.doc file thoroughly, but still have a few quirks. My Toshiba 2400 (486/50) laptop defaults to 2400,N,8,1 for the COM1 parameters. I used Zipset.com to establish that both the laptop and the LX are using the same port parameters. I set the LX as the serVer and attempt to back up the LX to the laptop using the laptop as the client. Some files transfer, some just hang up the system. Is anyone using Zip.com for daily backups of their LX, or have some familiarity with Zip.com? Thanks. Bob Bob Christopher Littleton, Colorado USA bob@palmtop.com HP 200-LX Palmtop = DOS Were The Days = ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 2 Aug 2001 14:13:00 -0600 Reply-To: "Batson, Dale N" Sender: HPLX Mailing List From: "Batson, Dale N" Subject: Re: Zip File Transfer Help (backup) MIME-version: 1.0 Content-type: text/plain; charset=iso-8859-1 Content-transfer-encoding: 7BIT Here's the technique I use for backing up my 96MB palmtop: First I run a batch file on the palmtop with the command: dbcheck c:\_dat\*.?db c:\apps\database\*.?db > dbchkall.log Examine the file dbchkall.log for any database errors. Create a subdirectory cloner by editing the output of: tree /b > mkdirs.bat (tree is a 4DOS directory lister) Connect the serial cable between the palmtop and the PC. Format a Zip disk, use ZIP.COM to transfer mkdirs.bat. Create the directories on the Zip disk with mkdirs.bat. From the palmtop, run a batch file with: "zip *.* /m /s /n" (This command is repeated several times to restart the backup after encountering any inevitable glitches.) Come back after three hours and everything is backed up! Dale Batson -----Original Message----- From: Bob Christopher Ýmailto:bob@PALMTOP.COM¨ Sent: Thursday, August 02, 2001 1:27 PM To: HPLX-L@UCONNVM.UCONN.EDU Subject: Zip File Transfer Help I am trying to get Zip.com to work between my laptop and my 200LX. I went through the zip.doc file thoroughly, but still have a few quirks. My Toshiba 2400 (486/50) laptop defaults to 2400,N,8,1 for the COM1 parameters. I used Zipset.com to establish that both the laptop and the LX are using the same port parameters. I set the LX as the serVer and attempt to back up the LX to the laptop using the laptop as the client. Some files transfer, some just hang up the system. Is anyone using Zip.com for daily backups of their LX, or have some familiarity with Zip.com? Thanks. Bob Bob Christopher Littleton, Colorado USA bob@palmtop.com HP 200-LX Palmtop = DOS Were The Days = ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 03:28:07 +0000 Reply-To: castorlw@YAHOO.COM Sender: HPLX Mailing List From: Larry Castor Subject: Re: Zip File Transfer Help MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Bob > I am trying to get Zip.com to work between my laptop and my > 200LX. I went through the zip.doc file thoroughly, but still > have a few quirks. My Toshiba 2400 (486/50) laptop defaults > to 2400,N,8,1 for the COM1 parameters. I used Zipset.com to I use zip.com about every other day to backup my files to one of two = different PCs. Both are using Win98 and are basically troublefree. I = also used it with Win95 and Win3.1. It was more stable with 3.1 & 95, = but with 98 it works about 99% of the time (the other 1% it loses the = connection and I have to restart) I have a Vaio laptop that I set it up on and I cannot get any connection= to my lx. Zero, zip, nada. Don't know what the problem is but feel it = has something to do with the port emulator. Curious, though, remkey = works okay. Sorry I can't be of much help. What version of Win are you = using? I had to play around with the dos window settings in 98 to get = zip to be stable. Larry ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 06:06:26 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: 32 categories vs 16 subsets in GDB MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit hi all, and thanks for getting my in-box at wanadoo cleaned out while waiting for the MM/LX ver 2, i have been 'experimenting' creating databases during night shifts where noone was run over by a truck or came in sick as a dog Ýg¨, finding that the 16 subsets in GDB are inadequate because of 32 categories plus other DB combinations from data windows. The only way to 'solve' this drawback is to copy the file under a different name and create different subsets. Smartclip then synchs the two files. Any other way? and Owen Samuelson ably wrote: >Look at all the money HP lost just from me, for not carrying on >this line with their own upgrades. isn't there anyone from HP Co. on this list we can cry on his/her shoulder? (or hurling abuse at for failing to continue making shirt-pocket sized computers) ?!? Nathalie taking care of her LX200 like a Ming China vase ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 06:45:32 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: OT: English Lesson MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, I need advice from an English speaking person! Someone told me that it is wrong to combine an "if" with a "would" in a conditional sentence. That's correct, AFAIK. But if one says, e.g. "if you would like to eat an egg, please tell me so" isn't that correct, because "would like" is a combined expression, where "would" cannot be replaced by anythin else? The reason is that I have on my home page the sentence "if you would like to concact me, please do it by email" or similar. And someone complained. ;-) Thanks for your advice (please off list)! GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 08:10:16 +0200 Reply-To: Etienne Lemaire Sender: HPLX Mailing List From: Etienne Lemaire Subject: Re: 200LX Manual in PDF ? MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I have it- 2.87Mb- Before I send it out, any others interested? Etienne ----- Original Message ----- From: Batson, Dale N To: Sent: Thursday, August 02, 2001 09:12 PM Subject: 200LX Manual in PDF ? > I recall downloading a PDF version of the 200LX manual several months ago, > but I lost it in a hard disk crash. Does anyone know of a (free) source for > this document? > > TIA, > Dale Batson > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 09:56:30 +0200 Reply-To: Malcolm Shewan Sender: HPLX Mailing List From: Malcolm Shewan Subject: Re: CIS access in France and Switzerland In-Reply-To: <200107291510.LAA15600@spdmraab.compuserve.com> Mime-version: 1.0 Content-type: text/plain; charset="US-ASCII" Content-transfer-encoding: 7bit on 7/29/01 17:13, Suresh Nirody at esseni@COMPUSERVE.COM wrote: > I'll be vacationing in France and Switzerland in the second half > of August. Apart from getting the CIS access numbers from GO PHONES, > is there anything else I need to do? e.g. would I need any modifications > to my www.cfg (extracts below) Anything else I need to consider? > TIA for all help, You will probably need to use a new national number (0836061319) in France BUT it requires a whole new script in order to access CIS. For my HPLX I haven't yet figured out myself how to do it because you also have to have the POP3 configuration for your CS account etc. With Werner Furlan we have fooled around quite a bit to get it to work and I think we succeeded as far as the connection to CS is concerned but I don't think my mail account is the right one to allow me to access with the HPLX. I just use my regular portable for my mail anyway. So I'm not too worried about getting it set-up. Just interested and curious to succeed. Please let me know how you get on and what solutions you find. Malcolm ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 10:17:47 +0100 Reply-To: HP Staber Sender: HPLX Mailing List From: HP Staber Subject: Re: 32 categories vs 16 subsets in GDB MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Nathalie, > > while waiting for the MM/LX ver 2, i have been 'experimenting' creating > databases during night shifts where noone was run over by a truck or = came in > sick as a dog Ýg¨, finding that the 16 subsets in GDB are inadequate = because > of 32 categories plus other DB combinations from data windows. The only = way > to 'solve' this drawback is to copy the file under a different name and > create different subsets. Smartclip then synchs the two files. Any = other > way? Export the GDB to an ASCII file by putting the subject into a single line preceded by a "+( " and the category field into a single line preceded by a "+c " such as : +( sudden infant death syndrome +c mortal Any notes go here and then use PalEdit's database, search and jump functions. I have switched completely to this way of doing things. HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 10:17:56 +0100 Reply-To: HP Staber Sender: HPLX Mailing List From: HP Staber Subject: Re: Zip File Transfer Help MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > > Bob > > > I am trying to get Zip.com to work between my laptop and my > > 200LX. I went through the zip.doc file thoroughly, but still > > have a few quirks. My Toshiba 2400 (486/50) laptop defaults > > to 2400,N,8,1 for the COM1 parameters. I used Zipset.com to > I use zip.com about every other day to backup my files to one of two > different PCs. Both are using Win98 and are basically troublefree. > I also used it with Win95 and Win3.1. It was more stable with 3.1 & 9 > 5, but with 98 it works about 99% of the time (the other 1% it loses > the connection and I have to restart) I had the following 2 difficulties both under WinME, WinNT and Win2000 : 1) a defective serial cable 2) Windows was using too many ressources or occupying the serial port so that neither ZIP nor CPACK nor Transfile200 would work. My solution was to create a multiboot environment. When I need to transfer files I boot into a DOS 6.2 system environment. HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 10:58:25 +0200 Reply-To: Alan Krempler Sender: HPLX Mailing List From: Alan Krempler Subject: new programs: QuickView 1.5, MiniDict MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit i mailed two new programs to the s.u.p.e.r. site today (i hope they will publish them soon): * version 1.5 of QuickView, now including an image viewer * a dictionary program, compatible with DICT/LX, but compact, SysMgr compliant and easy to use. cheers alan ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 11:27:02 +0000 Reply-To: Stefan.Peichl@T-ONLINE.DE Sender: HPLX Mailing List From: Stefan Peichl Subject: Re: Zip File Transfer Help Comments: To: Bob Christopher MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Bob Christopher wrote: > I am trying to get Zip.com to work between my laptop and my > 200LX. ZIP works 100% errorfree if it runs under plain DOS on both systems. This is not ZIP's fault. The operating systems WinXX (and SysMgr) fiddle with the serial port. Sometimes it works, sometimes not. Close WinXX and restart to DOS: No more problems. I do it several times a day. For transfers of one single small file I also used ZIP from a WinXX DOS box and it worked in most cases until I discovered, that an "errorfree" transmission was not errorfree. That means, the transfer seemed to work ok, but what I received on the palmtop was not identical to the desktop source. Therefore don't relay on apparently errorfree ZIP transmissions from within a DOS box! Repeat them from plain DOS. Stefan ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 05:59:51 -0500 Reply-To: Ed Keefe Sender: HPLX Mailing List From: Ed Keefe Subject: Re: 32 categories vs 16 subsets in GDB MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Nathalie Bugeaud asked about overcoming the subsets limitation in the database apps. The following two articles will tell you much about the databases in general http://www.palmtopPaper.com/PTPHTML/44/44c00027.htm http://www.palmtopPaper.com/PTPHTML/44/44c00013.htm and, in particular, the following sidebar gives _one_ way to work around the subset limitation. http://www.palmtopPaper.com/PTPHTML/44/44c00014.htm .ed. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 07:28:40 -0500 Reply-To: TomSalwasser@COMPUSERVE.COM Sender: HPLX Mailing List From: Tom Salwasser Subject: FLUFF:OT:FS:FA: Delorme Tripmate MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit Hello! I'm selling a Delorme Tripmate on eBay; the auction ends Sunday and it's at $64. Please visit the link below if interested. Thanks! http://cgi.ebay.com/aw-cgi/eBayISAPI.dll?ViewItem&item=1259308230 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 15:01:59 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: Re: CIS access in France and Switzerland In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Le Fri, 3 Aug 2001 09:56:30 +0200 Malcolm Shewan a =E9crit: > You will probably need to use a new national number (0836061319) in Franc= e If you are in Paris, or connect via a GSM phone (08xxxxx numbers from GSM are highly priced in France), it is better to use the old number : 01 41 02 03 04 > BUT it requires a whole new script in order to access CIS=2E FYI, when I used DOSPPP to connect on CIS, I used this script : ---- ABORT ERROR ABORT BUSY ABORT 'NO DIALTONE' ABORT 'NO CARRIER' ABORT RING REPORT CONNECT TIMEOUT 10 '' ATZ ECHO ON OK AT&F OK ATDT0141020304 TIMEOUT 60 CONNECT \r\n ame:--ame: cis ID:--ID: 100337,1703/go:pppconnect ssword: ************ TIMEOUT 60 PPP ---- hope this helps=2E=2E=2E Jacques=2E ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 06:16:06 -0700 Reply-To: wayne.yang@bigfoot.com Sender: HPLX Mailing List From: "Wayne E. Yang" Subject: Wireless Internet MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="0-1062209240-996844566=:20856" --0-1062209240-996844566=:20856 Content-Type: text/plain; charset=us-ascii The article clipping below prompts me to ask: what wireless services are people on this list using? And do you use a service like Ricochet or a wireless network at home? >>> Metricom to End Web-Access Service Ahead of Planned Auction of Company >>> WALL STREET JOURNAL >>> Metricom Inc., the struggling operator of Ricochet, one of the largest networks offering wireless Internet access in major cities across the nation, plans to discontinue its service ahead of a proposed auction of all its assets. --------------------------------- Do You Yahoo!? Make international calls for as low as $.04/minute with Yahoo! Messenger http://phonecard.yahoo.com/ --0-1062209240-996844566=:20856 Content-Type: text/html; charset=us-ascii

The article clipping below prompts me to ask: what wireless services are people on this list using? And do you use a service like Ricochet or a wireless network at home?

>>> Metricom to End Web-Access Service Ahead of Planned Auction of Company
>>> WALL STREET JOURNAL
>>> Metricom Inc., the struggling operator of Ricochet, one of the largest networks offering wireless Internet access in major cities across the nation, plans to discontinue its service ahead of a proposed auction of all its assets.


Do You Yahoo!?
Make international calls for as low as $.04/minute with Yahoo! Messenger
http://phonecard.yahoo.com/ --0-1062209240-996844566=:20856-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 07:49:14 -0700 Reply-To: fmc@REANIMATORS.ORG Sender: HPLX Mailing List From: Frank McConnell Subject: Re: Good News:Dropping Flash Memory prices In-Reply-To: Ed Padin's message of "Thu, 2 Aug 2001 10:30:27 -0400" MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Ed Padin wrote: > http://dailynews.yahoo.com/h/zd/20010802/tc/free-falling_flash_lifts_mp3_players_1.html > Le'see... ... 225MB Sandisk card*.3=$67.50 > .... pretty darn good. I'll say. Keep in mind that the prices quoted in that article are probably for the chips, bought in quantity by the makers of MP3 players, memory cards, and other products. Retail prices will probably be a bit higher, 'til the next price cut. In the meantime, Wednesday night at Costco I saw new 64MB Sandisk CF cards for US$43.99 + tax, which out here in Sillycon Valley means about $48. Yep, I impulse bought. Instant gratification at that price really minimized the return on shopping for a better price and/or waiting. Between the above news item and the grotesque packaging (CF card in plastic hanger package, repackaged in 12"x18" or so plastic thing that takes up even more shelf space) I'm guessing that inventory is being flushed from warehouse/channel to make room for something new. -Frank McConnell ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 12:00:44 -0400 Reply-To: "Corso, Tony" Sender: HPLX Mailing List From: "Corso, Tony" Subject: Andrea Kutzler email addr? MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----_=_NextPart_001_01C11C35.7403B910" This message is in MIME format. Since your mail reader does not understand this format, some or all of this message may not be legible. ------_=_NextPart_001_01C11C35.7403B910 Content-Type: text/plain; charset="iso-8859-1" received the error message below when trying to email Andrea Kutzler, which surprised me because it worked 13 days ago? thanks for taking the time Regards Tony ________________________________________________________________ This message could not be delivered to the following recipients: : Connected to 194.112.207.46 but sender was rejected. Remote host said: 550 This address is not allowed ------_=_NextPart_001_01C11C35.7403B910 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Andrea Kutzler email addr?

 received the error message below when trying to = email Andrea Kutzler, which surprised me because it worked 13 days = ago?

thanks for taking the time
Regards
Tony

_______________________________________________________________= _
This message could not be delivered to the following = recipients:
          &nb= sp;  
          &nb= sp;  <andrea.kutzler@derive-europe.com>:
          &nb= sp;  Connected to 194.112.207.46 but sender was rejected.
          &nb= sp;  Remote host said: 550 This address is not allowed

------_=_NextPart_001_01C11C35.7403B910-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 12:42:57 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Re: Andrea Kutzler email addr? Comments: To: "Corso, Tony" In-Reply-To: <8477395C635BD5118C1F009027AC96E32CD6B5@nycexc01.sithe.com> MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----=_NextPart_000_001D_01C11C19.D2B01600" This is a multi-part message in MIME format. ------=_NextPart_000_001D_01C11C19.D2B01600 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Andrea Kutzler email addr?Lokes like a SPAM bouncer message. Maybe your SMTP relay server has been blacklisted. -----Original Message----- From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu¨On Behalf Of Corso, Tony Sent: Friday, August 03, 2001 12:01 PM To: HPLX-L@uconnvm.uconn.edu Subject: Andrea Kutzler email addr? received the error message below when trying to email Andrea Kutzler, which surprised me because it worked 13 days ago? thanks for taking the time Regards Tony ________________________________________________________________ This message could not be delivered to the following recipients: : Connected to 194.112.207.46 but sender was rejected. Remote host said: 550 This address is not allowed ------=_NextPart_000_001D_01C11C19.D2B01600 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Andrea Kutzler email addr?
Lokes=20 like a SPAM bouncer message. Maybe your SMTP relay server has been=20 blacklisted.
 
-----Original Message-----
From: HPLX Mailing List=20 Ýmailto:HPLX-L@uconnvm.uconn.edu¨On Behalf Of Corso,=20 Tony
Sent: Friday, August 03, 2001 12:01 PM
To:=20 HPLX-L@uconnvm.uconn.edu
Subject: Andrea Kutzler email=20 addr?

 received the error message below when trying = to email=20 Andrea Kutzler, which surprised me because it worked 13 days = ago?

thanks for taking the time
Regards
Tony

________________________________________________________________= =20
This message could not be delivered to the = following=20 recipients:
          &nbs= p;  =20
          &nbs= p; =20 <andrea.kutzler@derive-europe.com>:
          &nbs= p; =20 Connected to 194.112.207.46 but sender was rejected.
          &nbs= p; =20 Remote host said: 550 This address is not allowed=20

------=_NextPart_000_001D_01C11C19.D2B01600-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 13:05:20 -0400 Reply-To: "Corso, Tony" Sender: HPLX Mailing List From: "Corso, Tony" Subject: Re: Andrea Kutzler email addr? Comments: To: Ed Padin MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----_=_NextPart_001_01C11C3E.7A096270" This message is in MIME format. Since your mail reader does not understand this format, some or all of this message may not be legible. ------_=_NextPart_001_01C11C3E.7A096270 Content-Type: text/plain; charset="iso-8859-1" would hate to think that, it is "net identity", that allows me to be tony@corso.net. I'll retry from home -----Original Message----- From: Ed Padin Ýmailto:ohdamnthathurts@yahoo.com¨ Sent: Friday, August 03, 2001 12:43 PM To: Corso, Tony; HPLX-L@uconnvm.uconn.edu Subject: RE: Andrea Kutzler email addr? Lokes like a SPAM bouncer message. Maybe your SMTP relay server has been blacklisted. -----Original Message----- From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu¨On Behalf Of Corso, Tony Sent: Friday, August 03, 2001 12:01 PM To: HPLX-L@uconnvm.uconn.edu Subject: Andrea Kutzler email addr? received the error message below when trying to email Andrea Kutzler, which surprised me because it worked 13 days ago? thanks for taking the time Regards Tony ________________________________________________________________ This message could not be delivered to the following recipients: : Connected to 194.112.207.46 but sender was rejected. Remote host said: 550 This address is not allowed ------_=_NextPart_001_01C11C3E.7A096270 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable RE: Andrea Kutzler email addr?

would hate to think that, it is "net = identity", that allows me to be tony@corso.net. I'll retry from = home


-----Original Message-----
From: Ed Padin Ýmailto:ohdamnthathurts@yahoo.c= om¨
Sent: Friday, August 03, 2001 12:43 PM
To: Corso, Tony; HPLX-L@uconnvm.uconn.edu
Subject: RE: Andrea Kutzler email addr?


Lokes like a SPAM bouncer message. Maybe your SMTP = relay server has been blacklisted.

-----Original Message-----
From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu= ¨On Behalf Of Corso, Tony
Sent: Friday, August 03, 2001 12:01 PM
To: HPLX-L@uconnvm.uconn.edu
Subject: Andrea Kutzler email addr?


 received the error message below when trying to = email Andrea Kutzler, which surprised me because it worked 13 days = ago?

thanks for taking the time
Regards
Tony
_______________________________________________________________= _
This message could not be delivered to the following = recipients:
          &nb= sp;  
          &nb= sp;  <andrea.kutzler@derive-europe.com>:
          &nb= sp;  Connected to 194.112.207.46 but sender was rejected.
          &nb= sp;  Remote host said: 550 This address is not allowed

------_=_NextPart_001_01C11C3E.7A096270-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 19:27:13 +0100 Reply-To: Michael Lennartz Sender: HPLX Mailing List From: Michael Lennartz Subject: Re: Wireless Internet In-Reply-To: <20010803131606.20952.qmail@web9601.mail.yahoo.com> Mime-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Hallo Wayne and all others, Living in Germany, I like to spend my holidays in Denmark. From Denmark I uploaded to my website and checked my accounts via mobile phone and laptop: Siemens C35i + Fujitsu/Mitac 5033 Laptop linked via serial cable. Works very fine. I test every computer and every email-program, if it is usable with the mobile phone. Win3.x/Shiva-dialer and Win9x are working. Under DOS NetTamer and POST/LX are working, Arachne not. I use the internet access from my mobile provider E-Plus (GSM 1800). It works every time in good quality. In Denmark I selected Telia DK for roaming and called the german provider (+49 177 192192). No problems. Checking the bill I learned, that I have payed just for the internet access like in Germany, _no_ roaming fee. Numbers starting with 19... in Germany are used for special purposes, and I think, programming the provider's invoices nobody had in mind to dial the own internet access number from abroad. May be, anytime they will remark it. My experiences in german language: http://www.fortunecity.com/meltingpot/bread/689 -- Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net Fax: +49 89 244 34 52 57 Wayne E. Yang schrieb am 03.08.2001: >Reply-To: wayne.yang@bigfoot.com >From: "Wayne E. Yang" >Date: Fri, 3 Aug 2001 06:16:06 -0700 >Subject: Wireless Internet >To: HPLX-L@UConnVM.UConn.Edu > > >The article clipping below prompts me to ask: what wireless >services are people on this list using? And do you use a service >like Ricochet or a wireless network at home? -- Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net Fax: +49 89 244 34 52 57 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 4 Aug 2001 00:19:55 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: A wireless activism paper. MIME-Version: 1.0 Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit If you are interested about "extreme" conditions to use our palmptops, you can see the paper I have posted on imc-wireless, a mailing list of the Independant Media Center... http://lists.indymedia.org/mailman/public/imc-wireless/2001-August/000027.html ÝDaniel, Hal, I even managed to make some references to your sites ;-) ¨ And yes, I have yet to think to post on the list messages from some _very weird_ MUPs where I go sometimes... ;-) Jacques. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 19:04:53 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Requiem for one of the greatest wireless technologies MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit "Metricom will shut down its pioneering Ricochet wireless Internet service next week because it has failed to find a buyer for the company, the company said Thursday." http://dailynews.yahoo.com/h/zd/20010803/tc/metricom_switches_off_ricochet_1 .html That's one less wireless solution known to work with the LX. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 3 Aug 2001 22:34:27 -0400 Reply-To: stan.hplx@VERIZON.NET Sender: HPLX Mailing List From: Stanley Dobrowski Subject: Re: ROBOWEB/LX MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Lasse Karlsson wrote: > The reason I had problems was because I had eliminated the drive-letter > in the path-specification in the config files in order to be able to = run from > any drive without having to change the configs I achieve this same effect with the SUBST command in DOS 5. I have a directory where I keep WWW/LX on my 32MB RAMdisk called: F:\wwwlx And I use the following command to create a fake drive letter pointing to this: SUBST W: F:\wwwlx And so I code all of the configurations for WWW/LX to the drive letter W:. If I need to move the whole deal to the A: drive (or any other place for that matter), I can just change my SUBST command to map the drive letter W: to any place I need to. And I don't have to change any config files. Stan ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 4 Aug 2001 08:43:03 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: OT: English Lesson MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, thanks a lot for all your valuable input, I have got about 10 emails from you! Great! So, I now know the sentence is grammatically correct, maybe a little awkward, but not wrong. I'll never stop to learn! GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 4 Aug 2001 13:51:04 +0200 Reply-To: Tomas Moberg Sender: HPLX Mailing List From: Tomas Moberg Subject: Viewing files on a Win machine? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable When I try to view text files from my HP on my Windows machine the text is wrong. My Swedich characters =E5=E4=F6 is not properly displayed. Is this due to the ANSI/ASCII translation? Is there a way to batch convert a lot of hp text files so that I can view them properly on Win98. I know some ways to convert single files but not how to convert them all at once. Tanks! /tomas moberg Uppsala ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 4 Aug 2001 06:49:28 -0700 Reply-To: Bob Christopher Sender: HPLX Mailing List From: Bob Christopher Subject: Days Program Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: 8bit I've tried to DL Daivd Bird's Days program from SUPER but have had no success. This program gives the seconds, minutes, days, weeks, months years, etc between two dates. Has anyone successfully DL this program? If so, could you email it to me. Thanks in advance. Bob Bob Christopher Littleton, Colorado USA bob@palmtop.com HP 200-LX Palmtop = DOS Were The Days = ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 4 Aug 2001 18:55:48 +0000 Reply-To: castorlw@YAHOO.COM Sender: HPLX Mailing List From: Larry Castor Subject: Re: Hotmail MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Werner, > that would be probably the easiest way. Are the messages after forwardin= g still on Hotmail? With GMX it is a bit complecated, you have to decide = between download and forwarding, and so I use 2 adresses: Nr one collects = all the mail and does a forward to my office and to Nr 2, which is my = private address at Gmx.< Didn't work afterall because Hotmail apparently does not support automatic= forwarding! At this stage, I think my wife should just drop Hotmail. = Every other email provider I've used has had no such problems. Larry ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 4 Aug 2001 15:59:50 -0500 Reply-To: Thomas Rundel Sender: HPLX Mailing List From: Thomas Rundel Subject: Re: Tranderferring/Converting HP200LX Phonebook/Appointment,to,HP,Jornada 548, how??? Any utility for this??? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Helmuth, > Does OL2LX work on a german hp200lx? OL2LX runs on the Windows desktop PC, not on the palmtop. I don't have a German 200LX, but I didn't find any problems with umlauts, and based on the structure of the program I'm sure that it will work fine with data files which use German field names instead of English ones. Tom www.rundel.net/palmtop ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 5 Aug 2001 12:09:04 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi - If you would like to discuss Roboweb you are welcome to send an email to: roboweb-subscribe@yahoogroups.com yahoo.com is a great place for Robo to dig, so I figure it should be a good place to talk too :) BTW they did change to site of mobile.yahoo: ------------ pg5.yahoo.com is now p6.oa.yahoo.com ROBOWEB/LX sample outbox RWEB.O needs the "pg5" changed to "p6.oa". Also RWEB1.SCR and RWEBXOUT.SCR each have one instance of pg5.yahoo.com - for the built-in weather support - I might remove this. ------------- - Tony --- begin of forwarded message --- To: roboweb@yahoogroups.com From: Tony Hutchins Date: Sun, 5 Aug 2001 11:35:47 +1200 Subject: Ýroboweb¨ Message Zero Sun, 5 Aug 2001 11:02:52 +1200 (NZT) Hi, I started this as a place to discuss ROBOWEB, so that the HPLX-L will not get cluttered. Yesterday I discovered that finance.yahoo.com now has quotes available from exchanges all round the world. What a great service! Already I have ROBOWEB taking advantage of this to produce summaries similar to the recently deceased "QUOTES" service on compuserve. For example, I have this in a POST/LX mailbox :) Symb/Name Volume Open Hi/Ask Low/Bid Last Change Update -------- ----------- -------- -------- -------- -------- -------- ------ INTL BUS MAC 3704100 107.80 110.09 107.10 108.09 -0.71 8/3 4:00PM YAHOO INC 3739000 18.49 18.51 17.71 17.87 -0.58 8/3 4:00PM SANDISK CORP 411600 24.79 25.42 24.70 25.42 +0.32 8/3 4:00PM LION NATHAN L 420892 5.300 5.320 5.300 5.300 -0.010 8/3 11:21PM AMP 34088 23.700 23.780 23.400 23.710 +0.060 8/3 11:24PM MOLEX INC 381900 35.88 35.98 34.30 35.18 -0.45 8/3 4:00PM INFINEON TECH 291700 25.47 25.64 24.93 25.40 -1.35 8/3 4:02PM DEUTSCHE TELE 596000 21.33 21.33 21.05 21.15 -0.15 8/3 4:00PM TELECOM NEW ZE 25000 17.89 17.89 17.55 17.72 -0.24 8/3 4:04PM TELECOM CO O 2601446 5.370 5.380 5.270 5.280 -0.100 8/3 11:36PM SKY NETWORK TV 16800 3.520 3.520 3.500 3.500 -0.050 8/3 11:20PM DJ INDU AVERAGE N/A 10550.01 10550.56 10433.07 10512.78 -38.40 8/3 4:03PM NZ TOP 40 CAP N/A 2064.65 2064.65 2051.15 2052.43 -12.21 8/3 12:08AM XETRA DAX INDEX N/A 0.00 0.00 0.00 5754.86 0.00 7/27 2:15PM NIKKEI 225 INDEX N/A 12336.51 12365.88 12241.27 12241.97 -157.23 8/3 2:00AM FTSE 100 INDEX N/A 5584.50 5590.20 5511.10 5547.60 -36.90 8/3 11:37AM NAS/NMS COMPSITE N/A 2079.15 2079.15 2047.62 2066.33 -21.05 8/3 5:16PM S&P 500 INDEX N/A 1219.61 1220.75 1205.31 1214.35 -6.40 8/3 4:18PM HANG SENG INDEX N/A 12487.99 12515.50 12256.78 12269.08 -197.29 8/3 4:07AM NZDUSD=X N/A N/A N/A N/A 0.417800 N/A 8/3 4:49PM EURUSD=X N/A N/A N/A N/A 0.883500 N/A 8/4 5:20AM DEUTSCHE MARK N/A 0.4507 0.4533 0.4495 0.4519 +0.0006 8/3 2:31PM FRENCH FRANC N/A 0.13438 0.13514 0.13401 0.13474 +0.00019 8/3 2:31PM JAPAN YEN N/A 0.008069 0.008107 0.008066 0.008087+0.000009 8/3 2:31PM SW FRANC N/A 0.5836 0.5875 0.5831 0.5857 +0.0011 8/3 2:31PM If anybody wants to try this let me know. Cheers, Tony ------------------------ Yahoo! Groups Sponsor ---------------------~--> Small business owners... Tell us what you think! http://us.click.yahoo.com/vO1FAB/txzCAA/ySSFAA/u2FxlB/TM ---------------------------------------------------------------------~-> To unsubscribe from this group, send an email to: roboweb-unsubscribe@yahoogroups.com Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/ --- end of forwarded message --- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 4 Aug 2001 20:44:42 -0400 Reply-To: J & F Sender: HPLX Mailing List From: J & F Subject: Is Super site down? MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I've tried to access the "super" site several times today. Get page not available. What's happening? ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 5 Aug 2001 18:22:37 +0530 Reply-To: Vivek Venugopalan Sender: HPLX Mailing List From: Vivek Venugopalan Subject: ANN:Announcing the availability of DOCHTML MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hello all I would like to Announce the availability of DOCHTML in source code form. DOCHTML provides a way to convert memo editor files into HTML files. I have hosted it on sourceforge. The URL is http://dochtml.sourceforge.net The latest version is Version 1.1 The application is available with source code under GPL. Suggestions, improvements? Please contact me at vivekv at users.sourceforge.net or vivekv at yahoo.com Best Regards Vivek _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 5 Aug 2001 16:37:05 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Wireless Internet MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Michael, On Fri, 3 Aug 2001 19:27:13 +0100, Michael Lennartz wrote: > I use the internet access from my mobile provider E-Plus (GSM 1800). > It works every time in good quality. In Denmark I selected Telia DK > for roaming and called the german provider (+49 177 192192). No > problems. Checking the bill I learned, that I have payed just for the > internet access like in Germany, _no_ roaming fee. Numbers starting > with 19... in Germany are used for special purposes, and I think, > programming the provider's invoices nobody had in mind to dial the > own internet access number from abroad. May be, anytime they will > remark it. Hey, das sind ja tolle Nachrichten! :-) Ich bin auch bei E-Plus. Mu_ ich direkt mal ausprobieren, wenn ich verreist bin! (in English, translated very sloppyly: WOW, great! I'm also an E-Plus customer. Hopefully they will not change that until I am on vacation for the next time) ;-) GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 5 Aug 2001 13:03:41 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Re: Hotmail Comments: To: castorlw@yahoo.com In-Reply-To: <20010804185547.BJSM5127.mtiwmhc25.worldnet.att.net@yahoo.com> MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I found that hotmail was pretty crappy too. There's no pop mail, no forwarding and it never saves sent mail unless you remember to check a box. I think Yahoo is the best. I've also used Excite and they're as good as yahoo but allow less storage. I use yahoo as my account for use with www/lx. Whenever I want to send something to my LX, I don't bother with switching cards and cables. I just send it to the yahoo mail and get it thex next time I hook up post/lx. I use ethernet for access so the speed is not a problem. > -----Original Message----- > From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu¨On > Behalf Of > Larry Castor > Sent: Saturday, August 04, 2001 2:56 PM > To: HPLX-L@uconnvm.uconn.edu > Subject: Re: Hotmail > > > Werner, > > > that would be probably the easiest way. Are the messages > after forwarding still on Hotmail? With GMX it is a bit > complecated, you have to decide between download and > forwarding, and so I use 2 adresses: Nr one collects all > the mail and does a forward to my office and to Nr 2, which > is my private address at Gmx.< > > Didn't work afterall because Hotmail apparently does not > support automatic forwarding! At this stage, I think my > wife should just drop Hotmail. Every other email provider > I've used has had no such problems. > > Larry > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 5 Aug 2001 21:11:52 +0200 Reply-To: furlan@gmx.net Sender: HPLX Mailing List From: "Dr. Werner Furlan" Organization: OE9FWV Subject: Re: Viewing files on a Win machine? Comments: To: Tomas Moberg MIME-Version: 1.0 Content-type: text/plain; charset=ISO-8859-1 Content-transfer-encoding: Quoted-printable hi Tomas, > When I try to view text files from my HP on my Windows machine the > text is wrong. My Swedich characters =E5=E4=F6 is not properly displayed= . Is > this due to the ANSI/ASCII translation? > yes indeed. > Is there a way to batch convert a lot of hp text files so that I can > view them properly on Win98. > > I know some ways to convert single files but not how to convert them > all at once. > There is a utility called fixtext and it can convert characters from a config file. It can of course be used in a batch file, you could define a directory and use *.* for the converter. http://users.erols.com/waynesof/bruce.htm here you find the files. servus, WErner -- Powered by Pegasus Mail - free at http://www.pmail.com Homepage: http://www.qsl.net/oe9fwv SMS: +436646340014@text.mobilkom.at ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 5 Aug 2001 17:10:08 -0500 Reply-To: Thomas Rundel Sender: HPLX Mailing List From: Thomas Rundel Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Actually, I would rather see all HP 200LX related stuff being discussed here. The volume of this list is so low that it is not necessary to remove certain topics. And I really don't want to subscribe to yet another list just for a few messages each day. Of course this is just my 2 cents - what do others think? Tom www.rundel.net/palmtop On Sun, 5 Aug 2001 12:09:04 +1200, Tony Hutchins = wrote: > Hi - If you would like to discuss Roboweb you are welcome to > send an email to: > > roboweb-subscribe@yahoogroups.com > > yahoo.com is a great place for Robo to dig, so I figure it > should be a good place to talk too :) Ýsnip¨ > - Tony > Ýsnip¨ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 5 Aug 2001 18:57:11 -0500 Reply-To: palmtop@n-link.com Sender: HPLX Mailing List From: Tim Subject: FLUFF: OT (sorta): Do ISA to PCI adapters exist? In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Hi all, This has an LX relevance, sort of. I'm "moving mother boards around" (to upgrade my main PC's CPU) and will lose access to a board that had both ISA and PCI slots in it. Is there any sort of adapter that will let you use an ISA card in a PCI slot .... I'm imagining "no," or they wouldn't have needed to make M-boards w/ both types of slots. What I'm losing access to is my *old,* SCM-Swap Box ... for those who don't know what that is, it's a PC-Card adapter that has (in this case .... there were several configurations) an ISA card w/ a PC-Card slot accessible at the back of the computer *and* ribbon cables that go to another plug-in slot you can mount in a drive bay, on the front of your computer. Alternately, does anyone know if there's a PCI adapter that would act as a controller card for the front-box? I used this box a lot in swapping out CF cards (in an adapter) w/ my LX (aha! the LX connection to this message!), and digital cameras too. The Swapbox was much more reliable than a USB adapter I have that's supposed to do the same thing (it would "go wiggy" *often* and not let me drag files over to my HDD w/o corrupting them. We all know *that's* no good!). TIA for any help! --tim ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 02:54:01 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: FLUFF: OT (sorta): Do ISA to PCI adapters exist? Comments: To: palmtop@n-link.com MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Tim wrote: > I'm "moving mother boards around" (to upgrade my main PC's CPU) and will > lose access to a board that had both ISA and PCI slots in it. Keep an old pc around to support your other old hardware. You aren't limited to a single pc. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 02:54:04 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit I agree. Cheers... Russ Thomas Rundel wrote: > Actually, I would rather see all HP 200LX related stuff being > discussed here. The volume of this list is so low that it is not > necessary to remove certain topics. And I really don't want to > subscribe to yet another list just for a few messages each day. > > Of course this is just my 2 cents - what do others think? > > On Sun, 5 Aug 2001 12:09:04 +1200, Tony Hutchins wrote: > > Hi - If you would like to discuss Roboweb you are welcome to > > send an email to: > > roboweb-subscribe@yahoogroups.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 02:54:07 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: LX GDB template for my video collection? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Does anyone have an LX database you'd care to share that I could use (or use as a starting point) to track my videos? I'm thinking of something that lists title, VHS/DVD, key actors, etc. Maybe I should include music CD, tapes, records too? I'm open to suggestions. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 07:35:26 +0100 Reply-To: Michael Lennartz Sender: HPLX Mailing List From: Michael Lennartz Subject: Re: (2) Fwd: Ýroboweb¨ Message Zero In-Reply-To: <200108052210.RAA01202@athena.host4u.net> Mime-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Thomas Rundel schrieb am 05.08.2001: >Actually, I would rather see all HP 200LX related stuff being >discussed here. The volume of this list is so low that it is not >necessary to remove certain topics. And I really don't want to >subscribe to yet another list just for a few messages each day. > Yes, I agree. -- Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net Fax: +49 89 244 34 52 57 -- Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net Fax: +49 89 244 34 52 57 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 08:51:01 +0100 Reply-To: hpstaber@COMPUSERVE.COM Sender: HPLX Mailing List From: HP Staber Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Thomas Rundel wrote: > > Actually, I would rather see all HP 200LX related stuff being > discussed here. The volume of this list is so low that it is not > necessary to remove certain topics. And I really don't want to > subscribe to yet another list just for a few messages each day. I subscribed in order to "support" Yahoo! They have great newsservice, floundering financial results and probably need to show some figures to people who want to place banner ad's (which we do not see with ROBOWEB/LX). My only concern is giving away my e-mail address. HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 19:18:08 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Mon, 6 Aug 2001 19:03:21 +1200 (NZT) 08h53m13s ago ... On Sun, 5 Aug 2001 17:10:08 -0500, Thomas Rundel wrote: > Actually, I would rather see all HP 200LX related stuff > being discussed here. Good point Tom. I started roboweb@yahoogroups.com because it will be convenient for me. I believe files can even be uploaded there, so I can easily add occasional scripts. I do belong to a couple of other yahoo groups and really like them. If you have a yahoo "ID" you can also look back at all the messages posted. I just felt Roboweb needed a "home" of his own - this will prevent him "taking over the knwon universe". > The volume of this list is so low > that it is not necessary to remove certain topics. And I > really don't want to subscribe to yet another list just > for a few messages each day. Fair enough. > Of course this is just my 2 cents - what do others think? Oh well it is just an experiment. Of course ROBOWEB can still be discussed here. The yahoo group may just be a useful resource. Time will tell. I am still working on a few enhancements, and don't want to hog this list with them - it just doesn't seem right. - Tony ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 04:27:35 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: Re: Fwd: Ýroboweb¨ Message Zero Comments: To: Thomas Rundel MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable I support Thomas' opinion. Why open another battle field. This list is in easy reach and well known to the few owners of HPLX. I too don't want to subscribe to another list. Here I get every thing concerning hplx in one run. Please leave it as it is. Uli > Actually, I would rather see all HP 200LX related stuff being > discussed here. The volume of this list is so low that it is not > necessary to remove certain topics. And I really don't want to > subscribe to yet another list just for a few messages each day. > > Of course this is just my 2 cents - what do others think? > > Tom > www.rundel.net/palmtop > > On Sun, 5 Aug 2001 12:09:04 +1200, Tony Hutchins = wrote: > > > Hi - If you would like to discuss Roboweb you are welcome to > > send an email to: > > > > roboweb-subscribe@yahoogroups.com > > > > yahoo.com is a great place for Robo to dig, so I figure it > > should be a good place to talk too :) > Ýsnip¨ > > - Tony > > > Ýsnip¨ > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 10:44:31 +0200 Reply-To: Ulrich Boche Sender: HPLX Mailing List From: Ulrich Boche Subject: Re: Viewing files on a Win machine? Comments: To: Tomas Moberg MIME-Version: 1.0 Content-type: text/plain; charset=iso-8859-1 Content-transfer-encoding: quoted-printable On Saturday, 04.08.2001 at 13:51 ZE2, Tomas Moberg wrote: > When I try to view text files from my HP on my Windows > machine the text > is wrong. My Swedich characters =E5=E4=F6 is not properly displayed. > Is this due to the ANSI/ASCII translation? > > Is there a way to batch convert a lot of hp text files so > that I can view > them properly on Win98. > > I know some ways to convert single files but not how to > convert them > all at once. > The reason for this mess is that DOS and Windows use different codepages. We have the same problem in German: Umlauts and special characters are at different code points in these codepages. There is a program called lx2win written by Paolo Custodio that can do the conversion. I assume it is on Super; if not, send me a note and I'll send you my copy. I'm usually using a little REXX program myself because programs like lx2win use different files for input and output and I like to update in place most of the time. Ulrich Boche = ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 02:06:57 -0700 Reply-To: shimon_nagar@yahoo.com Sender: HPLX Mailing List From: Shimon Nagar Subject: Pro-Lx MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Hi everyone, Is There any way I can scroll the days section so old task will be hide? Shimon Nagar __________________________________________________ Do You Yahoo!? Make international calls for as low as $.04/minute with Yahoo! Messenger http://phonecard.yahoo.com/ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 21:53:48 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Mon, 6 Aug 2001 21:03:11 +1200 (NZT) Uli, Tom and everybody - I was not asking everybody to subscribe to roboweb@yahoogroups.com. Sorry if I gave that impression. I don't think Roboweb is that popular. I am happy to withdraw my offer, if that is what you want! I don't want to wait for the votes to be counted. Do not send an email to subscribe-roboweb@yahoogroups.com! Or another listserver. That is what I now recommend :) This will make you feel much better about HLX-L :) I will indeed be very happy if nobody at all joins the roboweb list. At least I offered the choice. That was all it was. I hope this will stop this string of e-mails telling why people do not want to join another e-mail list - and that it will not start another thread on the opposite topic:) If there is a concern about something in this thread I would appreciate someone re-packaging it into another thread without reference to me or roboweb. Bye, Tony 35m36s ago ... On Mon, 6 Aug 2001 04:27:35 -0400, Ulrich Allen wrote: > I support Thomas' opinion. Why open another battle > field. This list is in easy reach and well known to the few > owners of HPLX. I too don't want to subscribe to another > list. Here I get every thing concerning hplx in one run. > Please leave it as it is. Uli ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 13:54:41 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: OT: English Lesson MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Fred I send this on the list again, because you are the third person who sais: On Mon, 6 Aug 2001 03:29:03 +0000, wrote: > Daniel, hope you don't mind (and off list) > > > thanks a lot for all your valuable input, I have got about 10 emails > > from you! Great! > > > > So, I now know the sentence is grammatically correct, maybe a little > > awkward, but not wrong. > > I could not find anything really wrong with it either. > > > I'll never stop to learn! > > BUT the above means: "I will not stop (provide time) to learn." > > What you probably mean is > > "I'll never stop learning" Meaning "you will always learn" Thank you! That is the best proof that I will indeed never stop learning! ;-) (please, if something is wrong with this or the above sentence, don't say so anymore. This could become a chain reaction). GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 13:54:43 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Viewing files on a Win machine? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Tomas, On Sat, 4 Aug 2001 13:51:04 +0200, Tomas Moberg wrote: > When I try to view text files from my HP on my Windows machine the text > is wrong. My Swedich characters edv is not properly displayed. > Is this due to the ANSI/ASCII translation? > > Is there a way to batch convert a lot of hp text files so that I can view > them properly on Win98. > > I know some ways to convert single files but not how to convert them > all at once. If you know a way to convert ONE file, it is only a batch bile with a for loop which you need to convert all files in a directory. for %%f in (*.txt) do convert.exe %%f if your program has the name convert.exe and needs the file to be converted as the only parameter. only TXT files will be converted. If you are looking for a fast and quite convenient search and replace utility, try gsar (available on http://www.daniel-hertrich.de/rexsync - gsar is not written by me) GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 13:54:44 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Tom On Sun, 5 Aug 2001 17:10:08 -0500, Thomas Rundel wrote: > Actually, I would rather see all HP 200LX related stuff being > discussed here. The volume of this list is so low that it is not > necessary to remove certain topics. And I really don't want to > subscribe to yet another list just for a few messages each day. > > Of course this is just my 2 cents - what do others think? The same! I really appreciate Tony'S efforts regarding roboweb and all the maintaining and supprort he gives. But I also don't think it is necessary to do that off this list. But we are roboweb users. Maybe non-users may think different. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 09:41:19 -0400 Reply-To: "M. Lennartz" Sender: HPLX Mailing List From: "M. Lennartz" Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Tony wrote: > I just felt Roboweb needed a "home" of his own - this will > prevent him "taking over the knwon universe". I think, there should be a website, where I can find scripts. For instance, the results from finance.yahoo.com are very interesting (your mail from Aug 5, 2001). I would like to find such examples together in one place/website. Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 09:44:09 -0500 Reply-To: Barry Sender: HPLX Mailing List From: Barry Subject: FLUFF: OT (sorta): Do ISA to PCI adapters exist? MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit Tim wrote: > I used this box a lot in swapping out CF > cards (in an adapter) w/ my LX (aha! > the LX connection to this message!), > and digital cameras too. > > The Swapbox was much more reliable > than a USB adapter I have that's supposed > to do the same thing (it would "go wiggy" > > *often* and not let me drag files over to > my HDD w/o corrupting them. > We all know *that's* no good!). I've been using the Sandisk Imagemate. It's a compact flash reader/writer that connects through USB, but it's always been perfect. In the 3 years that I've had it I've never had a problem of any kind and I use it at least once a day and often more. I use it for my laptop cards, my palmtop cards and my camera cards. I think they're only about $40 now and you can get them at Best Buy or just about anyplace that sells digital cameras. Barry ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 18:01:37 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Tony, for me it is very simple. For me the list is additional. And as far as I did understand, everybody is welcome there and if somebody else feels more comfortable to discuss roboweb related topics here, then he is welcome to do it here too. So what is all the recommendation about? I subscribed with pleasure! Kind regards Helmuth > Mon, 6 Aug 2001 19:03:21 +1200 (NZT) > > 08h53m13s ago ... > On Sun, 5 Aug 2001 17:10:08 -0500, Thomas Rundel wrote: > > > Actually, I would rather see all HP 200LX related stuff > > being discussed here. > > Good point Tom. I started roboweb@yahoogroups.com because it > will be convenient for me. I believe files can even be uploaded > there, so I can easily add occasional scripts. > > I do belong to a couple of other yahoo groups and really like > them. If you have a yahoo "ID" you can also look back at all > the messages posted. > > I just felt Roboweb needed a "home" of his own - this will > prevent him "taking over the knwon universe". > > > The volume of this list is so low > > that it is not necessary to remove certain topics. And I > > really don't want to subscribe to yet another list just > > for a few messages each day. > > Fair enough. > > > Of course this is just my 2 cents - what do others think? > > Oh well it is just an experiment. Of course ROBOWEB can still > be discussed here. The yahoo group may just be a useful > resource. Time will tell. I am still working on a few > enhancements, and don't want to hog this list with them - it > just doesn't seem right. > > - Tony > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 09:19:36 -0700 Reply-To: vivek venugopalan Sender: HPLX Mailing List From: vivek venugopalan Subject: Re: Viewing files on a Win machine? Comments: To: Ulrich Boche In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Folks My program dochtml can convert LX's memo files into HTML. I am sure your favourite Windows word processor will take the HTML file as input. Give it a try. Yes the problem is due to ANSI/ASCII translation - to be precise, teh oemToAscii API must be used. Vivek --- Ulrich Boche wrote: > On Saturday, 04.08.2001 at 13:51 ZE2, Tomas Moberg > > wrote: > > When I try to view text files from my HP on my > Windows > > machine the text > > is wrong. My Swedich characters edv is not > properly displayed. > > Is this due to the ANSI/ASCII translation? > > > > Is there a way to batch convert a lot of hp text > files so > > that I can view > > them properly on Win98. > > > > I know some ways to convert single files but not > how to > > convert them > > all at once. > > > The reason for this mess is that DOS and Windows use > different > codepages. We have the same problem in German: > Umlauts and > special characters are at different code points in > these codepages. > > There is a program called lx2win written by Paolo > Custodio that > can do the conversion. I assume it is on Super; if > not, send me > a note and I'll send you my copy. I'm usually using > a little REXX > program myself because programs like lx2win use > different > files for input and output and I like to update in > place most of the > time. > > Ulrich Boche > > ** HPLX-L LIST Info at > http://www.sp.uconn.edu/~mchem1/HPLX.shtml > __________________________________________________ Do You Yahoo!? Make international calls for as low as $.04/minute with Yahoo! Messenger http://phonecard.yahoo.com/ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 14:18:42 -0400 Reply-To: Bob Penick Sender: HPLX Mailing List From: Bob Penick Subject: Do PCMCIA to Compactflash adapters exist? MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Just had this question flash across my brain (quick trip too). Since there is not a simple USB connection for full size PCMCIA cards like the Sandisk Imagemate, could you use a Psion modem adapter to plug a PCMCIA type 2 memory card into one of the Imagemates? Right now I wish I had one to try with. Anybody know already? Thanks, bob ----- Original Message ----- From: "Barry" To: Sent: Monday, August 06, 2001 10:44 AM Subject: FLUFF: OT (sorta): Do ISA to PCI adapters exist? > I've been using the Sandisk Imagemate. It's a compact flash > reader/writer that connects through USB, but it's always been > perfect. In the 3 years that I've had it I've never had a > problem of any kind and I use it at least once a day and often > more. > > I use it for my laptop cards, my palmtop cards and my camera > cards. > > I think they're only about $40 now and you can get them at Best > Buy or just about anyplace that sells digital cameras. > > Barry > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 11:56:19 -0700 Reply-To: "Peter A. Castro" Sender: HPLX Mailing List From: "Peter A. Castro" Subject: Re: FLUFF: OT (sorta): Do ISA to PCI adapters exist? Comments: To: Tim In-Reply-To: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Sun, 5 Aug 2001, Tim wrote: > Hi all, > > This has an LX relevance, sort of. > > I'm "moving mother boards around" (to upgrade my main PC's CPU) and will > lose access to a board that had both ISA and PCI slots in it. > > Is there any sort of adapter that will let you use an ISA card in a PCI slot > .... I'm imagining "no," or they wouldn't have needed to make M-boards w/ > both types of slots. Nope. The two busses are incompatable. > What I'm losing access to is my *old,* SCM-Swap Box ... for those who don't > know what that is, it's a PC-Card adapter that has (in this case .... there > were several configurations) an ISA card w/ a PC-Card slot accessible at the > back of the computer *and* ribbon cables that go to another plug-in slot you > can mount in a drive bay, on the front of your computer. > > Alternately, does anyone know if there's a PCI adapter that would act as a > controller card for the front-box? There are controllers that are composed of a PCI card and a "floppy" sized port that you can mount in the front of your computer, like a ... floppy. I have one made by Antec (the DataChute PCMCIA Adpater). Mine's an ISA card, but I believe that they make a PCI card version too. See: http://www.antec-inc.com/product/pc_card/datachut.html > I used this box a lot in swapping out CF cards (in an adapter) w/ my LX > (aha! the LX connection to this message!), and digital cameras too. > > The Swapbox was much more reliable than a USB adapter I have that's supposed > to do the same thing (it would "go wiggy" guess> *often* and not let me drag files over to my HDD w/o corrupting > them. We all know *that's* no good!). I've had very good luck with the DataChute. I've had too many bad experiences with USB to even plug the ports into any computer I currently have anymore. > TIA for any help! > --tim -- Peter A. Castro or "Cats are just autistic Dogs" -- Dr. Tony Attwood ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 15:16:41 -0400 Reply-To: "M. Lennartz" Sender: HPLX Mailing List From: "M. Lennartz" Subject: Roboweb MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Hi, I tried to use roboweb (robot.exe version 1.8) on my laptop - didn't = work. Total crash - the harddisk is turning and turning and turning...switch off. Does this robot.exe work on LX only? Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 08:01:49 +1200 Reply-To: th@PARADISE.NET.NZ Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: Roboweb MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Tue, 7 Aug 2001 07:49:15 +1200 (NZT) Michael, to be honest I never tried roboweb on a machine other than a DS HP200LX. I can't answer your question. If you can get POST/LX running on your laptop (I hear this is possible with something like palrun) then I feel it is likely that ROBOWEB would run. He is not programmed to be a laptop kiler. Maybe someone will get him running on a laptop and tell how so others, who want to, can do it too. - Tony 32m34s ago ... On Mon, 6 Aug 2001 15:16:41 -0400, M. Lennartz wrote: > Hi, >=20 > I tried to use roboweb (robot.exe version 1.8) on my laptop > - didn't work. Total crash - the harddisk is turning and > turning and turning...switch off. >=20 > Does this robot.exe work on LX only? >=20 > Mit freundlichem Gru=DF / Regards / Saluton >=20 > Michael Lennartz > lennartz-mi@gmx.net >=20 > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml >=20 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 16:11:30 -0400 Reply-To: jofenlo@emory.edu Sender: HPLX Mailing List From: John Ofenloch Subject: GDB to Excel on Macintosh MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii; x-mac-type="54455854"; x-mac-creator="4D4F5353" Content-Transfer-Encoding: 7bit I have been lurking on this list for quite a while and have gained much appreciation for the power of my HPLX. I am stumped as to the best way to convert GDB files to a useful format in Excel on an Apple Powerbook. Any ideas would be greatly apprecitaed. Thanks. John Ofenloch ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 16:42:23 -0400 Reply-To: "M. Lennartz" Sender: HPLX Mailing List From: "M. Lennartz" Subject: Re: Roboweb MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Hi Tony, thank you for the immediate answer. My POST/LX is running on a laptop :-). Works fine. I'm waiting for a CF-adapter to put roboweb on the LX. It should come this week. Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 15:59:17 -0500 Reply-To: Theodore Heise Sender: HPLX Mailing List From: Theodore Heise Subject: Re: GDB to Excel on Macintosh In-Reply-To: <3B6EF9F2.E2B28E1D@emory.edu> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Mon, 6 Aug 2001, John Ofenloch wrote: > I have been lurking on this list for quite a while and have gained much > appreciation for the power of my HPLX. I am stumped as to the best way > to convert GDB files to a useful format in Excel on an Apple Powerbook. > Any ideas would be greatly apprecitaed. My first approach would be to create a Smart Clip (F5) that listed all the fields I wanted in the spreadsheet. I would add a delimiter (such as a comma or tab) between each field, and then save the Smart Clip. Next, I would go to File-Print and choose All Items, Custom (with the Smart Clip I just defined), and print to a file. Then, I would transfer the file to the Powerbook and use Excel's import or parse functions to load the file. Ted -- Theodore Heise West Lafayette, IN, USA ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 09:39:00 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: Roboweb MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Tue, 7 Aug 2001 09:24:43 +1200 (NZT) Michael! You got me curious. I set everything up on my old Libretto which runs Win95. I think I have some kind of virus on it at the moment - if I leave it unattended for about 5 minutes it crashes, apparently from boredom - saying "projecto" caused a fault. Maybe some wonky screensaver got in there. Anyway, I am just amazed!!!! I used cgagraph.com as the palmtop graphics emuator. Put Scripts=c:\post3\scripts in ÝSYSTEM¨ in POST.CFG. PKUNZIPED the robo scripts in c:\post3\scripts. Copied all the roboweb *.exe files to c:\post3. Copied over my plamtop RWEB.* x-box files. Put ExtProg=ROBOT -p "RWEB1 po" and went online and blow me down, it worked like the wind!!! The best part is the "GUI" of roboweb shows the shaded "Subject" or label line in GREEN :) Looks magnificent. Thanks for your challenge Michael :) So, we can say that ROBOWEB/LX has been seen to work on a laptop. Good luck with the CF-adaptor. I've been spending time lately speeding up ROBOWEB - having a new "Simple" mode which does no "keep" work, but still allows selective getting. However, you show me that the best way to speed it up is put it with a pentium :) - Tony 42m20s ago ... On Mon, 6 Aug 2001 16:42:23 -0400, M. Lennartz wrote: > Hi Tony, > > thank you for the immediate answer. > My POST/LX is running on a laptop :-). Works fine. I'm waiting for a > CF-adapter to put roboweb on the LX. It should come this week. > > Mit freundlichem Gru_ / Regards / Saluton > > Michael Lennartz > lennartz-mi@gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 15:14:37 -0700 Reply-To: zaaap@EARTHLINK.NET Sender: HPLX Mailing List From: Marc - Subject: Minimal Setup of VIEW? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Does anyone have a minimal setup of Malcolm Drury's VIEW running on their palmtop? Things are getting tight on my 6mb unit, and its not feasible to upgrade memory at this point. Thanks, ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 6 Aug 2001 21:40:36 -0500 Reply-To: theise@netins.net Sender: HPLX Mailing List From: Theodore Heise Subject: Re: Minimal Setup of VIEW? Marc - writes: > Does anyone have a minimal setup of Malcolm Drury's VIEW running on > their palmtop? Things are getting tight on my 6mb unit, and its not > feasible to upgrade memory at this point. I don't know if there are additional functions in other files, but I have just the main view.exe on my palmtop. It's 92k as is, and 44k when zipped. Ted ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 06:44:26 +0100 Reply-To: nospam.srtgray@clara.net Sender: HPLX Mailing List From: Stuart Gray Subject: Re: Do PCMCIA to Compactflash adaptors exist? MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Hi Bob, If you mean the Psion Modem adaptor that is used for Series 3c/5 type machines, then no, it won't work with memory cards. Apparently it doesn't have a full PCMCIA v2 pin connection, and will only work with modems. I'd be interested in how you thought to connect it - the connector is a flat, 15 pin PCMCIA dongle type (called Honda for some reason) which is specific to Psion machines. Also, whilst talking about Psion, just to clear up some of the hysteria surrounding the recent announcement. Psion will continue to manufacture and support the current models (Revo, Revo Plus, 5mx, 7) through 2004. They may well pick up development of new models before then, if the market improves. Psion is a big company, with four distinct branches: Digital, which handles the PDAs and Wavefinder (digital radio receiver); Dacom, which handles Modems, ISDN, USB; Teklogix, which has wireless and corporate products; plus the stake in Symbian, which writes and supports the EPOC OS, as used in the Nokia 9210. Other companies (eg Nokia) are developing for the latest version of EPOC, thus keeping the market alive. Psion hasn't gone away yet... Stuart > Date: Mon, 6 Aug 2001 14:18:42 -0400 > From: Bob Penick > Subject: Do PCMCIA to Compactflash adapters exist? > > Just had this question flash across my brain (quick trip too). > Since there is not a simple USB connection for full size PCMCIA cards like > the Sandisk Imagemate, could you use a Psion modem adapter to plug a PCMCIA > type 2 memory card into one of the Imagemates? Right now I wish I had one > to try with. Anybody know already? > Thanks, > bob ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 12:46:05 -0100 Reply-To: =?iso-8859-1?Q?Jos=E9?= Angel de Castro Barco Sender: HPLX Mailing List From: =?iso-8859-1?Q?Jos=E9?= Angel de Castro Barco Subject: Battery trouble Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: base64 SSBoYXZlIGEgSFBMWCAyMDAgd2l0aCAyIE1iIGFuZCBhIDIwIG1iIFNhbmRpc2sgZmxhc2ggY2Fy ZC4KClRoZXkgYXJlIHdvcmtlZCB3ZWxsIGR1cmluZyB5ZWFycywgYnV0LCByZWNlbnRseSBzb21l b25lIGlzIHdyb25nLgoKVGhlIHBhbG10b3Agb2Z0ZW4gc2F5cyAiYmF0dGVyeSBlcnJvciwgcHVz aCBFU0Mga2V5Ii4gSWYgdGhlIGZlZWRlciBpcyBub3QgcApnZ2VkIHRoZSBwYWxtdG9wIHN1dGhk b3duIGFuZCBwb3dlciBvZmYuCgpXaGVuIFBPV0VST04sIHRoZSBwYWxtdG9wIHJlc3RhcnQgYWdh aW4gYW5kLCBzb21ldGltZXMsIHRoZSBkYXRhIGluIHRoZSBjIGRyCmUgYXJlIGNvbXBsZXRlbHkg bG9zdC4KCkkgY2hhbmdlZCB0aGUgYmF0dGVyeSAobWFpbiBhbmQgYmFja3VwKSwgdW5wbHVnZ2Vk IHRoZSBmbGFzaCBjYXJkLCByZWluc3RhbGwKIHRoZSBzb2Z0LC4uLiB0aGUgdHJvdWJsZSBwZXJz aXN0LgoKU29tZW9uZSBjYW4gaGVscCBtZT8uIFRoYW5rcy4KCg== ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 06:54:00 -0400 Reply-To: I Al-Khars Sender: HPLX Mailing List From: I Al-Khars Subject: super carousel software Mime-Version: 1.0 Content-Type: text/plain; format=flowed Did any one try the super carousel software. I have plan to buy this software from thaddeus.com _________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 11:21:51 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Re: super carousel software In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I'm not sure about SSC but it looks like a packaged version of SC with a bunch of normally free apps. I use regular SC and it works great. I advise that you have some built-in memory and EMM to use for swap space. Can anyone offer reasons why to choose SSC over SC? > -----Original Message----- > From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu¨On > Behalf Of I > Al-Khars > Sent: Tuesday, August 07, 2001 6:54 AM > To: HPLX-L@uconnvm.uconn.edu > Subject: super carousel software > > > Did any one try the super carousel software. I have plan to buy this > software from thaddeus.com > > _________________________________________________________________ > Get your FREE download of MSN Explorer at > http://explorer.msn.com/intl.asp > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 11:25:08 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: Battery trouble MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > The palmtop often says "battery error, push ESC key". If the feeder is not p > gged the palmtop suthdown and power off. > > When POWERON, the palmtop restart again and, sometimes, the data in the c dr > e are completely lost. > > I changed the battery (main and backup), unplugged the flash card, reinstall > the soft,... the trouble persist. You might try doing a complete reset on the system. This will wipe out all the data in the internal RAM as well as any "oddities" that may have corrupted some system settings. 1. Backup your internal RAM data to your card 2. Remove the main AAs and the backup lithium battery 3. Press and hold down the "ON" key for 30 secs (this squeezes the remaining juice from the circuits) 4. Replace the batteries, and you're back in business. If that doesn't work, you can always try Thaddeus for repairs. - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 20:12:10 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: super carousel software MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit I Al-Khars wrote: > Did any one try the super carousel software. I have plan to buy this > software from thaddeus.com That version of Software Carousel is very good; I upgraded to it a couple of years ago. The "Super" version is just a lot of software preinstalled for you. If you want the software then it could be a good thing for you. If you just want to run your own software in a task swapping environment then just buy Software Carousel (it's cheaper) and install your own programs. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 20:00:14 -0700 Reply-To: Bob Christopher Sender: HPLX Mailing List From: Bob Christopher Subject: DOS Auto Dialer Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: 8bit Has anyone successfully implemented an auto program execution utility to their DOS environment? I am using both Goin' Postal and WWW/LX-POST/LX for email. It seems both could be made more useful if there were a utility to start/run/close these programs. A utility that would perform the send and receive functions every xx minutes. The interval set by the user, say, in 5 or 10 minute increments. I've tried the TSR programs that fake keyboard input to launch one of these programs and perform the ritual of send and receive, but these TSRs all seem to fail at closing the program, waiting xx minutes and starting the cycle over again. Is it not possible to write a DOS TSR, looping batch file or compiled program that could just launch/start/run/close any program every xx minutes? .......................................................... Bob Christopher Littleton, Colorado USA bob@palmtop.com . HP200LX Palmtop .Submini Cameras. Vintage Mechanicals . ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 7 Aug 2001 22:10:42 +0100 Reply-To: hpstaber@COMPUSERVE.COM Sender: HPLX Mailing List From: HP Staber Subject: Re: Pro-Lx MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Shimon Nagar wrote: > > Hi everyone, > Is There any way I can scroll the days section so old task will be = hide? I did not understand your problem. Can you elaborate a bit more in order to be able to help you ? HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 00:19:06 -0400 Reply-To: "M. Lennartz" Sender: HPLX Mailing List From: "M. Lennartz" Subject: Re: DOS Auto Dialer MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > > I am using both Goin' Postal and WWW/LX-POST/LX for email. > It seems both could be made more useful if there were a > utility to start/run/close these programs. A utility that > would perform the send and receive functions every xx > minutes. The interval set by the user, say, in 5 or 10 > minute increments. > > I've tried the TSR programs that fake keyboard input to > launch one of these programs and perform the ritual of send > and receive, but these TSRs all seem to fail at closing the > program, waiting xx minutes and starting the cycle over > again. Is it not possible to write a DOS TSR, looping > batch file or compiled program that could just > launch/start/run/close any program every xx minutes? > .......................................................... Hi Bob, theoretical it is possible to write a TSR, which puts every xx minutes some keystrokes into the keyboard buffer. I would go another way: May be, you know Net-Tamer, the e-mail-program by David Colston. The "kernel" of Net-Tamer, that means the module, that dials up, sends and gets messages and closes the connection, is called "netmail" and available as shareware ($40 ???). It works with only one provider and one mailbox, but you can change the configuration file in a batch, for instance. I tested the shareware for another project, and it works stable and reliable (in the test, I used it for more than an hour with an intervall of 15 minutes for downloading messages.) The shell programm, which calls netmail, I could rewrite and send to you, but I don't know, if this T-Pascal-6 program runs under LX. Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 05:35:30 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: Quick View 1.5 and Mini Dict 1.0 MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Alan sent me his new masterpieces and i am impressed! (if you want them, ask me, not him, he's recovering from a Costa Rica holiday) Quickview does html and pcx among other jewels, and Minidict freed 500000 off my C:\ by removing LXDICT.EXE. So far both are bug-free. (except in Minidict my F1 shows the palmtop voltage, but when pressed shows garbled "About" text which will only go away with an F10. Also, the beeping, each time it finds a word, is a bit annoying) Other than that, thank you Alan for this wonderful addition to reasons to stay with the LX. btw. i see less and less FS announcements - meaning there is nothing on the market to replace the 'palmi', as the Germans call it. ) ) ( ( ) ) _|****| Nathalie enjoying a cup while waiting for DICT words ( | | `|____| ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 05:30:49 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: Re: 32 categories vs 16 subsets in GDB MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Ed Keefe's article prompted me to create the following macro as a solution: {Shift+End}{Copy} {F10}{F6}{F2}{Paste}{F10}{Paste}{F10}{F10} if called in a note field in front of an SSL line lets me see as many subsets as i want Q: why do searches work faster if the note field is put into page 2 ? Nat ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 07:39:49 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: SMS Question MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Mon, 30 Jul 2001 09:48:53 -0500, Chris Lott wrote: ÝSnipped some¨ > I tried once > on my own to figure it out, and was not successful. First you have to know if you cellphone provide this service. Then you have to know that your provider supports it. Then you have to know the smsc number andf enter it in to your phone. Sms is only avalible in gsm based systems (AFAIK..probably some two way pager systems in US++) If you have a working setup on your phone you could send me a message on +4790199462 and I will recive it instantly on my phone. > I saw some recent posts on SMS from within POST/LX. I'm currious > also how/why people are combining SMS with their POST/LX program. As Stefan wrote it is to make it easy to write. I also use the Post/Lx to transfer/store messages I want to keep. > -Chris "SMS Novice" Lott Regards -- Martin "SMS king" Bergvill :-) ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 07:40:04 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: SMS Question MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Thu, 2 Aug 2001 18:45:06 +0100, HP Staber wrote: > copied into an SMS and sent to my cellphone. This way I know if > something arrived in my mailbox and I have a fair idea about the > contents as well. I have this service on my cellphone. But it is not fun reciving spam and also get notified on the phone. I have added filters so that I am not notified when the subject is something obvious. I have changed my emailadress on this list. Maybe that will reduce the spamamount. But I guess I am already screwd. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 07:40:25 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: Days Program MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Sat, 4 Aug 2001 06:49:28 -0700, Bob Christopher wrote: > I've tried to DL Daivd Bird's Days program from SUPER but > have had no success. This program gives the seconds, > minutes, days, weeks, months years, etc between two dates. > Has anyone successfully DL this program? If so, could you > email it to me. Thanks in advance. I have "Days" here somewhere. I am not sure what version it is. But I wrote him a email a long time ago regarding a bug. Then I got a new version in return. I can mail it to you if you want. I am not sure where I found my orginal copy Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 08:01:07 -0500 Reply-To: Theodore Heise Sender: HPLX Mailing List From: Theodore Heise Subject: Re: SMS Question In-Reply-To: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Wed, 8 Aug 2001, Martin Bergvill wrote: > Sms is only avalible in gsm based systems (AFAIK..probably some two way > pager systems in US++) SMS is available on Verizon (TDMA) systems in the USA. There may be others, but I don't know. Ted -- Theodore Heise West Lafayette, IN, USA ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 08:07:55 -0500 Reply-To: Theodore Heise Sender: HPLX Mailing List From: Theodore Heise Subject: Re: SMS Question In-Reply-To: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Wed, 8 Aug 2001, Theodore Heise wrote: > SMS is available on Verizon (TDMA) systems in the USA. There may be > others, but I don't know. I must need another cup of coffee. That should be CDMA above. Sorry. Ted ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 12:17:31 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: FLUFF: OT (sorta): Do ISA to PCI adapters exist? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Mon, 6 Aug 2001 02:54:01 +0000 (GMT), Russel Brooks wrote: > Tim wrote: > > I'm "moving mother boards around" (to upgrade my main PC's CPU) and will > > lose access to a board that had both ISA and PCI slots in it. > > Keep an old pc around to support your other old hardware. > You aren't limited to a single pc. Why do you have to talk about me all of a sudden :-)) I have a hardware graveyard here :-) Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 11:17:12 -0600 Reply-To: "Robert K. Meyer" Sender: HPLX Mailing List From: "Robert K. Meyer" Subject: OT: HP Photosmart 618 MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Did a lot of research and purchased the HP Photosmart 618 digicam. Requirements: 1600x1200 resolution Compact flash (compatible with LX200 & OB800 Runs of AA's Nice to have Lesser resolutions Manual overides Boy, am I pleased. The pictures are amazing. Have taken pictures in dim light with no flash. They are incredible (a tripod helps). CNET's reviewer of this camera had a bad day or bad unit. Other cameras have more resolutions. This has 1600x1200 and 800x600. Thought others would be nice, but MS Photoed takes care of that. I will probably take most pix at the higher resolution so I'm not sorry later. HP specifies W98 or above. Tried it on USB w/W95b. Drivers install OK, shows error in device manager. This is not a significant problem. Pictures can be transferred by putting the CF in the computer. All other software seems OK. Recently obtained an RCA Lyre 2204 MP3 player. Uses CF and AA's. With the price I paid on eBay, got a CF reader for my desktop and a 64MB Sandisk flash with the player thrown in the deal. Seems like most MP3 players run off AA's but not CF. Many digicams run off neither. Bob -- R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY http://w3.union-tel.com/~bmeyer/ The stone... Psa 118:22 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 11:22:13 -0600 Reply-To: "Robert K. Meyer" Sender: HPLX Mailing List From: "Robert K. Meyer" Subject: OT: Laptop with Reflective LCD Comments: To: List OB MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit A friend was going purchase a Compaq PDA to run some windows mapping software. I told him that his OS would not support Win 9x. What he needs is a W9x machine able to be used in daylight (reflective LCD) and be durable. Panasonic seems to have a Toughbook that may do that, put they are pricey. Any ideas? Bob -- R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY http://w3.union-tel.com/~bmeyer/ The stone... Psa 118:22 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 19:47:49 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: Re: OT: HP Photosmart 618 In-Reply-To: <3B717418.BD96A286@union-tel.com> MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Le Wed, 8 Aug 2001 11:17:12 -0600 "Robert K=2E Meyer" a =E9crit: > Did a lot of research and purchased the HP Photosmart 618 > digicam=2E Had you tried the Pentax EI 200 ? Almost same caracteristics than the Photosmart, plus an 3x optical zoom=2E Plus two great options for palmtop users wanting to upload their pictures on a web site using cellular phone, without making to much image processing on their palmtops : - An automatic detection of the camera position (portrait / landmark)=2E No need to use image processing routine to rotate the image=2E=2E=2E - The "Digita" OS, permitting to create some applets directly in the camera=2E Still need a function permitting to reduce the resolution to something like 400x300, but the firmware being upgradable, we can try to ask=2E=2E=2E ;-) I tried it sometime ago=2E No problem with my compact flash card, and no JPEG compatability problem with the image processing routines I use=2E I tried several other cameras, none has all these features in the same box=2E=2E=2E Jacques=2E ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 12:53:06 -0500 Reply-To: Thomas Rundel Sender: HPLX Mailing List From: Thomas Rundel Subject: Re: Fwd: Ýroboweb¨ Message Zero MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Daniel, I'm not a Roboweb user, at least not yet, but I still believe that _all_ topics which have to do with the HP 200LX and its software should be discussed here. Even if people are not using all programs, discussions about them are usually interesting and useful, and perhaps even lead to more people using these programs. But as I now understand, Roboweb is not supported on the other list exclusively, and discussions can still take place here, so this is not an issue any more. Tom www.rundel.net/palmtop On Mon, 6 Aug 2001 13:54:44 +0200, Daniel Hertrich wrote: > The same! > I really appreciate Tony'S efforts regarding roboweb and all the > maintaining and supprort he gives. But I also don't think it is > necessary to do that off this list. > > But we are roboweb users. > Maybe non-users may think different. > > GTX > daniel ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 8 Aug 2001 12:53:11 -0500 Reply-To: Thomas Rundel Sender: HPLX Mailing List From: Thomas Rundel Subject: Re: super carousel software MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable On Tue, 7 Aug 2001 11:21:51 -0400, Ed Padin = wrote: Ýsnip¨ > Can anyone offer reasons why to choose SSC over SC? If someone is a new user of the 200LX, SSC is great because it saves one from the hassle of downloading and setting up a bunch of apps. All the good freeware and shareware apps are preinstalled and ready to use out of the box. The user just needs to register those shareware apps which he intends to use. On the other hand, someone who already has all the software and just wants to add task switching doesn't need SSC, for him SC will do just fine. Tom www.rundel.net/palmtop ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 00:37:05 -0400 Reply-To: Andrew King Sender: HPLX Mailing List From: Andrew King Subject: Re: OT: Laptop with Reflective LCD, try an Omnibook.... Comments: To: bmeyer@UNION-TEL.COM MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit >Subject: OT: Laptop with Reflective LCD > Date: Wed, 8 Aug 2001 11:22:13 -0600 > From: "Robert K. Meyer" > >A friend was going purchase a Compaq PDA to run some windows >mapping software. I told him that his OS would not support >Win 9x. What he needs is a W9x machine able to be used in >daylight (reflective LCD) and be durable. > >Panasonic seems to have a Toughbook that may do that, put >they are pricey. Any ideas? > >Bob >-- >R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY Bob I would suggest one on the earlier HP Omnibooks. The 300, 425 and 430 are very compact and run WIN 3.1 (but not WIN9x). The earlier models also look exactly like a twice size 200LX..... The 530, 600 and 800 are bigger but can run WIN 9x. All are excellent portable computers. Check out http://home.earthlink.net/~qman/ near the bottom of the page. -- Andrew King Ann Arbor Michigan technology is the answer, what was the question? ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 10:02:55 -0600 Reply-To: "Robert K. Meyer" Sender: HPLX Mailing List From: "Robert K. Meyer" Subject: Re: OT: HP Photosmart 618 Comments: To: Jacques Belin MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit It is the same camera. HP and Pentax developed it together. May be differences in the bundled software as in the 618 and 618xi. The camera OS apparantly has scripting capabilities. Don't see scripts in the manual, but I've hardly gotten into the manual. Bob Jacques Belin wrote: > > Had you tried the Pentax EI 200 ? > -- R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY http://w3.union-tel.com/~bmeyer/ The stone... Psa 118:22 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 09:56:10 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: OT: HP Photosmart 618 MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > > Did a lot of research and purchased the HP Photosmart 618 > > digicam. > > Had you tried the Pentax EI 200 ? > > Almost same caracteristics than the Photosmart, plus an 3x optical zoom. Steve's Digicam website describes them as the same exact camera (a collaboration between HP and Pentax) http://www.steves-digicams.com/hp_c618.html - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 19:14:57 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: Re: OT: HP Photosmart 618 In-Reply-To: <3B72B42F.A0D6B599@union-tel.com> MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Le Thu, 9 Aug 2001 10:02:55 -0600 "Robert K=2E Meyer" a =E9crit: > It is the same camera=2E HP and Pentax developed it together=2E You are true=2E There is an HP logo on the Pentax's screen=2E ;-) > May be differences in the bundled software as in the 618 and > 618xi=2E The camera OS apparantly has scripting capabilities=2E > Don't see scripts in the manual, but I've hardly gotten into > the manual=2E Go to http://www=2Edigitaphoto=2Ecom and http://www=2Edigitacamera=2Ecom for scripts examples=2E=2E=2E Jacques=2E ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 19:48:28 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: Re: OT: HP Photosmart 618 In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Le Thu, 9 Aug 2001 09:56:10 -0700 Longden Loo a =E9crit: > Steve's Digicam website describes them as the same exact camera (a > collaboration between HP and Pentax) >=20 > http://www=2Esteves-digicams=2Ecom/hp_c618=2Ehtml Very good review=2E :-) The are also reviewed at=20 http://www=2Epcphotoreview=2Ecom/dc/reviews/show_all=2Ecfm?ProductID=3D560 (HP 618) and http://www=2Epcphotoreview=2Ecom/dc/reviews/show_all=2Ecfm?ProductID=3D502 (Pentax EI 200) Go to the "Sample Photos" section for the EI 200, you will see some very good examples under very low light conditions, and what it can do in macro mode=2E=2E=2E :-) Jacques=2E ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 13:06:31 -0500 Reply-To: "randys@tsmser.com" Sender: HPLX Mailing List From: Randy Simonson Organization: TSM Services, Inc. Subject: Flexpad Questions MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit I am trying to learn Flexpad on my HP200LX and have the following questions: What is the difference between catagories, labels, sections and bookmarks, and in what situation would each be used? How do I transfer 300 names and addresses from the address program in my HP200LX to Flexpad? Is there a best way to type in names, addresses and phone number into Flexpad? Should each entry (like a name and address) be separated with a line space or should no line space be used? Should subjects be grouped together or just be entered free form? When picking a catagory and getting the results, the lines of text won't rap the words. So I get part of the first line and none of the second line. Is this the way it is suppose to be? Thanks, Randy P.S. I tried to send these questions to the Flexpad list (flexpad-users@yahoogroups.com) but my post will not come up. Is the list down? ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 21:49:59 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: MIDI via IR.EXE to Siemens phone? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, I have a question regarding IR.EXE by Andreas Garzotto: Did anyone manage to send a MIDI file to the Siemens S25 or S35 phone in order to use it as a ring tone? I have tried it (Ir.exe oput midifile.mid) (yes, I have converted it to MIDI0 first with midi1to0 from the lxmidi package), IR says it sends the file, closes connection after sending, but the phone doesn't use the new melody, but the old one instead (also a custom one). In the spec for the phone is written, a new melody overwrites the old one and is usable as melody #43. I always use melody 43, but the new one simply isn't played. The Siemens spec says also, that the Siemens phones are OBEX compliant. Any ideas? Thanks a lot daniel P.S.: The spec says something about "3COM Midi files". What is that? I think MIDI0 is MIDI0. Or what?? ;-) -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 15:16:30 -0500 Reply-To: Chris Lott Sender: HPLX Mailing List From: Chris Lott Subject: OT: BIOS Compliant Editor? MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit A little off topic - perhaps someone can offer some expert opinions. I reported a few years back that the Elvis VI editor has a mode in which it can be operated that utilizes the BIOS interrupts for screen and keyboard access. This is almost an academic distinction, except that I was using it in conjunction with the obscure DOS CTTY command, which let me operate my computer over the COM port from an external terminal (usually a better screen and keyboard). Anyway, I am working on an embedded project that happens to be remakably like the palmtop. It is an AMD 188 embedded processor, and unlike the palmtop, my design has no screen or keyboard, in the normal PC way of thinking. Instead my mini BIOS uses the COM port for the console, almost identical to how the palmtop works after you issue the CTTY command. My question is this - my co workers who need to use this machine are vi-illiterate. I got to thinking, and I could not think of any other "easy" editor that would support this kind of BIOS operation. Something like Q editor would be great. Does anyone here know of such an editor that will work through the BIOS? Thanks, and sorry for the off topic post. -Chris Lott -- ************************************************************************ R. Christopher Lott, P.E. rclott@ro.com Alpha Beta Technologies, Inc. 3112 12th Ave S.W. PHONE: 256-534-9067 Huntsville, Alabama 35805 FAX: 256-534-9069 ************************************************************************ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 9 Aug 2001 17:54:10 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Re: MIDI via IR.EXE to Siemens phone? Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Daniel Hertrich" > P.S.: The spec says something about "3COM Midi files". What is that? I > think MIDI0 is MIDI0. Or what?? ;-) Sorry that I don't know much about your problem, but one thing: MIDI0 can be multiple voices on a single track, as well as a single voice. Mobile phones and Palms can only handle single voices, hence the so called 3COM Midi files. If there is the slightest chance that your file has more than one voice, even part of the time, it will probably not play. HTH Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 00:06:35 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Fluff: FreeCell #892 Hard MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Players of Curtis Cameron's FreeCell may enjoy (or hate) playing game #892; I found this one much harder than other recent FC games I've played. One more down, thousands to go... :-) Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 02:57:37 +0200 Reply-To: Tomas Moberg Sender: HPLX Mailing List From: Tomas Moberg Subject: FS:PCMCIA modem & memory MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Hi! I am selling two PCMCIA cards. I know what I gave for them but am not expecting to get that much for them. Make an offer. (In $ or Swedish krona) Shiping is extra. I have a SMART MODULAR TECHNOLOGIES FAX/MODEM & MEMORY CARD. 6Meg and 2400bps. Its a combo card with two in one. One MEGAHERTZ X-jack (no adaptor required,the phone cord plugs rihgt in) 14 400bps PCMCIA MODEM. Make me an offer if You have the slightest interest. /tomas moberg Uppsala ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 06:44:45 -0400 Reply-To: nxw988e@TNINET.SE Sender: HPLX Mailing List From: Lars Hedstroem Subject: Re: more problems MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Daniel wrote: > > If I were you, I would take the palmtop apart once more, clean > everything, specially the contacts between keyboard and mainboard and > the key contacts themselves, and reassemble it. Maybe this halps. I did so and it seems as it works now, God knows what was wrong. > Strange -- what do the plastic keys in another way than you if you > press the black dots manually? I noticed on my old LX that these black dots were very worned. They must sure be unable to close the circuit sooner or later after a long usage. Lars ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 06:44:47 -0400 Reply-To: nxw988e@TNINET.SE Sender: HPLX Mailing List From: Lars Hedstroem Subject: nbsp MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi For the first time I am trying to construct some more advanced html-pages with the LX. It seems as hv doesnt support non breaking space? That is this sign   Lars ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 13:27:32 +0000 Reply-To: Stefan.Peichl@T-ONLINE.DE Sender: HPLX Mailing List From: Stefan Peichl Subject: Re: MIDI via IR.EXE to Siemens phone? Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Daniel Hertrich wrote: > Did anyone manage to send a MIDI file to the Siemens S25 or S35 phone > in order to use it as a ring tone? Do you have a list of the non standard Siemens AT commands? I once printed a list and I think it was from www.nobbi.com The AT¬SBNW command is used to load logos and ringtones. In order to load a new MIDI ringtone, you have to issue: AT¬SBNW=3D"mid",0,1 > 4D54686400000...... (CTRL-Z) You have to enter the command, and the phone answers with '>'. You then have to enter your data in hex and finish the input with CTRL-Z. If you want to do it more than once, I recommend to write a ROBOT script which takes a MIDI file as input. Nice exercise. Stefan ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 10:52:54 -0500 Reply-To: Barry Sender: HPLX Mailing List From: Barry Subject: Re: OT: BIOS Compliant Editor? MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit Chris Lott wrote: > My question is this - my co workers who need to use > this machine are vi-illiterate. I got to thinking, and I > could not think of any other "easy" editor that would > support this kind of BIOS operation. Something like > Q editor would be great. Does anyone here know of > such an editor that will work through the BIOS? I don't know if this is powerful enough for you but I just checked the source of PC Magazine's TED (Tiny EDitor) and it uses the BIOS for I/O. I'm not sure that's actually what you need, though. I think for redirection you need something that uses DOS. Ted does come with source and it wouldn't be too difficult to modify it to use DOS functions instead of BIOS functions. I think it's already using DOS functions for display (but check closer, I just took a quick look) so you'd just need to modify the key input. This is a very small (2,984 bytes) editor that works fairly well and is easy to use and can be learned in it's entirety in about 10 minutes. Most people would just start using it. It's pretty intuitive and doesn't have any gotchas that I recall. I used it for a long time on my 95lx when I just had a 512k sram card. I'm sure Q (Qedit) goes right to the hardware. They have to do do the things they do as fast as they do. I did a quick search through the doc file for an old version I have and didn't find the word BIOS, but I'm sure it is direct. There are also a number of expanded versions of Ted that various people have made. Most are still under 5 or 6k but add a lot of features. Some are very well done. They all used to be in the Compuserve library. You might check Simtelnet. I don't remember their names but the binaries had names like E.com and H.com (I remember these two. There are others). I don't remember that they also use the Bios but they probably did and they come with source. I have Ted if you need it. I probably also have the others but a quick search didn't turn them up. I have about a thousand old floppies and a couple of hundred Zip disks and a few hundred CDs with old stuff on them. None of it is indexed. Barry Barry ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 12:42:25 -0400 Reply-To: "M. Lennartz" Sender: HPLX Mailing List From: "M. Lennartz" Subject: Flash Card MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Hi all, I've got a 2 MByte Intel/M-systems Flash Card Intel 28F008SA (labeled as digital prgm card). The 200LX doesn't recognize it. Is it possible to use it with an in-built driver or additonal software? TIA Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 19:14:10 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Good file compression program MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, I'm looking for a program whichi is good to compress a part of me internal RAM disk. It must be very reliable! Background: I have reconfigured WWW/LX to use my Accton Ethernet card to go online. Before that I have stored all my email on the flash card, but now I had to move all Post/LX mailboxes and the folders in which Post/LX filters automatically to the internal RAM drive and I run out of space soon. So I think the best option (besides buying an upgrade which is too expensive for me) would be to compress the Post/LX files, which should be very effective, since these files are nearly plain text. Please recommend what I can use (jam, diet, stacker....)! Thanks a lot daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 10 Aug 2001 21:04:02 -0600 Reply-To: "Robert K. Meyer" Sender: HPLX Mailing List From: "Robert K. Meyer" Subject: Re: OT: Laptop with Reflective LCD Comments: To: omnibook@elektro.cmhnet.org MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Thanks for response. I will pass the info along to my friend. Seems logical to me that all laptops would have a reflective backlit screen. Industry must want to keep us in dark rooms. I remember reading an article in one of the big industrial electrical engineering magazines 25 years ago that LCD wrist watches never catch on. Never had an LED watch myself. I wanted to tell time in daylight. Industry wanted us in caves. I would just as soon be able to compute in bright sunlight. Bob -- R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY http://w3.union-tel.com/~bmeyer/ The stone... Psa 118:22 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 13:14:09 +1000 Reply-To: David Eggins Sender: HPLX Mailing List From: David Eggins Subject: Maybe sell my HPLX 200, DS, 32mb??? MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hello I have the following, and am thinking about selling it all, so would like to get some offers to see if it is worth selling. -- HPLX 200, Double speed, and 32mb from Rundel Datentechnik. The upgrade was done in June 1998. -- Australian 240v power adapter for 200LX -- All boxes and manuals for the 200LX, unused, as I have 2 sets of manuals) -- Serial Cable for 200LX -- WWW/LX, POST/LX 2.x. Tis is the previous version, and no longer supported, but does the job fine for me. -- ABC/LX (Battery charge software) -- Software Carousel -- Simple Technology 33.6 card modem with SimpleJack (the cool little adapter that just fits over a normal phone cable), plus one spare simplejack -- 1mb Grid PCMCIA card (Not flash, needs battery) -- 2mb Grid PCMCIA card (Not flash, needs battery) -- Spare battery for 1 of the above PCMCIA cards -- Heaps of downloaded HPLX freeware software I will burn to CD if you like. -- Original HP leather wallet for HP Palmtop. I can send JPG pictures of all if interested. The 200LX had the crack appear in August 1998, but I fixed it, and it has not come back. The repair job is nearly invisible. Also, the spring appears to have broken on the PCMCIA door. I mostly keep a card in there, which is probably why this has happened. Also, for some reason, ever since the memory and speed upgrade, the bottom of the 200LX has had a slight buckle so that it does not quite sit on the four feet. I do not know if this is just a side affect of the upgrade, but it has not bothered me, nor affected the use of the 200LX, so I ignored it. I have not dropped or damaged it in any way, and it is in good condition other than the things mentioned above. I still use it a little, but have scaled down my use lately as I have computers nearly everywhere I go. I never thaught I would say this, but I am considering getting a Palm PC of some kind, because as a software developer for Windows, I could develop my own software for it. (I never had the time, not interest to learn the software development tools on the 200LX) Please email me directly at david@eggins.com, as I do not always get time to read the list, but usually peruse the archives. Thank You David david@eggins.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 11:09:18 +0200 Reply-To: "Bel, Michel" Sender: HPLX Mailing List From: "Bel, Michel" Subject: Re: Good file compression program MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Daniel Hertrich wrote: > Hi friends, > I'm looking for a program whichi is good to compress a part of me > internal RAM disk. > It must be very reliable! Before I upgraded to my 220MB Sandisk I used JAM for quite some time without any trouble. I can vote for it's reliability - never lost any data. Michel ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 11:18:30 +0200 Reply-To: "Bel, Michel" Sender: HPLX Mailing List From: "Bel, Michel" Subject: Re: TaskBar Comments: To: "M. Lennartz" MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Michael Lennartz wrote: >Hi all, > on Quinton Jones Website I've found the description and screenshot of > "TaskBar", but the link to the website is dead. I searched on A wild search got me TBLX18 as a free download from a Japanese site. As I do not know the status, I can not post it, but can send it to requestors. Docs are in Japanese but a simple analysis of the file will show how to configure it. Example( of my personal version) the Ý option ¨ give main menu items displayed the < option> a deeper level submenu displayed the hex values are the key values for starting the linked program. Ýoption¨ taskbar=2 allkill=4000 tblxend=1 123g=08A9 ip=07BD Ýrun¨ dosline=2000 Ýfind¨ Filename=6e00 Contents=6E00 Ýprogram¨ Smmx=A700 Tasklist=c300 KeyM=1300 PIM=0 Planning=0 Zoom=7f00 Appointments=b000 Phonebook=b400 ToDo=1400 Project=b300 Clock=7900 Regards, Michel ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 06:45:24 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: Good file compression program MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Fri, 10 Aug 2001 19:14:10 +0200, Daniel Hertrich wrote: > Hi friends, Hellu there > I'm looking for a program whichi is good to compress a part of me > internal RAM disk. > It must be very reliable! I use Jam and are very satisfied. I have not had a problem for a very long time. > Background: > > I have reconfigured WWW/LX to use my Accton Ethernet card to go online. I do exactly that every day. > Before that I have stored all my email on the flash card, but now I had > to move all Post/LX mailboxes and the folders in which Post/LX filters > automatically to the internal RAM drive and I run out of space soon. I have the same problem. I have emailfolders on the Cdrive and then newsfolders on the G Jamdrive. > So I think the best option (besides buying an upgrade which is too > expensive for me) I have too.. I have 500kb free on Gdrive and about 1400kb-Maxdos free on the Cdrive. When I get around to it I will send a backupunit to Hal and get it upgraded.. (I get around to it=when I get the money for it) > would be to compress the Post/LX files, which should > be very effective, since these files are nearly plain text. I have had great success with this for years. I figured that since the newsfolders in Www/lx are mostly just sitting there then I could put them on a Jamdrive. > Please recommend what I can use (jam, diet, stacker....)! I would go for Jam.. I have not used Stacker or Diet On the Hplx. I used Stacker long time ago on the desktop. I have a 8mb ds machine and I have Jammed about 3.2mb of it for years. I back it up to a flashcard by pkzipping the Cdrive and then just copy the jamdrive file to the flashcard. > Thanks a lot You are welcome :-) Regards PS!1 Do you have an idea when you will have the info about Vcards/6210 up on your webpage? PS2! See other mail about Ericsson T39 and the Hplx :-) Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 06:45:28 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Ericssons new T39m and the Hplx MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi I should have used my money to get my backup hplx upgraded but I could not resist the new mobil phone from Ericsson. The new T39m. For those who do not know it it has these key features: Gprs Hscsd Bluetooth Irda Wap 1.2.1 Voicecontrol Voicememo(90 seconds) Calender Calculator Alarmclock Phonebook with more info for each name(511 enteries total) with SyncMl ++ lot more.. It even got a copy of the old Commondore 64 game "Styx" :-) All this in a phone which is the size of a crediccard+arial and weighs 86gram. I have used it now for a couple of days and I must say that I am impressed. I still have my Nokia 6210 but it is now huge and will probably be sold or put away somehere.. :-) I have not yet charged the battery(!). The supplied battery has a standbytime of max 300 hours(!). It was way below half full when I first bought the phone. Now I got 78hours standby time left or 1.5 hours talktime. I have orded a "big" battery for this phone. It has a standbytime of 700 hours. (figure out how many days that is for yourself :-) I tested it with Hplx with the same AT string I used with the 6210 to establish a HSCSD connection through WWW/LX. It did not work. It probably need some special AT strings to get it to work. But it did however work with 9600bps..AT&F. I will get back to this when I know more about this. I have posted some questions on news. I have not yet tested it with Ring.com, but it seems that it makes some more EMI problems than the 6210. This is yet to be confirmed. Hopefully it will not be a problem. I also transfered Vcards from the Hplx to the T39m the same way I did with the 6210. This worked like a charm. Only problem was when the Hplx phonebook had a lot of info in the notefield..the phone just crashed and had to be rebooted. (this also happend with the 6210..not a problem) The Ericsson is a great phone and I hope to sell many of them in the shop I work. Nothing from Nokia even comes close at this point in time. But when the 6310 are launched it does not come close either.. Strange because I am really a Nokia man, but now I have been blown away with the T39m. A lot of things to get used to but still a great phone. (Yes you can use it to call people too :-) Things I need to get tested is: To use GPRS(always online) with WWW/LX. Any suggestions? How to use HSCSD with the Hplx How to transfer Vcalender to the phone from Hplx. +Suggestions from you guys PS! I will try to get the Siemens S40 tested also.. Have to do it tomorrow. We have just one left which is already sold. I will try it out tomorrow saturday. If I remember correctly it does not support HSCSD over irda...Daniel do you know anything about this? Is the irda limited to 9600 or something? It is sold with a cable so it seems like It need it for High speed That is all for now.. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 06:45:30 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: SMS Question MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Wed, 8 Aug 2001 08:01:07 -0500, Theodore Heise wrote: > On Wed, 8 Aug 2001, Martin Bergvill wrote: > > > Sms is only avalible in gsm based systems (AFAIK..probably some two way > > pager systems in US++) > > SMS is available on Verizon (TDMA) systems in the USA. There may be > others, but I don't know. TDMA..is this gsm at 1900MHz? Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 11:44:17 -0400 Reply-To: flora@MINPOST.NU Sender: HPLX Mailing List From: Rolf Aronsson Subject: Pcmcia blocked! MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable 11-Aug-01 Hallo members on this "old" list......... I am happy to come back to this HP-list after holding up some years. I have used HP since the beginning with HP95. Now I have HP200LX upgraded to 32 Mb. It works excellently. This is the case with those I used earlier, too. As all of you know there is no personal life without this palmtop near the heart! I am glad to see this list still be alive. The HP-community still going strong, too. Thanks to the HP-line! Now my problem. It is the worse hazard that ever have happened to me with this machine during the years. Two weeks ago, after running the HP-test program (of/esc+on/release esc), the card, that was in the slot, did not want to give any information. I get the message "Drive not ready," in spite of the card being there. I tried rebooting, even cold one with "n", but no change. I tried other pcmcia-card. They worked! The primary card, that now is not working, I have used a long time, perhaps 4 year or longer. It is a 10 mb SanDisc and has given me no trouble during the years. There is a lot of valuable information on it. I MUST have it back. What to do??????? What has happened? The information on the card is of the dignity that I pay money for it to come back! Regard from Rolf Aronsson, Sweden. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 18:26:04 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: MIDI via IR.EXE to Siemens phone? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Stefan, On Fri, 10 Aug 2001 13:27:32 +0000, Stefan Peichl wrote: > Do you have a list of the non standard Siemens AT commands? Yes. > The AT¬SBNW command is used to load logos and ringtones. > In order to load a new MIDI ringtone, you have to issue: > > AT¬SBNW="mid",0,1 > > 4D54686400000...... (CTRL-Z) Thanks! This is just what I need! I tried it, but I had to give one more number at the end in order to get a > rather than an ERROR AT¬SBNW="mid",0,1,1 > then I entered the hey code of the beginning of a midi file. ctrl-z braught up another ERROR, but I could then read exact the same as I wrote into the phone with the AT¬SBNR command, i.e. it has been saved. The phone didn:t play anything, though. Do you know what the exact meaning of this last value is? In the data sheet, it is said to be the "maxNumber" (=maximum number of packets). Which packets are meant? Another thing I wondered about was "Limitation: The maximum pdu size is 176 bytes (or 352 charcaters)". My MIDI files are up to 1.5kB in size! > If you want to do it more than once, I recommend to write a > ROBOT script which takes a MIDI file as input. Nice exercise. Nice idea. I looked into the robot.doc, but I couldn't find the appropriate commands to read a file and write the hex values to the phone. BTW: Is the phone connection equivalent to the "TCP" connection mentioned in the docs? GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 09:32:22 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: nbsp Comments: To: Lars Hedstroem MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Sure it does. Try this: http://www.dasoft.com/indexHV.html right after the image with the words "D&A Software" and before the icon for WWW/LX, there are three   entities. There are more throughout the D&A Software Website. It may be that your font has nothing in place where that "character" shows up? Avi Lars Hedstroem wrote: > Hi > > For the first time I am trying to construct some more advanced > html-pages with the LX. > > It seems as hv doesnt support non breaking space? > > That is this sign   > > Lars > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 13:28:30 -0400 Reply-To: Steve Sender: HPLX Mailing List From: Steve Subject: Re: OT: BIOS Compliant Editor? Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Chris Lott wrote: > My question is this - my co workers who need to use > this machine are vi-illiterate. I got to thinking, and I > could not think of any other "easy" editor that would > support this kind of BIOS operation. Something like > Q editor would be great. Does anyone here know of > such an editor that will work through the BIOS? Aha! A job for EDLIN! It's just a little less scary than vi though. Steve ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 13:21:48 -0500 Reply-To: Chris Lott Sender: HPLX Mailing List From: Chris Lott Subject: BIOS Compliant Editor MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Just to follow-up, after following a tip from Barry, it turns out that the VDE editor has a mode that uses the BIOS console I/O functions instead of direct hardware writes. While I haven't tested it, it might also work with the CTTY style of operation like Elvis does. -Chris Lott -- ************************************************************************ R. Christopher Lott, P.E. rclott@ro.com Alpha Beta Technologies, Inc. 3112 12th Ave S.W. PHONE: 256-534-9067 Huntsville, Alabama 35805 FAX: 256-534-9069 ************************************************************************ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 21:52:23 +0200 Reply-To: Rolf Aronsson Sender: HPLX Mailing List From: Rolf Aronsson Subject: Pcmcia was blocked! MIME-Version: 1.0 Content-Type: multipart/mixed; boundary="----=_NextPart_000_005B_01C122AF.E6E6EF80" This is a multi-part message in MIME format. ------=_NextPart_000_005B_01C122AF.E6E6EF80 Content-Type: multipart/alternative; boundary="----=_NextPart_001_005C_01C122AF.E6E6EF80" ------=_NextPart_001_005C_01C122AF.E6E6EF80 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable 11-aug-01 Thanks for the interest. Hope there are anybody more on the list, who = know the way out of this blocked flashcard. The constructor of the = SanDisc flashcard perhaps know about the system. I can not believe, = that the data is away. There ought to be any program or so, which can = break into the card. And more - what did happen in the seftesting mode? = Sram-cards can manage it but not flashcards??? I did not know anything about the risk for the flashcards when doing = this selftesting. This BUG I want the HP-user to know about. The Data on = my card is of a very important sort, and as I said earlier, I pay for to = have them back! Regards from Rolf Aronsson. P.S. Dear Daniel. I think I joined the list in the beginning 1990th. I = do not know when the list started. Perhaps anybody knows!? D.S. ------=_NextPart_001_005C_01C122AF.E6E6EF80 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable
11-aug-01
 
Thanks for the interest. Hope there are anybody more on the list, = who know=20 the way out of this blocked flashcard. The constructor of the SanDisc = flashcard=20 perhaps know about the system.  I can not believe, that the data is = away.=20 There ought to be any program or so, which can break into the card. And = more -=20 what did happen in the seftesting mode? Sram-cards can manage it but not = flashcards???
 
I did not know anything about the risk for the flashcards = when=20 doing this selftesting. This BUG I want the HP-user to know about. = The Data=20 on my card is of a very important sort, and as I said earlier, I pay for = to have=20 them back!
 
Regards from Rolf Aronsson.
 
P.S. Dear Daniel. I think I joined the list in the beginning = 1990th. I do=20 not know when the list started. Perhaps anybody knows!?=20 D.S.
------=_NextPart_001_005C_01C122AF.E6E6EF80-- ------=_NextPart_000_005B_01C122AF.E6E6EF80 Content-Type: text/x-vcard; name="Rolf Aronsson.vcf" Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="Rolf Aronsson.vcf" BEGIN:VCARD VERSION:2.1 N:Aronsson;Rolf FN:Rolf Aronsson EMAIL;PREF;INTERNET:flora@minpost.nu REV:20010811T194633Z END:VCARD ------=_NextPart_000_005B_01C122AF.E6E6EF80-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 21:58:16 +0200 Reply-To: Rolf Aronsson Sender: HPLX Mailing List From: Rolf Aronsson Subject: Pcmcia was blocked! MIME-Version: 1.0 Content-Type: multipart/mixed; boundary="----=_NextPart_000_0073_01C122B0.B94FFCA0" This is a multi-part message in MIME format. ------=_NextPart_000_0073_01C122B0.B94FFCA0 Content-Type: multipart/alternative; boundary="----=_NextPart_001_0074_01C122B0.B94FFCA0" ------=_NextPart_001_0074_01C122B0.B94FFCA0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable 11-aug-01 Thanks for the interest. Hope there are anybody more on the list, who = know the way out of this blocked flashcard. The constructor of the = SanDisc flashcard perhaps know about the system. I can not believe, = that the data is away. There ought to be any program or so, which can = break into the card. And more - what did happen in the seftesting mode? = Sram-cards can manage it but not flashcards??? I did not know anything about the risk for the flashcards when doing = this selftesting. This BUG I want the HP-user to know about. The Data on = my card is of a very important sort, and as I said earlier, I pay for to = have them back! Regards from Rolf Aronsson. P.S. Dear Daniel. I think I joined the list in the beginning 1990th. I = do not know when the list started. Perhaps anybody knows!? D.S. ------=_NextPart_001_0074_01C122B0.B94FFCA0 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable
11-aug-01
 
Thanks for the interest. Hope there are anybody more on the list, = who know=20 the way out of this blocked flashcard. The constructor of the SanDisc = flashcard=20 perhaps know about the system.  I can not believe, that the data is = away.=20 There ought to be any program or so, which can break into the card. And = more -=20 what did happen in the seftesting mode? Sram-cards can manage it but not = flashcards???
 
I did not know anything about the risk for the flashcards = when=20 doing this selftesting. This BUG I want the HP-user to know about. = The Data=20 on my card is of a very important sort, and as I said earlier, I pay for = to have=20 them back!
 
Regards from Rolf Aronsson.
 
P.S. Dear Daniel. I think I joined the list in the beginning = 1990th. I do=20 not know when the list started. Perhaps anybody knows!?=20 D.S.
------=_NextPart_001_0074_01C122B0.B94FFCA0-- ------=_NextPart_000_0073_01C122B0.B94FFCA0 Content-Type: text/x-vcard; name="Rolf Aronsson.vcf" Content-Transfer-Encoding: 7bit Content-Disposition: attachment; filename="Rolf Aronsson.vcf" BEGIN:VCARD VERSION:2.1 N:Aronsson;Rolf FN:Rolf Aronsson EMAIL;PREF;INTERNET:flora@minpost.nu REV:20010811T195816Z END:VCARD ------=_NextPart_000_0073_01C122B0.B94FFCA0-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 11 Aug 2001 14:23:13 -0500 Reply-To: theise@netins.net Sender: HPLX Mailing List From: Theodore Heise Subject: Re: SMS Question Martin Bergvill writes: > > TDMA..is this gsm at 1900MHz? According to Steven DenBeste's CDMA FAQ, GSM uses a TDMA interface. I'm not sure what frquency it operates in the US. http://denbeste.nu/cdmafaq Ted -- Theodore W. Heise West Lafayette, IN, USA PGP public key: http://showcase.netins.net/web/twheise/theise.txt ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 06:33:05 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: where is Mark in Seattle MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I am looking for Mark in Seattle. Both addresses return a fault: Mark Willis mwillis@tx3.net or mwillis@foxinternet.net Does anyone know his new e-mail address? ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 03:23:03 EDT Reply-To: Class3Dep@AOL.COM Sender: HPLX Mailing List From: Dennis Vest Subject: Re: TaskBar MIME-Version: 1.0 Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit Is there a place on the web where I can find additional information on Taskbar? I am especially interested in detailed setup info. Michel, I'd love the address to download TaskBar. Dennis ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 04:58:29 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: where is Mark in Seattle MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Sun, 12 Aug 2001 06:33:05 +0200, Nathalie Bugeaud wrote: Nathalir > I am looking for Mark in Seattle. Both addresses return a fault: > Mark Willis mwillis@tx3.net or mwillis@foxinternet.net > Does anyone know his new e-mail address? I got a mail from him from the mwillis@foxinternet.net address not long ago. So it should be real and up. Maybe there are some trouble with the servers or something. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 06:34:58 -0400 Reply-To: nxw988e@TNINET.SE Sender: HPLX Mailing List From: Lars Hedstroem Subject: Re: Viewing files on a Win machine? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Tomas Moberg wrote: > When I try to view text files from my HP on my Windows machine the text > is wrong. My Swedich characters edv is not properly displayed. > Is this due to the ANSI/ASCII translation? I haven't that problem at all, but then I have Win95. Lars ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 14:54:42 +0200 Reply-To: Josef Meyer Sender: HPLX Mailing List From: Josef Meyer Subject: Re: Ericssons new T39m and the Hplx MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi, I recently got a subscribtion as "friendly user" for GPRS from Swisscom, the biggest GSM operator in Switzerland. I am working in the company which has delivered the GSM network + GPRS system to Swisscom. Currently GPRS is working with Swisscom, but not yet officially launched. After the official launch, which will happen in the next few months, all GSM subscribers with Swisscom will automatically have the GPRS subscription. GPRS (General packet radio switching/system?) is a packet switched data service for GSM, which will allow permanent packet data connection to servers. Currently up to 4*9600 bit/s are possible, depending of the number of concurrent users and availability of time slots. Only data amount, not connection time will be charged. Therefore this service is very good for interactive connection to a service, like WAP, email etc. File transfer is evtl. more economic over a switched connection. E.g. HSCSD (High speed circuit switched data) allows a switched connection using up to 4*9600 bit/s time slots. Now I am trying to get a mobile phone like Ericsson R520 or T39, which are both the same from point of view of functionality (R520 is bigger), but different in size and have the features mentioned by Martin below. Martin Bergvill wrote: > For those who do not know it it has these key features: > > Gprs > Hscsd > Bluetooth > Irda > Wap 1.2.1 > Voicecontrol > Voicememo(90 seconds) > Calender > Calculator > Alarmclock > Phonebook with more info for each name(511 enteries total) with SyncMl > ++ lot more.. > > It even got a copy of the old Commondore 64 game "Styx" :-) > > All this in a phone which is the size of a crediccard+arial and weighs > 86gram. > > I have used it now for a couple of days and I must say that I am > impressed. I still have my Nokia 6210 but it is now huge and will > probably be sold or put away somehere.. :-) > > I have not yet charged the battery(!). The supplied battery has a > standbytime of max 300 hours(!). It was way below half full when I > first bought the phone. Now I got 78hours standby time left or 1.5 > hours talktime. I have orded a "big" battery for this phone. It has a > standbytime of 700 hours. (figure out how many days that is for > yourself :-) Ericsson seems to have made a big step towards better battery life... > I tested it with Hplx with the same AT string I used with the 6210 to > establish a HSCSD connection through WWW/LX. It did not work. It > probably need some special AT strings to get it to work. But it did > however work with 9600bps..AT&F. I will get back to this when I know > more about this. I have posted some questions on news. I am keen to know more about your experiences, especially with WWW/LX. > I have not yet tested it with Ring.com, but it seems that it makes some > more EMI problems than the 6210. This is yet to be confirmed. Hopefully > it will not be a problem. My experience with Ericsson phones shows that with all 3.3V models one must have very strong field strength in order to have a low transmitting power of the mobile phone and thus have few EMI problems. With the former Ericsson 4V models (SH888, T10, T18. ...) the IR devices had more power and so the distance between the HPLX and the phone could be much more (>50cm) compared to the 3.3V models, where a maximum of only 20cm between the IR senders/receivers is possible. > I also transfered Vcards from the Hplx to the T39m the same way I did > with the 6210. This worked like a charm. Only problem was when the Hplx > phonebook had a lot of info in the notefield..the phone just crashed > and had to be rebooted. (this also happend with the 6210..not a > problem) How did you do that? I failed in transmitting Vcards between my Ericsson R380 and HPLX using ir.exe oget (Timeout on R380). > The Ericsson is a great phone and I hope to sell many of them in the > shop I work. Nothing from Nokia even comes close at this point in time. > But when the 6310 are launched it does not come close either.. Strange > because I am really a Nokia man, but now I have been blown away with > the T39m. A lot of things to get used to but still a great phone. (Yes > you can use it to call people too :-) > > Things I need to get tested is: > > To use GPRS(always online) with WWW/LX. Any suggestions? > How to use HSCSD with the Hplx > How to transfer Vcalender to the phone from Hplx. > +Suggestions from you guys Please keep us updated! I believe I am not the only person on this list who is interested in your experiences! Maybe sooner or later with the knowledge of all list members we will even be able to make a connection via bluetooth! Josef Meyer ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 09:28:58 -0400 Reply-To: Richard Millard Sender: HPLX Mailing List From: Richard Millard Subject: DC ADAPTER Mime-Version: 1.0 Content-Type: text/plain; format=flowed My old dc-dc adapter I was using in the car for my HP200LX has died. I have been looking for an alternate. I can find lots of 12V dc adapters with the right kind of plugs to fit the LX. However, all of these adapters put out unregulated voltage when the 12V setting is selected (usually about 14~14.5 volts). I can't find an adapter which regulates the output when set for 12V. Does anyone know of a source for a regulated adapter for use in a car which actually puts out 12V? Does anyone know if using a power source of 14~14.5V will damage the LX? _________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 10:40:01 -0400 Reply-To: nxw988e@TNINET.SE Sender: HPLX Mailing List From: Lars Hedstroem Subject: Re: nbsp MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Avi wrote: > Sure it does. Try this: http://www.dasoft.com/indexHV.html > right after the image with the words "D&A Software" and before > the icon for WWW/LX, there are three   entities. There > are more throughout the D&A Software Website. OK, I will have a look there. I expressed myself wrongly, I didn't mean that it didn't work, it looks like this: htmlcode:   texttexttext hv shows _ texttext But one thing hv doesn't support seem to be such a command:
Instead a whole line goes from the left side to the right side. Lars ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 18:58:51 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: SMS Question MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, On Sat, 11 Aug 2001 14:23:13 -0500, Theodore Heise wrote: > Martin Bergvill writes: > > > > TDMA..is this gsm at 1900MHz? > > According to Steven DenBeste's CDMA FAQ, GSM uses a TDMA interface. > I'm not sure what frquency it operates in the US. xDMA is "x division multiple access". T=time, C=code, there are many others. They describe medium access techniques, i.e. it is another so-called network layer than protocols like GSM and co. GSM _uses_ TDMA for medium access, i.e. it uses time slots. Regarding the frequency: here in Europe there are two different GSM systems, one operates on 900 MHz (the "D" networks D1 and D2) and one operates on 1.8GHz (the "E" networks E-Plus and VIAG Intercom). In USA the corresponding system operates at 1.9GhHz, but I ton't know if it is also called GSM. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 18:58:52 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: DC ADAPTER MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Richard, On Sun, 12 Aug 2001 09:28:58 -0400, Richard Millard wrote: > Does anyone know if using a power source of 14~14.5V will damage the LX? Don't do it! Maybe 14V don't damage the palmtop immediately, but the internal voltage regulating circuitry would get warmer than normal, so the ICs would die sooner than with 12V. Another issue in cars is that if you start the motor or use other devices like the starter which disturb the on-board voltage in such a bad way (very high voltage peaks!), the palmtop can easily be damaged. Use a regulated one! GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 14:17:49 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: Good file compression program MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > Please recommend what I can use (jam, diet, stacker....)! I have used Jam to compress part of my palmtop's internal RAM drive. It = worked well and did not give me problems. It does slow down disk access and = take up some lower DOS RAM. I quit using it when I got a 64 Meg internal drive. = I don't think Stacker can be used on just part of a drive. I have not used = diet in TSR mode, although I do still use it to compress *.exe files. Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 21:29:58 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: DC ADAPTER MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Daniel Hertrich wrote: > > Does anyone know if using a power source of 14~14.5V will damage the LX? > > Don't do it! > Use a regulated one! If a regulated supply is difficult to find a small motorcycle battery and a switch could be used. The switch would either charge the battery from the car or run the LX like this... / ---O +-O O--- LX | / Car ---O | O O--- | | | | Motorcycle Battery An LX should run for a l-o-n-g time on a fully charged motorcycle battery. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 21:33:11 +0000 Reply-To: fjkaufman@WORLDNET.ATT.NET Sender: HPLX Mailing List From: "F. Kaufman" Subject: Re: Pcmcia blocked! Comments: To: flora@MINPOST.NU MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit > happened to me with this machine during the years. Two weeks > ago, after running the HP-test program (of/esc+on/release esc), > the card, that was in the slot, did not want to give any > information. I get the message "Drive not ready," in spite of the > card being there. I tried rebooting, even cold one with > "n", but no change. I tried other pcmcia-card. They worked! Unfortunately that TEST routine is ONLY FOR the older SRAM cards and NOT for Flashcards. It can corrupt the formatting information as you have accidently discovered. (by the way, it does not always ruin data but I don't know if there is a way to find out which cards survive). The data is probably on the card but the directory/fat/formatting information is ruined. I'm not sure if you can get to that card using an older version of Norton 4.5 or something like it or not. Sandisk may have something to fix it. A data recovery business might also be able to fix it but I'm not sure. You can use the card again (after deciding the data is not recoverable) by using the fdisk in the d:\bin directory (check its name) and then formatting the card from Filer. WARNING, this will remove all hope of getting that data back but makes the card useable again. Good luck And do NOT use the self test (Escape-ON) for any cards to be safe!!! ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 12 Aug 2001 22:41:56 -0400 Reply-To: Larry Tachna Sender: HPLX Mailing List From: Larry Tachna Subject: Re: Pcmcia blocked! Comments: To: flora@MINPOST.NU In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit >>What to do??????? What has happened? the built in self test program is only for sram cards unfortunately as you found out it sometimes trashes ata flash cards. I would try to use fdisk100 on the card I believe you will find it on the d drive somewhere than format the card ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 09:20:40 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: DC ADAPTER MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Russ, On Sun, 12 Aug 2001 21:29:58 +0000, Russel Brooks wrote: > If a regulated supply is difficult to find a small motorcycle > battery and a switch could be used. The switch would either > charge the battery from the car or run the LX like this... > > / > ---O +-O O--- > LX | / Car > ---O | O O--- > | | > | | > Motorcycle Battery Generally a good idea, but be careful: If you switch the motorcycle battery to the car battery the way you have drawed above, surely the fuse will melt. I think in order to charge a battery, at least a currnt limiting resistor would be needed, because an empty rechargeable looks like a short-circuit to the charging source. I can be wrong, but that's the way I recall it from my EE lectures in university ;-) And this resistor must stand quite a lot of current, you can't use such a standrad 0.25W-resistor! It would be blown away like a fuse. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 09:20:40 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: TDMA and GSM MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, sorry, I made a little mistake here: On Sun, 12 Aug 2001 18:58:51 +0200, Daniel Hertrich wrote: > Regarding the frequency: here in Europe there are two different GSM > systems, one operates on 900 MHz (the "D" networks D1 and D2) and one > operates on 1.8GHz (the "E" networks E-Plus and VIAG Intercom). > In USA the corresponding system operates at 1.9GhHz, but I ton't know > if it is also called GSM. the D and E networks only have these names in Germany, not in entire Europe. But correct is that in entire Europe (like in most countries in the world), GSM900 and GSM1800 is used. What I always wanted to know: Here in Germany the cellular networks have their own "area codes", so if you call a cell phone, say, in the E-Plus network, you always have to dial a "0177" in front of the handset number, regardless, where in Germany (or even in the world) the handset currently is. Every network has its own "area code" (actually in that case this isn't an area code, because it is the same, whereever you are with your phone). Is it the same in other countries, or do cellular networks in other countries seamlessly integrate with the wired network, using the area codes of the "real" spatial areas? TNX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 15:55:08 +0800 Reply-To: Adrian Ho Sender: HPLX Mailing List From: Adrian Ho Subject: Re: TDMA and GSM In-Reply-To: ; from daniel.hertrich@GMX.DE on Mon, Aug 13, 2001 at 09:20:40AM +0200 Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii On Mon, Aug 13, 2001 at 09:20:40AM +0200, Daniel Hertrich wrote: > Is it the same in other countries, or do cellular networks in other > countries seamlessly integrate with the wired network, using the area > codes of the "real" spatial areas? Singapore's too small to justify area codes, so mobile (cellphone & pager) numbers are only distinguished from fixed-lines numbers by a '9' prefix. And yes, we have both GSM 900 and 1800 networks in Singapore, and at least one mobile operator supports auto-switching between networks in areas served by only one band, while still maintaining just one number. You'd need at least a dual-band phone, of course, but that's pretty much the norm here. - Adrian ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 09:56:56 +0100 Reply-To: "Brown, William D" Sender: HPLX Mailing List From: "Brown, William D" Subject: Re: TDMA and GSM MIME-Version: 1.0 Content-Type: text/plain The UK did start out with separate 'area codes' for each provider, and each provider was only allowed to operate in one of the bands (900 or 1800) - measures to avoid a monopoly. However I believe that restriction is lifted, but in practice there are still separate networks, with separate providers. The bad thing is that due to pressure from consumers, you can keep your number now even when you change providers. So there is no longer any way to tell whether you are calling someone on the same provider as you, or another - let alone what band they are on (though I can't see the latter is important). The catch is that a call to another mobile, on a different provider, is *very* expensive. Much more than to a landline, or to another mobile on 'your' provider. The regulator has started to take an interest, on the basis that there is no technical reason for it to cost more to operate the call. So in the UK you do know you call a mobile - all such numbers start 07 now - but you cannot tell if it is a fairly expensive call or a very expensive call until you get the bill. -o- Some mobiles allow you to opt for a package with cheap 'local' calls, and on my Nokia it can be made to display what is the 'local' landline area code on the screen. William D.Ll.Brown ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 14:17:06 +0200 Reply-To: Axel Klag Sender: HPLX Mailing List From: Axel Klag Subject: QuickView 1.5 and MiniDict 1.0 Comments: To: alan@sbox.tu-graz.ac.at MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Hi Alan, i've read about Your progs MiniDict 1.0 and QuickView in the digest, but I could'nt find them at the SuPER-Site both in the Most Popular Files-Section (last modified 4th May 2001) and in the complete Section. Did You get any response or do You know, where I could find them? Thanks a lot, regards, Axel -- *************************************************************************** Axel KLAG * DW-tv * IT-Support * 49-(0)30-4646-7020 * Mail * klag@dwelle.de ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 10:48:02 -0600 Reply-To: "Robert K. Meyer" Sender: HPLX Mailing List From: "Robert K. Meyer" Subject: Re: DC ADAPTER Comments: To: Richard Millard MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit The power supply for the HP Omnibook 800's use the F1064B supply, 12V and reguated. Works with the LX with no modifications. Might check on ebay or perhaps a list member knows where you could find one. Bob Richard Millard wrote: > > My old dc-dc adapter I was using in the car for my HP200LX has died. I have > been looking for an alternate. I can find lots of 12V dc adapters with the > right kind of plugs to fit the LX. However, all of these adapters put out > unregulated voltage when the 12V setting is selected (usually about 14~14.5 > volts). I can't find an adapter which regulates the output when set for 12V. > > Does anyone know of a source for a regulated adapter for use in a car which > actually puts out 12V? > > Does anyone know if using a power source of 14~14.5V will damage the LX? > > _________________________________________________________________ > Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY http://w3.union-tel.com/~bmeyer/ The stone... Psa 118:22 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 23:12:42 +0530 Reply-To: Vivek Venugopalan Sender: HPLX Mailing List From: Vivek Venugopalan Subject: Re: ANN:Announcing the availability of DOCHTML MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hello all Further to this, I have also made the source code available. Please see the following URL http://sourceforge.net/project/showfiles.php?group_id=32363 Regards Vivek ----- Original Message ----- From: "Vivek Venugopalan" To: Sent: Sunday, August 05, 2001 6:22 PM Subject: ANN:Announcing the availability of DOCHTML > Hello all > I would like to Announce the availability of DOCHTML in source code form. > DOCHTML provides a way to convert memo editor files into HTML files. > > I have hosted it on sourceforge. The URL is http://dochtml.sourceforge.net > The latest version is Version 1.1 > > The application is available with source code under GPL. > > Suggestions, improvements? Please contact me at vivekv at > users.sourceforge.net or vivekv at yahoo.com > > Best Regards > Vivek > > > _________________________________________________________ > Do You Yahoo!? > Get your free @yahoo.com address at http://mail.yahoo.com > > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 13:54:48 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: TDMA and GSM MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Mon, 13 Aug 2001 09:20:40 +0200, Daniel Hertrich wrote: > Hi friends, Hello there > Here in Germany the cellular networks have their own "area codes", > so if you call a cell phone, say, in the E-Plus network, you always > have to dial a "0177" in front of the handset number, regardless, where > in Germany (or even in the world) the handset currently is. If you call +4790199462 you will get my phone regardless where I am in the world. Since the new T39m is a triband phone I could be home or having dinner with Avi when you call :-) > Every network has its own "area code" (actually in that case this > isn't an area code, because it is the same, whereever you are with your > phone). I gues +47 is what you call "area code". > Is it the same in other countries, or do cellular networks in other > countries seamlessly integrate with the wired network, using the area > codes of the "real" spatial areas? If you are witin Norway and call my cellphone you just have to call 90199462. The cellphone swithc knows where I am. If you are outside Norway then you call the norwegian swithc and the norwegian switch puts you through to my phone wherever I am. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 14:26:14 -0400 Reply-To: "M. Lennartz" Sender: HPLX Mailing List From: "M. Lennartz" Subject: Re: Ericssons new T39m and the Hplx MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable The original reply went to Josef only, so I repeat it: Josef Meyer wrote: > Only data > amount, not connection time will be charged. Therefore this service is > very good for interactive connection to a service, like WAP, email etc. > File transfer is evtl. more economic over a switched connection. E.g. > HSCSD (High speed circuit switched data) allows a switched connection > using up to 4*9600 bit/s time slots. > Hi Josef, the german provider E-Plus offers these high speed connections, but they are rather expensive. Conventional way: I can now download 30 KByte per minute (ca. 0,20 DM). If I remember right, I would pay 0,60 DM for the same amount using the new protocols (withing the first 100 KByte, for which E-Plus has a special price). Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 20:38:41 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: AT commands for Nokia phones MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, On Thu, 26 Jul 2001 16:09:25 -0500, "Stanley, John L." wrote: > Daniel... > It's Microsoft Windows HLP (helpfile) format. If you double-click the > file on a Windows machine, it opens the standard helpfile browser with > indexes, hotlinks, nicely formatted text and tables. Could someone repost the URL to this Nokia AT commands help file please? Due to a hard disk crash of my desktop computer I lost the file. I consider offering all these data sheets (Siemens, Nokia and hopefully Ericsson soon) on my homepage. Thanks a lot daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 20:41:38 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: Re: FLUFF: TDMA and GSM In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Le Mon, 13 Aug 2001 09:20:40 +0200 Daniel Hertrich a =E9crit: > Is it the same in other countries, or do cellular networks in other > countries seamlessly integrate with the wired network, using the area > codes of the "real" spatial areas? It is about the same in France=2E The general numbering scheme is=20 0x yy zz nn nn=20 (when you call from another country, you have to add the country code (33) and omit the first digit "0"=2E Then you must type +33 x yy zz zz zz) If x =3D 1 to 5, you have a wired line=2E It is localized, following this patern: =20 01 : Paris and neigbourgh 02 : North-West of France 03 : North-East 04 : South-East 05 : South-West =20 the "zz" number is the number of the central you are connected=2E Then it shows more precicely where you live=2E =20 =20 If x =3D 6, you have a cellular phone number=2E Each provider use some of the "yy" numbers =20 For example, Itineris/Orange uses : 07-08,54,70,=2E=2E=2E=2E SFR uses : 09-23,55=2E=2E=2E Bouygues uses : 60-66,67-68=2E=2E=2E (Sory, l don't have the complete list=2E=2E=2E :-) ) = =20 =20 To my knowledge, for none of the providers, the "yy" digits are based to the subscriber home localisation=2E =20 if x =3D 8, you have access to special services=2E 0800zznnnn are tolls free phones=2E=20 0836zznnnn are for surtaxed services=2E 0860zznnnn are for the national number of the ISP (always local paid)=2E Then, if you have a phone numbers like : 01 42 37 nn nn, you know that the subscriber lives near Paris (and probably near Antony) 06 60 zz nn nn, it is a Bouygues Telecom subscriber=2E=20 06 60 92 20 00 : The national number of the "Free=2Efr" ISP=2E About GSM frequencies, Itineris and SFR uses 900Mhz and Bouygues has been lanched exclusively in 1800 Mhz, but uses now a few 900 Mhs BTS=2E =20 =20 Jacques=2E ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 21:26:31 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: TDMA and GSM MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Martin, On Mon, 13 Aug 2001 13:54:48 -0400, Martin Bergvill wrote: > I gues +47 is what you call "area code". No. +47 is the country code. My number is +49 177 7955549 +49 is the country code (Germany) 177 is the area code (0177 within Germany if you leave away the +49) 7955549 is my participant number. Regarding the networks: +49 177 is always the German E-Plus network. (or 0177 from within Germany) +49 171 is always the German D1 network (or 0171) and so on. Since the networks have now too much participants to cover them all with 7-digit numbers, they now have additional area codes, for eample E-Plus has now +49 177 +49 178 D1 has +49 171 +49 170 +49 175 D2 has +49 172 +49 173 +49 174 And VIAG (yes, Stefan, I don't forget you ;-)) +49 179 (no additional area codes, AFAIK) But if you get a number from someone beginning with "0171" (or +49 171), you always KNOW he is a customer of the D1 network. > 90199462. The cellphone swithc knows where I am. If you are outside > Norway then you call the norwegian swithc and the norwegian switch puts > you through to my phone wherever I am. Yes, same here. 901 seems to be your network's area code (or only 90?), seems like cell phone netwprk provides love the "9". Sorry, folks, if this is off topic, but I find it very interesting to discuss that here! GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 13 Aug 2001 20:40:39 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: DC ADAPTER MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Daniel Hertrich wrote: > > > If a regulated supply is difficult to find a small motorcycle > > battery and a switch could be used. The switch would either > > charge the battery from the car or run the LX like this... / R1 ---O +-O O--/\/\/\/\-- LX | / Car ---O | O O------------ | | | | Motorcycle Battery > Generally a good idea, but be careful: If you switch the motorcycle > battery to the car battery the way you have drawed above, surely the > fuse will melt. I think in order to charge a battery, at least a currnt > limiting resistor would be needed, because an empty rechargeable looks > like a short-circuit to the charging source. > I can be wrong, but that's the way I recall it from my EE lectures in > university ;-) > And this resistor must stand quite a lot of current, you can't use such > a standrad 0.25W-resistor! It would be blown away like a fuse. Excellent point Daniel, shame on me for forgetting it. I have modified the picture (above) to show such a resister. Since power, in watts, is computed by P=I*I*R we can estimate the resister needed. Example a 10 ohm resister will cause about a 1.4A current flow (into a dead short) so 1.4*1.4*10 is almost 20 watts which is pretty big. A 50 ohm resister would cause .28A and up to 4 watts which is much easier to deal with. A 100 ohm would half the current and power again but lengthen charging times and might also be suitable for long duration trickle charging. So, if anyone gives this a try select a suitable resister based on charging time (the bigger R1 the lower current flow and the longer charge required) and max current and power acceptable. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 14 Aug 2001 10:29:14 +0100 Reply-To: Michael Lennartz Sender: HPLX Mailing List From: Michael Lennartz Subject: Re: (2) AT commands for Nokia phones In-Reply-To: Mime-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Hallo Daniel Hertrich schrieb am 13.08.2001: >Due to a hard disk crash of my desktop computer I lost the file. >I consider offering all these data sheets (Siemens, Nokia and >hopefully >Ericsson soon) on my homepage. Here it is: http://support.forum.nokia.com/support/at_command.zip -- Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net Fax: +49 89 244 34 52 57 -- Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net Fax: +49 89 244 34 52 57 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 14 Aug 2001 09:45:38 +0100 Reply-To: "Brown, William D" Sender: HPLX Mailing List From: "Brown, William D" Subject: Lotus Notes Synch MIME-Version: 1.0 Content-Type: text/plain I know this topic has appeared over the years, but has anyone ever made progress on synchronising Lotus Notes and the HP200? From searching the internet and the HPLX-L back lot all I've found was: 1. Russell Lewis (who has changed e-mail address so I've not managed to reach him) wrote about having a Lotusscript that could be run (provided you had the designer installed). This just uploaded from the HP200 appointment to Notes calendar. 2. Someone else (sorry I did not note who) used two commercial products to synchronise via Schedule+ It's bizarre having just got synchronisation sorted with Outlook thanks to Curtis Cameron, but our organisation is moving to Lotus Notes. William D.Ll.Brown ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 14 Aug 2001 05:43:26 -0700 Reply-To: patrick@west.net Sender: HPLX Mailing List Comments: RFC822 error: Incorrect or incomplete address field found and ignored. From: Patrick West Subject: Re: Lotus Notes Synch Comments: To: wdlb5359@glaxowellcome.co.uk Mime-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable William, Will the version of Notes you firm is going to synch with the older Lotus Organizer 2.x? If so 2.x can often be found cheaply, ebay for example has http://cgi.ebay.com/aw-cgi/eBayISAPI.dll?ViewItem&item=3D1264526500= which includes 2.1 There was even a $9.95 cd-rom version floating around on those= big shelves of software at the local office superstore, Fred= Meyer's, Kmart, Wallmart and such like places. Than this freebie from IBM will synch it with the 200lx= appointment and phone books. ftp://ftp.pc.ibm.com/pub/pccbbs/commercial_desktop/zq6t00a.exe =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D Baring that find out what the version of Notes will synch to, and= look for a linking product. On Tue, 14 Aug 2001 09:45:38 +0100, Brown, William D wrote: >I know this topic has appeared over the years, but has anyone= ever >made progress on synch ronising Lotus Notes and the HP200? > >>From searching the internet and the HPLX-L back lot all I've= found >>was: > >1. =A0 =A0 =A0Russell Lewis (who has changed e-mail address so I've= not >managed to reach him) wrote about having a Lotusscript that= could be >run (provided you had the designer installed). =A0This just= uploaded >from the HP200 appointment to Notes calendar. > >2. =A0 =A0 =A0Someone else (sorry I did not note who) used two= commercial >products to synchronise via Schedule+ > >It's bizarre having just got synchronisation sorted with= Outlook >thanks to Curtis Cameron, but our organisation is moving to= Lotus >Notes. > >William D.Ll.Brown > >** HPLX-L LIST Info at= http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- Patrick West, francis_patrick_west@yahoo.com on 08/14/2001 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 14 Aug 2001 08:42:13 -0500 Reply-To: John Musielewicz Sender: HPLX Mailing List From: John Musielewicz Subject: Virus MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Some butthole from this list keeps sending me a virus as an attachment. I am getting about two a day now. Be on the alert. If you get an email with HP listed as the sender with something concerning the LX (like LXDial) as the title of the attachment don't open it. Delete it. It is the jerk trying to infect you with a virus. I don't know which one it is all I do is delete the message. John ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 14 Aug 2001 13:31:05 -0700 Reply-To: Larry Mittell Sender: HPLX Mailing List From: Larry Mittell Subject: Re: Virus Comments: To: John Musielewicz In-Reply-To: <003401c124c7$1a311280$099ef3d8@bitstream.net> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii"; format=flowed Don't be too hard on him; it's probably not his fault. It sounds as though he's got a worm virus infecting his PC. He may not even realize it yet. Larry Mittell At 06:42 AM 8/14/01, John Musielewicz wrote: >Some butthole from this list keeps sending me a virus as an attachment. I am >getting about two a day now. Be on the alert. If you get an email with HP >listed as the sender with something concerning the LX (like LXDial) as the >title of the attachment don't open it. Delete it. It is the jerk trying to >infect you with a virus. I don't know which one it is all I do is delete the >message. > >John > >** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 14 Aug 2001 18:42:10 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: OT: Fluff: Linux questions MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Could some kind soul help me (in private email of course) with my new Linux installation? I just installed Red Hat Linux 7.1 as a dual boot with WindowsME, and although I am figuring out things as I go, I wish I could figure some things faster than others, mainly: 1-How to get Linux to recognize the dsl adapter (I found some information on the Web, but it asumes that Linux recognizes the adapter, which it does not). WindowsME uses a special connection program, not just a driver. 2-How to recognize other drives. I got the Linux installation to create a DOS partition, but neither Linux nor Windows sees it (the installation does). Also Linux doesn't see the main Windows partition, and Windows doesn't see the Linux drive. 3-How to access different display settings without running Xconfigurator everytime (it makes the system act weird if I do something wrong). I figure if I can access the Web via Linux, searching for information on how to set it up while I have it in front of me will be much easier, rather than going back to Windows each time I need to search the Web. Any help appreciated. Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 14 Aug 2001 07:06:55 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: Re: where is Mark in Seattle MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit > Maybe there are some trouble with the servers or something. > Regards > Martin Bergvill ,Narvik Norway thanks, Martin, he reads the list but hasn't replied - either he is on a loooooong holiday or he indeed has problems nat ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 15 Aug 2001 08:24:34 +0100 Reply-To: HP Staber Sender: HPLX Mailing List From: HP Staber Subject: Re: Virus MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable John, > Some butthole from this list keeps sending me a virus as an attachment. = I am > getting about two a day now. Be on the alert. If you get an email with = HP > listed as the sender with something concerning the LX (like LXDial) as = the > title of the attachment don't open it. Delete it. It is the jerk trying = to > infect you with a virus. I don't know which one it is all I do is = delete the > message. I have checked my outbox in case you did mean me - no messages of that kind have been sent by me. BTW I do all e-mail from my DOS based 96 meg DS HP200LX. It would be very unlikely if it came from me. HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 15 Aug 2001 09:06:34 +0200 Reply-To: daniel.hertrich@GMX.DE Sender: HPLX Mailing List From: Daniel Hertrich Subject: LXGLUC: any demand? MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Hi friends, I'd like to know if there is any demand here in such a software, before I invest too much power for such a project. It is the "successor" of DMSIM, please have a look at http://www.daniel-hertrich.de/dmsim if you don't know what I'm talking about, and it is only interesting for diabetics (or maybe for doctors having to do with diabetics). It is a diabetes tracking software for use on the palmtop and as the successor of DMSIM it is intended to be also usable WITHOUT the Camit software, which DMSIM has created files for. Please read the short description: /* LXGLUC Diabetes tracking software * * LXGLUC replaces the software DMSIM. It is an improved * version of DMSIM, but since it has non-Accutrend-DM- * specific features now, I decided to change its name. * * This software is especially developed to work on an * HP 100LX / 200LX palmtop, but works on every DOS * computer which has at least an 8086 processor, * 128kB RAM and 0.5 MB hard disk (or floppy). * It should also work within every DOS emulation * environment under Windows or other OSs. * * LXGLUC asks you to enter your blood glucose and several * other parameters and events (designed having the glucose * meter Accutrend DM in mind). LXCLUG saves these values * either in a file format which can be read by the Windows * software "Camit", version 3.0, by Roche Diagnostics, * or it can save the values in CSV format (comma seperated * values), so that you can read the data directly with every * spread sheet application and use it to draw diagrams or * whatever. * * Maybe I'll add a Lotus 123 compliant output format, so * one could directly process the data created by LXGLUC on the * palmtop with Lotus 123. (Lotus 123 cannot import CSV files, AFAIK) * * (c) 2001 by Daniel Hertrich. http://www.daniel-hertrich.de * */ GTX daniel -- http://www.daniel-hertrich.de/contact GMX - Die Kommunikationsplattform im Internet. http://www.gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 15 Aug 2001 06:07:34 -0400 Reply-To: MAnderson@SHIPLEY.COM Sender: HPLX Mailing List From: Michael Anderson Subject: Re: Lotus Notes Sync MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii Hi: I'm that 'someone else' ... who perservered and eventually got it going. What I used was XTNDConnectPC (www.extendedsystems.com) to go from Lotus Notes to Schedule+ (I've also done Notes<->Outlook with this product), and then IntelliSync for HPLX to sync Sched+ to the HP200LX. It works, but I had to be very careful with field matching and (in particular) repeat patterns for appointments. Mike ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 15 Aug 2001 14:19:45 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: Re: TDMA and GSM In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Le Mon, 13 Aug 2001 09:20:40 +0200 Daniel Hertrich a =E9crit: > the D and E networks only have these names in Germany, not in entire > Europe=2E But correct is that in entire Europe (like in most countries in > the world), GSM900 and GSM1800 is used=2E About cellular phones in USA, I just found an intersting faq at http://celdata=2Ecjb=2Enet/ Jacques=2E ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 15 Aug 2001 18:03:13 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Backup with automated dbcheck and alert MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, I'm running an automated dbcheck and then (if it succeeds) a backup from C: to A: ever night (by the appointment book). If dbcheck fails, it omits the backup and creates a txt file in the backup directoy whcih contains the text "backup failed due to db error". What I'm looking for is a way to let the palmtop notify me about the failed backup automatically if I switch it on the next morning. I think about something like the greeting message of the appointment book, containint not a palmtop tip, but the message "backup failed last night". Any ideas? TNX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 15 Aug 2001 23:20:25 +0530 Reply-To: Vivek Venugopalan Sender: HPLX Mailing List From: Vivek Venugopalan Subject: Feedback on DOCHTML MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hello all I would like to hear from users / developers of Dochtml. Any comments/suggestions folks? I would really like to hear something. Also, anybody in this list interested in doing a Japanese support? I have some exposure to Japanese software but dont have the linguistic skill. If there is interest in the same, can someone come forward ... regards Vivek _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 15 Aug 2001 22:24:26 -0500 Reply-To: theise@netins.net Sender: HPLX Mailing List From: Theodore Heise Subject: Re: Backup with automated dbcheck and alert Daniel Hertrich writes: > What I'm looking for is a way to let the palmtop notify me about the > failed backup automatically if I switch it on the next morning. > I think about something like the greeting message of the appointment > book, containint not a palmtop tip, but the message "backup failed last > night". > > Any ideas? How about writing a batch file that looks for the text file written if there was a failure, and echos it to the screen if it exists? You could run this from an appointment each morning. Ted ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 10:37:26 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Backup with automated dbcheck and alert MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Ted, On Wed, 15 Aug 2001 22:24:26 -0500, Theodore Heise wrote: > How about writing a batch file that looks for the text file written if > there was a failure, and echos it to the screen if it exists? You could > run this from an appointment each morning. Yes, that's a good idea! Thanks daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 10:37:27 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Good file compression program MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, thanks for all your valuable replies regarding this topic! On Sun, 12 Aug 2001 14:17:49 -0400, Steve Carder wrote: > I have used Jam to compress part of my palmtop's internal RAM drive. It worked > well and did not give me problems. It does slow down disk access and take up > some lower DOS RAM. I quit using it when I got a 64 Meg internal drive. I Yes, this issue with lower DOS RAM is a really bad problem, which I haven't thought of before. Since I don't have any spare RAM in my WWW/LX / Post/LX environment, this whole thing is not practical for me. I will try to save space and simply be happy withthe space I have. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 06:08:08 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: AT string for HSCSD on a Ericsson T39m MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi I have now gotten HSCSD to work with Ericsson T39m and Hplx/Www/Lx. The AT string I used was: Modeminit=ATZ+cbst=0,0,1;+chsn=4,2,0,12 Baud=38400 It gave me a 28.8 connection. I have not gotten all the other AT strings for the Ericsson T39m. I will try to get a hold of them too. I have not tested the Ericsson T39m that much but it seems that I can have about a 1m between Hplx and phone. This means less EMI trouble. I have also gotten the GPRS setup for Hp Jornada. But I have not gotten this to work with Hplx yet. But I am very close ÝISP_Gprs¨ Port=-1 OmniGo=1 PPP=1 Modem=1 Baud=38400 My_IP=0.0.0.0 DNS_IP=removed DNS2_IP=removed Script=CHAP_Script Login= ModemInit=AT+cgdcont=1,"IP,"internet" Dial=Special number from your mobilprovider *something* When I try a GPRS connection I get almost established. But it stops on Negotiating LCP arrow down up down up.... Cannot establish PPP Irda buffer overflow. I will try some more and see if I can resolve this. I am very close and a little bit exited. I will keep you all posted. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 12:25:09 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: AT string for HSCSD on a Ericsson T39m MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hallo Mertin, On Thu, 16 Aug 2001 06:08:08 -0400, Martin Bergvill wrote: > It gave me a 28.8 connection. I have not gotten all the other AT > strings for the Ericsson T39m. I will try to get a hold of them too. looking firward to get a link for my home page :-) Congratulations that you've got it to work! > I have not tested the Ericsson T39m that much but it seems that I can > have about a 1m between Hplx and phone. This means less EMI trouble. Very good! > I have also gotten the GPRS setup for Hp Jornada. But I have not gotten > this to work with Hplx yet. But I am very close Hey, great! Keep us informed! This seems to be the first time someone tries to go online with the HPLX via GPRS! A little step for you, but a big step for mankind! :-) GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 08:35:37 -0400 Reply-To: Steve Sender: HPLX Mailing List From: Steve Subject: Re: LXGLUC: any demand? Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Daniel Hertrich wrote: > * Maybe I'll add a Lotus 123 compliant output format, so > * one could directly process the data created by LXGLUC on the > * palmtop with Lotus 123. (Lotus 123 cannot import CSV files, AFAIK) Hi Daniel, 1-2-3 does accept CSV files. In the english version... /File, Import, Numbers. It does require non-numeric values to be "quoted" to work properly. Steve ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 09:28:00 -0400 Reply-To: MCHEM1@UCONNVM.UCONN.EDU Sender: HPLX Mailing List From: Al Kind Subject: Re: Good file compression program MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Thu, 16 Aug 2001 09:15:39 -0500 (EST) What is the "overhead" of the JAM driver? I seem to recall STACER was ~122k 05h38m12s ago ... On Thu, 16 Aug 2001, Daniel Hertrich wrote: > Hi friends, > > thanks for all your valuable replies regarding this topic! > > ... > Yes, this issue with lower DOS RAM is a really bad problem, which I > haven't thought of before. Since I don't have any spare RAM in my > WWW/LX / Post/LX environment, this whole thing is not practical for me. > I will try to save space and simply be happy withthe space I have. > > GTX > daniel > > -- > http://www.daniel-hertrich.de/contact > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > -- * Al Kind, 3113 Horsebarn Rd U-193, Storrs CT 06269-4193 USA * Phone:(860)486-6126 EFax:(413)826-8780 **TeamHP200LX** ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 13:55:06 +0000 Reply-To: fjkaufman@WORLDNET.ATT.NET Sender: HPLX Mailing List From: "F. Kaufman" Subject: Re: Backup with automated dbcheck and alert Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit > If dbcheck fails, it omits the backup and creates a txt file in the > backup directoy whcih contains the text "backup failed due to db > error". Set an early alarm that runs a dos program that opens and displays that file. And if you have a sucessful run, display "Success!" ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 19:56:22 +0100 Reply-To: hpstaber@COMPUSERVE.COM Sender: HPLX Mailing List From: HP Staber Subject: Re: AT string for HSCSD on a Ericsson T39m MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Martin, > > I have now gotten HSCSD to work with Ericsson T39m and Hplx/Www/Lx. I will need to replace my Nokia due to wear and tear soon. Relying on your market knowledge. What would be a good replacement under the following constraints (dual band is sufficient): - size (small) - battery life - IrDA HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 14:44:58 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: Card Reader for HPLX? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Does anyone know whether there is a program to read smart cards e.g. gsm-cards with the hplx via COM1? Uli ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 15:31:55 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: ricochet In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hey, Let's all chip in and buy ricochet! We can rename it to "Yet Anoter Wireless Network" (YAWN). We'll support only HPLX devices and all other handhelds running non-MS operating systems. Hal, watta y'say? We can use the profits to fund research into more features. Maybe we can revive the backlight project. http://dailynews.yahoo.com/h/zd/20010816/tc/ricochet_s_last_gasp_1.htm l ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 21:35:29 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: MUP: the movie, as if you are inside ;-) Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: quoted-printable I am currently just in front of the Notre Dame cathedral, in Paris, France. Well, you will say "what kind of interest, he plays the tourist in his own city"... . Yes, but at this time, just between me and the cathedral, there is a bi= g cinema screen... And several thousands of persons (4000, 5000 ?) are waiting, like me, for a movie. And guess what is the movie ? "The Hunchback of Notre Dame", version 1956, by Jean Delanoy, with Gina Lollobrigida and Antony Quinn... This projection is part of a cycle of "under the moon" projections showing movies at the same place they were shot. Whell, if Quasimodo exits from the screen and jumps to the towers, you will be the firsts informed ! ;-) Jacques. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 16:18:01 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: HSCSD on T39/R520/S40/SGH-Q100 AT strings MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi This is info I have collected about mobilphones and Hplx/HSCSD/Gprs Ericsson R520/T39: Analog V110 9.600 at+cbst=0,0,1;+chsn=1,1,0,4 at+cbst=71,0,1;+chsn=1,1,0,4 14.400 at+cbst=0,0,1;+chsn=2,1,0,12 at+cbst=75,0,1;+chsn=2,1,0,12 19.200 at+cbst=0,0,1;+chsn=3,2,0,12 at+cbst=79,0,1;+chsn=3,2,0,12 28.800 at+cbst=0,0,1;+chsn=4,2,0,12 at+cbst=80,0,1;+chsn=4,2,0,12 Gprs string at+cgdcont=1,"IP","internet" Ericsson R520/T39: Analog V110 9.600 at+cbst=0,0,1;+chsn=1,1,0,4 at+cbst=71,0,1;+chsn=1,1,0,4 14.400 at+cbst=0,0,1;+chsn=2,1,0,12 at+cbst=75,0,1;+chsn=2,1,0,12 19.200 at+cbst=0,0,1;+chsn=3,2,0,12 at+cbst=79,0,1;+chsn=3,2,0,12 28.800 at+cbst=0,0,1;+chsn=4,2,0,12 at+cbst=80,0,1;+chsn=4,2,0,12 Gprs string at+cgdcont=1,"IP","internet" Siemens S40:(not tested) Analog V110 9.600 at+cbst=0,0,1 at+cbst=71,0,1;+chsn=1,1,0,4 14.400 at+cbst=75,0,1;+chsn=0,1,0,12 19.200 at+cbst=79,0,1;+chsn=0,2,0,12 28.800 at+cbst=80,0,1;+chsn=0,2,0,12 Samsung SGH-Q100(Not tested) Analog V110 9.600 at+cbst=0,0,1 14.400 at+cbst=0,0,1 19.200 at+cbst=0,0,1 28.800 at+cbst=0,0,1 Nokia 6210/9210/CardPhone 2.0 Analog V110 9.600 +cbst=0,0,1;+chsn=1,0,0,0 +cbst=71,0,1;+chsn=1,0,0,0 14.400 +cbst=0,0,1;+chsn=2,0,0,0 +cbst=81,0,1;+chsn=2,0,0,0 19.200 +cbst=0,0,1;+chsn=3,0,0,0 +cbst=81,0,1;+chsn=3,0,0,0 28.800 +cbst=0,0,1;+chsn=4,0,0,0 +cbst=81,0,1;+chsn=4,0,0,0 43.200 +cbst=0,0,1;+chsn=6,0,0,0 +cbst=81,0,1;+chsn=6,0,0,0 I have tested/used the 6210 for a while and it worked well with the Hplx. Weblinks for more info: http://cellular.co.za/technologies/gprs/gprs-terminals.htm http://www.semiconductors.philips.com/comms/ http://www.mobilegprs.com/ I now have a T39 and it works. I have almost gotten it to work on Gprs. I get to Negotiating LCP Irda buffer overrun I will probably have a datacable that I can test soon. Not sure where the problem is, but I am working on it. Any progress will ofcourse be posted to the list. Daniel please feel free to put any of the above on your website. Please use my emailaddress:hplx@bergvill.com if you want to put my name there. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 16:18:04 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: AT string for HSCSD on a Ericsson T39m MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Thu, 16 Aug 2001 13:56:21 -0400 (EDT), HP Staber wrote: HP > > I have now gotten HSCSD to work with Ericsson T39m and Hplx/Www/Lx. > > I will need to replace my Nokia due to wear and tear soon. Relying on > your market knowledge. What would be a good replacement under the > following constraints (dual band is sufficient): > > - size (small) Nokia 6210 is "big" compared to the T39m. They are both laying on the table here. The size of the T39m is with antenna (yes I would have liked it to be internal) as tall as the 6210. But the T39m is lighter and smaller. If you put them besides each other:(I hope this shows alright) -- || _______ _______ |-----| | | | | |-----| |-----| |6210 | | T39 | |-----| | | | | |_____| |1 2 3| |4 5 6| |7 8 9| |* 0 #| ------- From top to bottom the T39 is right between row 1(1 2 3) and row 2 (4 5 6) on the 6210. But it has the antenna which is not really a problem. It has a smaller display, but it has three fonts which you can choose from. Not a problem. Also much better resolution. The 6210 is a gsm 900/1800/Hscsd phone. The T39 is newer and got HSCSD/Bluetooth/Hscsd/triband/voicerecord Well think I have written a message on what the T39 got. > - battery life The orginal LiPolymer battery on the T39 are supposed to have a standbyetime of 300 hours. I have not tested this to be true, but it got longer standby time than my 6210 thats for sure. > - IrDA EMIproblem seems to be "as good" with the Nokia. If you are in the market for a new phone (what phone do uou got now?) you should either wait for the 8310 (which has FM radio, but (probably) not all the features that the T39 got. The new Nokia 6310 is not that "new" as they hype it to be. Looks the same but got gprs and some new features ofcourse. Buy a Ericsson T39m. Soon you will have Gprs woking on it too. If you want you can sync it with Outlook and soon some online calender if you want. It also got Bluetooth and maybe you can get it to work with the Hplx in the future through BT. Price for a Nokia 6210 is now approx 3295,- Nok The Ericsson you can get for 3995,- Nok If you want a techphone then the T39 is what you want. I do not think that there are any other phones out there that has what you want and also are compatible with the Hplx. (And ofcourse are so well supported by me :-) Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 16:18:07 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: Good file compression program MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Thu, 16 Aug 2001 09:28:00 -0400, Al Kind wrote: > Thu, 16 Aug 2001 09:15:39 -0500 (EST) > > What is the "overhead" of the JAM driver? I seem to recall STACER was > ~122k I have Jam support two stacked drives and the overhead is 32.6kb Not sure how much it is for just one drive. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 22:46:32 +0100 Reply-To: remce@gofree.indigo.ie Sender: HPLX Mailing List From: "Richard E. McEvoy" Subject: OT Diet spam MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Hello folks, Have any of you had trouble deleting spam from "Secret Diet " ? The first message I got (on my desktop) was so big it took half a minute to download. It said "Lose 28lbs by September 15, Guaranteed.....etc." I did not reply or ask to be removed from their list, I just deleted it. The second, dated Sat. 11th, could not be deleted; the browser froze. Ctrl,Alt,Del froze the computer which had to be switched off. Several more attempts failed before one froze on the "End task" frame, and after the machine was switched off and restarted, the message was gone. Richard ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 21:20:21 -0700 Reply-To: D&A Software Support Sender: HPLX Mailing List From: D&A Software Support Subject: MM/LX Version 1.1 Uploaded. MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Dear Folks, This is to let you know that MM/LX (MindMap/LX) Version 1.1 was uploaded to our Website at http://www.dasoft.com. This version is full of goodies: Enhancements, new features, bug fixes. The details are on the website and you can go directly to the MM/LX Updates page at http://www.dasoft.com/MMLX/mmupd.htm. Both FTP sites have the new version in archive file mm.zip. I put direct links to the archive file in the MM/LX updates page mentioned above. Also, you HV users (and even non-HV users), your main page has been update (http://www.dasoft.com/indexHV.html) The price has changed. If you have a license for MM/LX please READ the information on the updates page - it may be worth your time.. Well, I hope you will like this version. We all think it is simply great! Oh, BTW - if you read this far down, then your prie is that the trial version has a new scheme, which allows you to save and do EVERYTHING you want, but only for 30 days. So I suppose sometime in mid September the orders will pour in, huh? ... Enjoy. Best regards, Avi Meshar D&A Software http://www.dasoft.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 17 Aug 2001 00:21:46 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: Good file compression program MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > What is the "overhead" of the JAM driver? I am going from distant memory, but around 35-40K. This is with setting optimized for less memory usage. If you go for faster and better compress= ion Jam uses something like 8K or 16K more memory. Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 17 Aug 2001 02:50:44 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: AT string for HSCSD on a Ericsson T39m MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Thu, 16 Aug 2001 12:25:09 +0200, Daniel Hertrich wrote: > Hallo Mertin, :-) Hello there.. > On Thu, 16 Aug 2001 06:08:08 -0400, Martin Bergvill wrote: > > > It gave me a 28.8 connection. I have not gotten all the other AT > > strings for the Ericsson T39m. I will try to get a hold of them too. > > looking firward to get a link for my home page :-) I can mail you the xls or you can use the message I posted here. The orginal xls has some about some Motorola's also I think. > Congratulations that you've got it to work! Well I have had some calls to Ericsson and also Telenor. I may have to call back to the Ericssonguy and tell him that he does not use the best AT string with his T39m. :-) The best should be the V110 string for 28.8. Will test it tomorrow. > > I have not tested the Ericsson T39m that much but it seems that I can > > have about a 1m between Hplx and phone. This means less EMI trouble. > > Very good! Tested it now with Ring.com. If I have the Hplx and the T39m about 5cm apart I get disturbance. Above that I get no disturbance at all.(!) I have to do some more field testing with HSCSD connections and see if Www/lx report any errors. But this looks promising. > > I have also gotten the GPRS setup for Hp Jornada. But I have not gotten > > this to work with Hplx yet. But I am very close > > Hey, great! Keep us informed! This seems to be the first time someone > tries to go online with the HPLX via GPRS! Hm I never thought of myself as a pioneer..but I guess I am :-) With a little more help from Andreas I am sure that I can report a success. > A little step for you, but a big step for mankind! :-) If we can get the Hplx to work with Gprs it will mean it can survive longer. I upgrade my phone often. About every year. I bought the 6210 last year approx this time of year. Next year I hope to report a successstory with a Hplx vs a UMTS phone :-) I think I am the only one here on the list with a Gprsphone? Regards -- Martin Bergvill ,Narvik Norway -- ___ Mar|in Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 17 Aug 2001 02:50:46 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: Card Reader for HPLX? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Thu, 16 Aug 2001 14:44:58 -0400, Ulrich Allen wrote: > Does anyone know whether there is a program to read > smart cards e.g. gsm-cards with the hplx via COM1? I know that there is a serialreader called Snappy or something that reads gsmcards. But I think it comes with winsoftware. Maybe only availible in Norway. Do search I do not have a weblink. I also have a serial 16c84(or something like that) reader/writer laying around here somewhere. I remember I used some dossoftware to upload something to it many years ago. I then used a old 286 laptop. I can see if the software is still around somewhere If you are interested. I think you can find schematic of these kinds of readers/writers on the web and maybe on the website of the magazine Elektor. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 17 Aug 2001 02:50:47 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: where is Mark in Seattle MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Tue, 14 Aug 2001 07:06:55 +0200, Nathalie Bugeaud wrote: > > Maybe there are some trouble with the servers or something. > > Regards > > Martin Bergvill ,Narvik Norway > > thanks, Martin, he reads the list but hasn't replied - either he is on a > loooooong holiday or he indeed has problems I got a email from him back in april. He wrote he was superbusy selling computers to people. And he only lurked on the list. I guess he is so behind now that he does not see these messages. I hope things work out.. Regards from Martin playing Styx on his new gadget (T39m) :-) ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 17 Aug 2001 03:47:26 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: Re: Card Reader for HPLX? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Thanks Martin for your infos concerning a cardreader. If you find that software it could help to solve my problem. Please send the software to my private email-adress: UliAllen@UliAllen.De At least I could give it a try. I am looking forward. Uli ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 17 Aug 2001 01:06:40 -0700 Reply-To: surf.lx@JUNO.COM Sender: HPLX Mailing List From: Surfer Surfer Subject: FLUFF: FLAME BAIT: WAS: Re: where is Mark in Seattle MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Maybe: 1. with all of your personalized comments and vast knowledge about the laws in The United States, and how and why and where and when and who (the 4 w's) accepts cash, cashiers check not personal checks ... 2. who should, could, must file for income tax, and what is and how is taxable ? 3. on who exports what to where, why, when, how much ? 4. identifying the people who are in it for the hobby OR a profit making enterprise ? 5. Even railroading knowledgeable, technical people turn a deaf ear to this list ? 6. and the federales without wanting to have wasted their time scouring "this HPLX-L list" "looking for spies ?" and "non existent secret messages ?" e.g.(Example Given -may have nothing to do with this message): The Wronged Man: C.I.A. Officer Mistaken for Spy Down the Street By JAMES RISEN and DAVID JOHNSTON http://www.nytimes.com/2001/08/11/national/11SPY.html have turned him into an escape goat, to justify their time and budget spend here ? doesn't who gets ruined financially, socially ... 7. Soliciting amorous letter, and how great your sexual life is, then sending flames, and also later claiming "Nathalie, who never ate supper before saying grace!" and how sensuous are French women (do not bathe but use perfume to cover their stink ? ). Definitely there is a skunk here. And is it always a coincidence that your postings on this list coincide with the same monthly phases of the moon ? A mailing list is usually a microcosm of the society at large, and we all know (the ones who know are always bothered by the ones who think they know) how a losers, snitches (AKA Judas), instigators (which you already have admitted being an instigatrice) stop the productive member(s) of society to achieve greater good, and are turned off by the ... et cetera, et cetera, et cetera ... N.B. (Nota Bene): Any message sent to me, will and could be published in any form I see fit. I truly believe in the U.S.C. 5.552 and the First Amendment (Now translate that Nathalie!) Rule No. 1: Never ask a question that you don't already know the answer (attorneys at law speak) Rule No. 2: Never ask a question that you may not be able to handle the answer. The evidence is the archives, I don't need to keep any of such -Have a nice day ! On Tue, 14 Aug 2001 07:06:55 +0200 Nathalie Bugeaud writes: > > Maybe there are some trouble with the servers or something. > > Regards > > Martin Bergvill ,Narvik Norway > > thanks, Martin, he reads the list but hasn't replied - either he is > on a > loooooong holiday or he indeed has problems > > nat ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 00:06:42 +1000 Reply-To: Russell Hemery Sender: HPLX Mailing List From: Russell Hemery Subject: Re: Good file compression program In-Reply-To: <200108170421.AAA06831@siaar1ab.compuserve.com> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" At 12:21 AM 17/08/01 -0400, you wrote: >> What is the "overhead" of the JAM driver? > >I am going from distant memory, but around 35-40K. This is with setting >optimized for less memory usage. If you go for faster and better compression >Jam uses something like 8K or 16K more memory. From the manual its 32k default memory used with 8k clusters and can be reduced to 24k if you specify 4k clusters when running jcreate. Hope this is of help Russell ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 17 Aug 2001 14:51:13 +0000 Reply-To: fjkaufman@WORLDNET.ATT.NET Sender: HPLX Mailing List From: "F. Kaufman" Subject: Re: MUP: the movie, as if you are inside ;-) Comments: To: Jacques Belin MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit > And guess what is the movie ? "The Hunchback of Notre Dame", version > 1956, by Jean Delanoy, with Gina Lollobrigida and Antony Quinn... Dare I admit to having seen it when it was first released. (G) Oh, and I saw it in just a classic place - Da Bronx, NY. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 17 Aug 2001 11:16:15 -0400 Reply-To: MCHEM1@UCONNVM.UCONN.EDU Sender: HPLX Mailing List From: Al Kind Subject: Fwd: FLUFF: FLAME BAIT: WAS: Re: where is Mark in Seattle MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable 08/17/01 11:15 am I HPLX-L subscribers feel the need to "feed this FLAME", please do so in private, not on HPLX-L Cheers...AJKind --- begin of forwarded message --- Date: Fri, 17 Aug 2001 01:06:40 -0700 From: Surfer Surfer Subject: FLUFF: FLAME BAIT: WAS: Re: where is Mark in Seattle To: HPLX-L@UCONNVM.UCONN.EDU Maybe: 1. with all of your personalized comments and vast knowledge about the laws in The United States, and how and why and where and when and who (the 4 w's) accepts cash, cashiers check not personal checks ... -- * Al Kind, 3113 Horsebarn Rd U-193, Storrs CT 06269-4193 USA * Phone:(860)486-6126 EFax:(413)826-8780 **TeamHP200LX** ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 16:24:51 -1000 Reply-To: scott wormser Sender: HPLX Mailing List From: scott wormser Subject: Re: HPLX-L to Rexx been thinking of getting a rexx anyone recommend a model to get and price? also any program's that transfer hplx phone to rexx?? thanks scotty2u@juno.com ________________________________________________________________ GET INTERNET ACCESS FROM JUNO! Juno offers FREE or PREMIUM Internet access for less! Join Juno today! For your FREE software, visit: http://dl.www.juno.com/get/tagj. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 01:04:46 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: SecureDevice - Double Paranoia MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Secure Device users, just how paranoid are you? :-) If you think someone's out to get your data here's a way to increase its protection; add another SecDev drive whose encrypted file is in your first SecDev drive. Example: device=secdev.sys c:\secdev01.!@# device=secdev.sys g:\secdev02.!@# The 1st line establishes my main SecDev drive which becomes my G: drive. Note the 2nd line says the encrypted file (secdev02.!@#) is in the G: drive. That becomes my H: drive. To access H: files I must login to G: before I can login to H:. The drives can (and should) have different passwords. Yes H: is slow(er). All the data has to be encrypted/decrypted twice. The 2nd SecDev drive also uses @6.5k more storage. Is this practical? You decide; after verifying it works I deleted my 2nd SecDev drive. It worked but I didn't reall need that extra layer of security. I assume you can add addition layers of nested SecDev drives but I didn't test that. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 02:34:50 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: HPLX-L to Rexx MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit scott wormser wrote: > been thinking of getting a rexx anyone recommend a model to get and > price? > also any program's that transfer hplx phone to rexx?? I assume you mean Rex, the tiny pda, not Rexx. Rexx with 2 Xs is a very nice interpreted language. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 05:38:30 +0100 Reply-To: Chris Randle Sender: HPLX Mailing List From: Chris Randle Subject: FLUFF: MUP: the movie, as if you are inside ;-) MIME-Version: 1.0 In message , Jacques Belin writes >I am currently just in front of the Notre Dame cathedral, in Paris, >France. >And guess what is the movie ? "The Hunchback of Notre Dame", version >1956, by Jean Delanoy, with Gina Lollobrigida and Antony Quinn... > >This projection is part of a cycle of "under the moon" projections >showing movies at the same place they were shot. Thanks for the great tip. Looking forward to "Titanic". ;-) -- Chris Randle - Amethyst Logic ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 12:04:22 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: Re: FLUFF: MUP: the movie, as if you are inside ;-) In-Reply-To: <5$3nMAAGFff7Iwhz@amlog.demon.co.uk> MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Le Sat, 18 Aug 2001 05:38:30 +0100 Chris Randle a =E9crit: > Thanks for the great tip=2E Looking forward to "Titanic"=2E ;-) Well, with a litlle luck, there will be a GSM base station on the iceberg ! ;-) Jacques=2E ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 15:45:59 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: SecureDevice - Double Paranoia MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Russel, On Sat, 18 Aug 2001 01:04:46 +0000, Russel Brooks wrote: > If you think someone's out to get your data here's a way to > increase its protection; add another SecDev drive whose > encrypted file is in your first SecDev drive. Very interesting experiment! Hopefully the sevdev encryption mechanism doesn't work similar to ROT13! ;-) GTX daniel (not (yet) a secdev user) -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 15:46:00 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: HPLX-L to Rexx MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Scott, On Thu, 16 Aug 2001 16:24:51 -1000, scott wormser wrote: > been thinking of getting a rexx anyone recommend a model to get and > price? > also any program's that transfer hplx phone to rexx?? The only Rex that's synchronizable with the LX is the REX-3 (or Rex 3000) (this one with 256kB RAM). Please have a look at http://www.daniel-hertrich.de/rexsync to see what's possible and what not. Regading appointment synchronization: Chris Lott, what's the current state of your software decelopment? GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 15:46:01 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: AT string for HSCSD on a Ericsson T39m MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Martin, On Fri, 17 Aug 2001 02:50:44 -0400, Martin Bergvill wrote: > I can mail you the xls or you can use the message I posted here. The > orginal xls has some about some Motorola's also I think. The XLS, Please! :-) GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 22:46:33 +0800 Reply-To: Adrian Ho Sender: HPLX Mailing List From: Adrian Ho Subject: Re: HPLX-L to Rexx In-Reply-To: ; from daniel.hertrich@GMX.DE on Sat, Aug 18, 2001 at 03:46:00PM +0200 Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii On Sat, Aug 18, 2001 at 03:46:00PM +0200, Daniel Hertrich wrote: > The only Rex that's synchronizable with the LX is the REX-3 (or Rex > 3000) (this one with 256kB RAM). Do you mean that the other models lack the sync tools, or that some other factor (eg. current draw) makes in-slot syncing impossible? - Adrian ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 00:07:32 +0530 Reply-To: Vivek Venugopalan Sender: HPLX Mailing List From: Vivek Venugopalan Subject: Source for DOS software collection MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hello folks Stumbled on a nice collection of MSDOS freeware tools. Take a look at http://master.swlibero.org/~daniele/dos/valuedos.html Regards Vivek _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 23:51:51 +0200 Reply-To: furlan@gmx.net Sender: HPLX Mailing List From: "Dr. Werner Furlan" Organization: OE9FWV Subject: Fluff: Re: SecureDevice - Double Paranoia MIME-Version: 1.0 Content-type: text/plain; charset=US-ASCII Content-transfer-encoding: 7BIT hi Russel, On 18 Aug 2001, at 1:04, Russel Brooks wrote: > > If you think someone's out to get your data here's a way to > increase its protection; add another SecDev drive whose > encrypted file is in your first SecDev drive. > this looks even more secure than applying ROT13 twice on a file ;-) cheers, Werner OE9FWV -- Powered by Pegasus Mail - free at http://www.pmail.com Homepage: http://www.qsl.net/oe9fwv SMS: +436646340014@text.mobilkom.at ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 23:51:51 +0200 Reply-To: furlan@gmx.net Sender: HPLX Mailing List From: "Dr. Werner Furlan" Organization: OE9FWV Subject: Bgfax with Ericson SH 888 ? MIME-Version: 1.0 Content-type: text/plain; charset=US-ASCII Content-transfer-encoding: 7BIT hello, a friend of me has tried to use Bgfax with his Ericson SH 888 phone. It did not work and he now wants to send the phone to me for a try. The phone has a modem built in and he tried it with the data cable, not IRDA of course. Has anybody used this mobile phone for faxing with the palmtop? Are there any initialization commands necessary? thank you for reading and any hints Werner -- Powered by Pegasus Mail - free at http://www.pmail.com Homepage: http://www.qsl.net/oe9fwv SMS: +436646340014@text.mobilkom.at ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 18 Aug 2001 16:06:35 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Off Topic: Reg Exp help Comments: cc: omnibook@elektro.cmhnet.org MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii This is mostly for the unix and regular expression inclined ... the rest of you can just hit delete (with my apologies). I have to filter a text file using grep (or sed) and need to delete all lines that contain one or less of a certain delimiter. For example, aaa|bbb|ccc xxx|zzz 333 111|222|444|qqq with the vertical bar "|" as the delimiter, only the first and last lines should be retained: aaa|bbb|ccc 111|222|444|qqq Does anyone know the regular expression for sed or grep that will match this? Many thanks for an answer (simplest is best) ... my head is sore from beating the monitor. - Longden PS - I know Rexx and Korn shell and other languages can do this easily in a loop. I need to do it using grep or sed (NOT awk). ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 05:31:19 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: adapter fault causes buzzing/crash MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit due to increased summer temperature and/or old age my adapter shows output 14.8V which caused my LX to buzz needing several ctrl/shift/on to come alive. It also corrupted files needing further boots. Did anyone have the "buzzing" noise and similar consequences? also, my PC seems to have a virus - i can't get past the " Fatal Error 0E at 0028:00CA0F9E " or at 0028:00CB77CC in VxD-- VKD (01) in windoze98. The "no response" items are Explorer and Vshwin32. I tried F8 and 'sans echec' (safe mode?) but it just locks up. do i need to format C:\ or a new puter altogether? >and how sensuous are French women (do not bathe but use perfume >to cover their stink.. as to Frenchwomen smelling . . wasn't John F infatuated by Marilyn just because of 'That' Smell? Nathalie ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 02:05:02 -0400 Reply-To: WEB Sender: HPLX Mailing List From: WEB Subject: Re: adapter fault causes buzzing/crash MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Nathalie, > due to increased summer temperature and/or old age my adapter shows output > 14.8V which caused....buzz needing..... Purchase a new adapter! I wouldn't use this one. > Did anyone have the "buzzing" noise and similar consequences? Does your 200LX still buzz while on batteries. If not you may escaped expensive repair costs. If I were you I would purchase a four pack of NiMH batteries and charger. This way you could carry the spares around with you to use on those heavy use days when one set runs low. > also, my PC seems to have a virus - i can't get past the " Fatal Error 0E at > 0028:00CA0F9E " or at 0028:00CB77CC in VxD-- VKD (01) in windoze98. Fatal exception errors are codes that are returned by a program in the following cases: Access to an illegal instruction has been encountered Invalid data or code has been accessed The privilege level of an operation is invalid Error: 14 (0E): Page Fault The Page Fault interrupt allows the operating system to implement virtual memory on a demand-paged basis. An interrupt 14 usually is issued when an access to a page directory entry or page table with the present bit set to 0 (Not present) occurs. The operating system makes the page present (usually retrieves the page from virtual memory) and re-issues the faulting instruction, which then can access the segment. A page fault also occurs when a paging protection rule is violated (when the retrieve fails, or data retrieved is invalid, or the code that issued the fault broke the protection rule for the processor). In these cases the operating system takes over for the appropriate action. You need to perform a clean boot. Can you get Windows 98 up long enough to run MSCONFIG? Once you run this program you will see a number of tabs across the top below the menu. The one you need be concerned with is the General tab. Choose selective startup and disable all the checked items to get a clean boot. You don't need a new computer. These VXD files are use by third party manufacturer to load hardware and software drivers. All that has happened is a driver for one of your devices has become corrupted and needs to reloaded. Here is a good place to start looking for a solution: http://support.microsoft.com/support/kb/articles/Q192/9/26.ASP Let me know if I can be or any furthur assistance. > >and how sensuous are French women (do not bathe but use perfume > >to cover their stink.. > > as to Frenchwomen smelling . . wasn't John F infatuated by Marilyn just > because of 'That' Smell? What is this all about? Some people need to get a life! Anytime for assistance, William E. Blankenship ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 02:15:48 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Re: HPLX-L to Rexx Comments: To: Adrian Ho MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Adrian Ho" > On Sat, Aug 18, 2001 at 03:46:00PM +0200, Daniel Hertrich wrote: > > The only Rex that's synchronizable with the LX is the REX-3 (or Rex > > 3000) (this one with 256kB RAM). > Do you mean that the other models lack the sync tools, or that some > other factor (eg. current draw) makes in-slot syncing impossible? He means the former. The Rex 3 is the only one supported at this time. Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 11:23:10 +0100 Reply-To: Michael Lennartz Sender: HPLX Mailing List From: Michael Lennartz Subject: Re: adapter fault causes buzzing/crash In-Reply-To: <000f01c12864$1a981660$a521fac1@oemcomputer> Mime-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable (The reply-address was wrong, so I send it again.) Hallo Nathalie, I don't know, if you have a virus, but I see, that you use VSHIELD. On some machines a virus scanner (Norton AV) destroys the OS after some time. I use DOS-F-PROT for manual scanning. If the v-scanners don't caution, you should simple re-install win98. Some win98-machines need this "maintenance" once a year. Start setup.exe on the Win-CD or the win98-folder, if you have copied the CD on your computer. This procedure helps in most cases. Don't worry, it keeps the installed software in order. -- Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net Fax: +49 89 244 34 52 57 Nathalie Bugeaud schrieb am 19.08.2001: >also, my PC seems to have a virus - i can't get past the " Fatal >Error 0E at >0028:00CA0F9E " or at 0028:00CB77CC in VxD-- VKD (01) in >windoze98. The "no >response" items are Explorer and Vshwin32. I tried F8 and 'sans >echec' (safe >mode?) but it just locks up. do i need to format C:\ or a new puter >altogether? -- Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net Fax: +49 89 244 34 52 57 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 12:01:22 +0200 Reply-To: Josef Meyer Sender: HPLX Mailing List From: Josef Meyer Subject: Re: Bgfax with Ericson SH 888 ? Comments: To: "Dr. Werner Furlan" MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Werner, Dr. Werner Furlan wrote: > > a friend of me has tried to use Bgfax with his Ericson SH 888 phone. > It did not work and he now wants to send the phone to me for a try. > The phone has a modem built in and he tried it with the data cable, > not IRDA of course. As far as I know the SH888 uses the IRDA protocol also via cable. No AT strings in asynchroneous direct transmission can be detected. Instead of sending direct strings via serial cable as normal, the IRDA protocol is transmiited via cable instead over infrared. Because BGFAX only allows the "normal" way of controlling modems via serial port, SH888 is useless. > Has anybody used this mobile phone for faxing with the palmtop? > Are there any initialization commands necessary? The only way to use the SH888 is to buy a PCMCIA modem that supports the SH888 (e.g. DC23-V4 from Ericsson or the PSION Goldcard Global). This will work, but is quite expensive. I believe for the price of a PCMCIA modem card you better buy WWW/LX and use email instead of FAX. WWW/LX works with the infrared port of SH888 Josef Meyer ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 16:45:39 +0200 Reply-To: Jacques Belin Sender: HPLX Mailing List From: Jacques Belin Subject: Re: AT commands for Nokia phones In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: quoted-printable Le Mon, 13 Aug 2001 20:38:41 +0200 Daniel Hertrich a =E9crit: > Could someone repost the URL to this Nokia AT commands help file > please? > Due to a hard disk crash of my desktop computer I lost the file=2E > I consider offering all these data sheets (Siemens, Nokia and hopefully > Ericsson soon) on my homepage=2E About Siemens phone, there are two files : http://www=2Emy-siemens=2Ecom/external/tt/hq/mw/hd/hd/p35/s35i_c35i_m35i_mod= em_commandset_v01=2Epdf for the supported standard AT commands, and http://www=2Emy-siemens=2Ecom/external/tt/hq/mw/hd/hd/p35/s35i_c35i_m35i_atc= _commandset_v01=2Epdf for the GSM AT command set About Ericsson phone, the only place I founded some documentation (a few mon= ths ago) was in their "developper zone", which requires (free) registration before access=2E So If there are some urls (for the R320s, for example : http://www=2Eericsson=2Ecom/mobilityworld/developerszonedown/downloads/docs/= r320/R320s_WP_R1A=2Epdf ) I don't think it is "legal" to post the URL of the file on your site=2E=2E= =2E Anyway, there is was only a summary of the commands, without detailed syntaxes=2E You must read the Ýmore complete¨ Siemens docs, and try for yourself to see which commands are compatible=2E=2E=2E Jacques=2E ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 21:09:49 +0530 Reply-To: Vivek Venugopalan Sender: HPLX Mailing List From: Vivek Venugopalan Subject: Re: Off Topic: Reg Exp help Comments: To: Longden_Loo@CANDLE.COM MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Longden Can you use cut? If so then just cut for Field 3 with the delimiter set. If it returns a valid value then you need that line otherwise skip it. if Ý -s cut -f3 -d"|" ¨ Vivek ----- Original Message ----- From: "Longden Loo" To: Sent: Sunday, August 19, 2001 4:36 AM Subject: Off Topic: Reg Exp help > This is mostly for the unix and regular expression inclined ... the rest of > you can just hit delete (with my apologies). > > I have to filter a text file using grep (or sed) and need to delete all > lines that contain one or less of a certain delimiter. > > For example, > > aaa|bbb|ccc > xxx|zzz > 333 > 111|222|444|qqq > > with the vertical bar "|" as the delimiter, only the first and last lines > should be retained: > > aaa|bbb|ccc > 111|222|444|qqq > > Does anyone know the regular expression for sed or grep that will match > this? Many thanks for an answer (simplest is best) ... my head is sore > from beating the monitor. > > - Longden > > PS - I know Rexx and Korn shell and other languages can do this easily in a > loop. I need to do it using grep or sed (NOT awk). > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 16 Aug 2001 09:27:59 -0700 Reply-To: LLoo@WORLDNET.ATT.NET Sender: HPLX Mailing List From: Longden Loo Subject: Re: Off Topic: Reg Exp help In-Reply-To: <004101c128c5$346d6f20$0201a8c0@ntbox> MIME-Version: 1.0 Content-type: text/plain; charset=US-ASCII Content-transfer-encoding: 7BIT Thanks Vivek (and all others who responded). Acutally, I had been using "cut", but this required a loop to read each line, spawning a shell to echo each line to process the cut command and took just too long. Using the proposed solution ... grep "|.*|" reduced the time from something like 20 secs to 2 secs. Thanks again to all. - Longden On 19 Aug 2001, at 21:09, Vivek Venugopalan wrote: > Longden > Can you use cut? If so then just cut for Field 3 with the delimiter > set. > If it returns a valid value then you need that line otherwise skip it. > > if Ý -s cut -f3 -d"|" ¨ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 21:28:39 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: HPLX-L to Rexx MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Adrian, On Sat, 18 Aug 2001 22:46:33 +0800, Adrian Ho wrote: > Do you mean that the other models lack the sync tools, or that some > other factor (eg. current draw) makes in-slot syncing impossible? Power is not the problem, the REX is simply an SRAM (or the newer model a flash) card for the LX. Not ATA-compatible, probably, so you canot access it like a DOS drive. But Mack is the expert here. He wrote the software to write data to the REX. Chris Lott develops the converter software. The data structure in the newer Rexs is totally different to the Rex 3 data structure, and since Chris isn't an old guy who doesn't have anything else to do, he cannot care about all these different data structures ;-) We can be happy that he managed all the work to explore the Rex 3 data structure. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 15:45:47 -0500 Reply-To: Chris Lott Sender: HPLX Mailing List From: Chris Lott Subject: Re: Bgfax with Ericson SH 888 ? Comments: To: meyerj@SWISSONLINE.CH In-Reply-To: <200108191001.f7JA1Lk13121@mail.swissonline.ch> from "Josef Meyer" at Aug 19, 2001 12:01:22 PM MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit > As far as I know the SH888 uses the IRDA protocol also via cable. No AT > strings in asynchroneous direct transmission can be detected. Instead > of sending direct strings via serial cable as normal, the IRDA protocol > is transmiited via cable instead over infrared. Your message was very enlightening! I have the CF888, which I believe to be similar to the SH888. I have attempted to use the serial cable yet, but I had mistakenly believe it to have an internal modem-like interface. I was so suspicious of you comment that I dug out my manual, and sure enough, it sure seems like you are correct. Well, that still doesn't exclude using my phone/cable with my laptop, since some Windows software was provided with the phone. But it appears cable operation with the HP200 is out. > The only way to use the SH888 is to buy a PCMCIA modem that supports > the SH888 (e.g. DC23-V4 from Ericsson or the PSION Goldcard Global). > This will work, but is quite expensive. I happen to have the DC12 PCMCIA card, which is a predecessor to the DC23. I used it extensively with my first phone, a CF388. If it is capable of connection to the 888, I don't know how I would accomplish this. Perhaps through a special adaptor cable? If you know of such a connector, please advise. It would be nice to have in an emergency. Thanks, -Chris Lott -- ************************************************************************ R. Christopher Lott, P.E. rclott@ro.com Alpha Beta Technologies, Inc. 3112 12th Ave S.W. PHONE: 256-534-9067 Huntsville, Alabama 35805 FAX: 256-534-9069 ************************************************************************ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 22:31:43 -0700 Reply-To: DM <74737.221@compuserve.com> Sender: HPLX Mailing List From: DM <74737.221@COMPUSERVE.COM> Subject: Fw: Energizer Li battery... MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit > Hello, all > > Been a long time since I have needed this list.... > But it is always good to read what others are doing. > > My question is.... > > My favorite source of AA li energizer batteries no longer has them...;. > > Home depot at 4.19 a pair says they no longer stock them. > > Anyone else know of a reasonable source for these? > > I've seen them at Radio shack and other stores for around 10bucks a pair (!) > > Thanks > > > dave ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 19 Aug 2001 23:31:12 -0600 Reply-To: "Robert K. Meyer" Sender: HPLX Mailing List From: "Robert K. Meyer" Subject: Re: Fw: Energizer Li battery... Comments: To: DM <74737.221@compuserve.com> MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Seems like I saw a pack of 4 at the Laramie Super Walmart for about 10 bucks. As there are several battery displays, you may find them on one out of five displays. Bob DM wrote: > > > Hello, all > > > > Been a long time since I have needed this list.... > > But it is always good to read what others are doing. > > > > My question is.... > > > > My favorite source of AA li energizer batteries no longer has them...;. > > > > Home depot at 4.19 a pair says they no longer stock them. > > > > Anyone else know of a reasonable source for these? > > > > I've seen them at Radio shack and other stores for around 10bucks a pair > (!) > > > > Thanks > > > > > > dave > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY http://w3.union-tel.com/~bmeyer/ The stone... Psa 118:22 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 08:07:11 +0200 Reply-To: Josef Meyer Sender: HPLX Mailing List From: Josef Meyer Subject: Re: Bgfax with Ericson SH 888 ? Comments: To: Chris Lott MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Chris Lott wrote: > > I happen to have the DC12 PCMCIA card, which is a predecessor to the > DC23. I used it extensively with my first phone, a CF388. If it is > capable of connection to the 888, I don't know how I would accomplish > this. Perhaps through a special adaptor cable? If you know of such > a connector, please advise. It would be nice to have in an emergency. I don't believe that you will find a cable to connect the DC12 PCMCIA card with a SH888 mobile phone. As far as I remember, the CF388 is 5V technology, whereas the SH888 is 4V technology. I know that Ericsson has released the DC23 modem for the 388 serieas and the later DC23V4 for the 6xx/7xx/8xx series. The DC23 (without the 4V suffix) hasn't worked with the 6xx/7xx/8xx models, even with the correct cable, I have tried it some years ago. I think the situation is the same with the DC12. Josef Meyer ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 09:13:38 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Bgfax with Ericson SH 888 ? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Chris On Sun, 19 Aug 2001 15:45:47 -0500, Chris Lott wrote: > Your message was very enlightening! I have the CF888, which I believe > to be similar to the SH888. I have attempted to use the serial cable > yet, but I had mistakenly believe it to have an internal modem-like > interface. I was so suspicious of you comment that I dug out my > manual, and sure enough, it sure seems like you are correct. Well, > that still doesn't exclude using my phone/cable with my laptop, since > some Windows software was provided with the phone. But it appears > cable operation with the HP200 is out. Not entirely: I believe WWW/LX can use the IrDA protocol over the cable with a special combination of options in www.cfg (IR=x and Port=y, for the correct x and y values please ask Avi) GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 00:30:01 -0700 Reply-To: Fryday Sender: HPLX Mailing List From: Fryday Subject: Mind Map LX MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Avi, Mind Map LX rocks! I'll certainly be registering and told another friend about it. BTW, his vision is going, so he'd love a bigger font (doesn't matter to him if he has to scroll around a bit more) Also been experiencing some strange file corruption, though, but still trying to reproduce. Only one feature I would truly love to see in this program: the ability to link to child. Yep, would be tricky to show all those links across the board, so here's how I would propose to do it: give a tell-tale sign that there are links to other children (similar to the idea of the "+" when there are collapsed children), and only show the links to other children when that one child is highlighted. When the children is not highlighted, only show the tell-tale sign. Thanks for a great program! A bientot, Philippe ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 00:44:56 -0700 Reply-To: Fryday Sender: HPLX Mailing List From: Fryday Subject: Re: Mind Map LX MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Of course, I meant "the ability to link two children". Yes, I saw on the site that it is possible to do this by having a child be in a different mind map, and then linking two parents to it, but that has the effect of hising that child from the main mindmap. What I find amzingly useful is the capability to see and establish right on the main mind map those child-child connections I find between ideas (and not just a parent-child). Thanks again! Philippe ----- Original Message ----- From: "Fryday" To: Sent: Monday, August 20, 2001 12:30 AM Subject: Mind Map LX > Avi, > > Mind Map LX rocks! I'll certainly be registering and told another friend about it. BTW, his vision is going, so he'd love a > bigger font (doesn't matter to him if he has to scroll around a bit more) > > Also been experiencing some strange file corruption, though, but still trying to reproduce. > > Only one feature I would truly love to see in this program: the ability to link to child. Yep, would be tricky to show all > those links across the board, so here's how I would propose to do it: give a tell-tale sign that there are links to other > children (similar to the idea of the "+" when there are collapsed children), and only show the links to other children when > that one child is highlighted. When the children is not highlighted, only show the tell-tale sign. > > Thanks for a great program! > > A bientot, > > Philippe > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 10:38:20 -0600 Reply-To: "Batson, Dale N" Sender: HPLX Mailing List From: "Batson, Dale N" Subject: Re: Energizer Li battery... MIME-version: 1.0 Content-type: text/plain Content-transfer-encoding: 7BIT I've never ordered from them, but Omega Man sells Energizer Lithium AA batteries @ $8.95 per two pak. http://www.omegamanenterprises.com/energizerlithiumaabatteries.htm -----Original Message----- From: Robert K. Meyer Ýmailto:bmeyer@UNION-TEL.COM¨ Sent: Sunday, August 19, 2001 11:31 PM To: HPLX-L@UCONNVM.UCONN.EDU Subject: Re: Fw: Energizer Li battery... Seems like I saw a pack of 4 at the Laramie Super Walmart for about 10 bucks. As there are several battery displays, you may find them on one out of five displays. Bob DM wrote: > > > Hello, all > > > > Been a long time since I have needed this list.... > > But it is always good to read what others are doing. > > > > My question is.... > > > > My favorite source of AA li energizer batteries no longer has them...;. > > > > Home depot at 4.19 a pair says they no longer stock them. > > > > Anyone else know of a reasonable source for these? > > > > I've seen them at Radio shack and other stores for around 10bucks a pair > (!) > > > > Thanks > > > > > > dave ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 10:43:20 -0600 Reply-To: "Batson, Dale N" Sender: HPLX Mailing List From: "Batson, Dale N" Subject: Re: Energizer Li battery... MIME-version: 1.0 Content-type: text/plain Content-transfer-encoding: 7BIT Sorry... I was thinking 4-pack! Here's a better source: http://www.smarthome.com/9820la.html Energizer Lithium AA Batteries (2 Pack) $5.49 -----Original Message----- I've never ordered from them, but Omega Man sells Energizer Lithium AA batteries @ $8.95 per two pak. http://www.omegamanenterprises.com/energizerlithiumaabatteries.htm -----Original Message----- From: Robert K. Meyer Ýmailto:bmeyer@UNION-TEL.COM¨ Sent: Sunday, August 19, 2001 11:31 PM To: HPLX-L@UCONNVM.UCONN.EDU Subject: Re: Fw: Energizer Li battery... Seems like I saw a pack of 4 at the Laramie Super Walmart for about 10 bucks. As there are several battery displays, you may find them on one out of five displays. Bob DM wrote: > > > Hello, all > > > > Been a long time since I have needed this list.... > > But it is always good to read what others are doing. > > > > My question is.... > > > > My favorite source of AA li energizer batteries no longer has them...;. > > > > Home depot at 4.19 a pair says they no longer stock them. > > > > Anyone else know of a reasonable source for these? > > > > I've seen them at Radio shack and other stores for around 10bucks a pair > (!) > > > > Thanks > > > > > > dave ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 22:52:31 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Mobile phone <--> HPLX home page updated MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends http://www.daniel-hertrich.de/mob_hplx changes: * new title * new section about faxing * more HSCSD init strings * thanks to Martin we now have a review for the new Ericsson T39m * new sction about phone book synchronization between phone and palmtop * new section about CDPD service which is available in the US, thanks to Bruce Maggs * AT command collections for HSCSD, GPRS and general AT commands (still looking for a collection for Ericsson phones!) GPRS is not yet usable. Andreas Garzotto works on correct GPRS connection handling by WWW/LX. On some other pages there are minor changes, for examplle on the serial port info page I now have more detailled info about the serial port of the 95LX. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 20:10:06 -0500 Reply-To: Chris Lott Sender: HPLX Mailing List From: Chris Lott Subject: Weird Case Break MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Today I was changing batteries in my HP200LX, and I noticed an unusual break in my case. There is a thin strip of plastic, part of the actual bottom of the case, along the side of the battery compartment. It you have the unit upside down, looking at battery compartment, it is the side of the compartment that runs along the outside edge of the case. Anyway, this thin piece of plastic cracked right in two! It doesn't appear at present that this weakens the case any, and is just a nuisance. I wonder if anyone else has encountered this before... -Chris -- ************************************************************************ R. Christopher Lott, P.E. rclott@ro.com Alpha Beta Technologies, Inc. 3112 12th Ave S.W. PHONE: 256-534-9067 Huntsville, Alabama 35805 FAX: 256-534-9069 ************************************************************************ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 22:38:17 -0500 Reply-To: Tim Sender: HPLX Mailing List From: Tim Subject: Can Any LX Program "snag" email addresses from headers (filter them from the junk)? In-Reply-To: <784F51866054D4118E8A00508BDF581A87D4B0@emss02m02.ems.lmco.com> MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hi all, this'll be a quick question. Got a typical "spam" (hoax) email.... One of the ones that say, "If you forward this to all your friends, $.07 will go to help some poor child with cancer..." Anyway, I took the time to go to one of the hoax sites, this one ÝUrban Legend Site http://www.snopes.com ¨ can let you search for the page/story that says, "This hoax has been around since xxxx and it has taken the following forms... Click HERE to forward this page to someone." Well, I spend about 20 min. in Notepad (yes, Windows ... sorry), ferreting out all the email addresses (had to sift through headers, etc. and remove angle brackets, "real" names and all sorts of work. Is there an LX program that can take one of these junk-ridden emails and give me a nice clean email list? TIA, --tim PS. I don't ALWAYS take time to do this; but, when I do, I'd like it to be faster! PPS. Three other good sites, for those who are interested, are: Urbanlegends. com http://www.urbanlegends.com CIAC Hoax list http://hoaxbusters.ciac.org/ and the Hoax Kill site http://www.hoaxkill.com/ ........ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 21 Aug 2001 11:09:55 +0200 Reply-To: Josef Meyer Sender: HPLX Mailing List From: Josef Meyer Subject: Manuals of Ericsson mobile phones MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Manuals of the Ericsson phones (also AT command set) can be found under http://www.ericsson.com/mobilityworld/ You have to register (sign up), free of charge. Then one can follow the link to the open zone: http://www.ericsson.com/mobilityworld/open/index.html and follow the links to the appropriate mobile phones (T39, R520, etc.). Josef Meyer ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 21 Aug 2001 16:02:39 +0200 Reply-To: furlan@gmx.net Sender: HPLX Mailing List From: "Dr. Werner Furlan" Organization: OE9FWV Subject: Re: Mobile phone <--> HPLX home page updated Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-type: text/plain; charset=US-ASCII Content-transfer-encoding: 7BIT hello Daniel, thank you for the information, especially the information about faxing with mobile phones and the palmtop. The cable connection to the phone seems to be crucial, do you know of any other working cable connections other than the Siemens phones? Werner on 20 Aug 2001, at 22:52 Daniel Hertrich wrote about: Mobile phone <--> HPLX home page updated > Hi friends > > http://www.daniel-hertrich.de/mob_hplx > > changes: > > * new title > * new section about faxing > * more HSCSD init strings > * thanks to Martin we now have a review for the new Ericsson T39m > * new sction about phone book synchronization between phone and palmtop * > new section about CDPD service which is available in the US, thanks to Bruce > Maggs * AT command collections for HSCSD, GPRS and general AT commands > (still looking for a collection for Ericsson phones!) > > GPRS is not yet usable. Andreas Garzotto works on correct GPRS connection > handling by WWW/LX. > > On some other pages there are minor changes, for examplle on the serial port > info page I now have more detailled info about the serial port of the 95LX. > > > GTX > daniel > > -- > http://www.daniel-hertrich.de/contact > -- PGP-Key: http://www.qsl.net/oe9fwv/furlan.asc SMS: +436646340014@text.mobilkom.at Powered by Pegasus Mail - free at www.pmail.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 21 Aug 2001 22:29:59 +0200 Reply-To: Josef Meyer Sender: HPLX Mailing List From: Josef Meyer Subject: WWW/Lx via GPRS MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Today I "borrowed" a GPRS/GSM Ericsson R520 mobile phone to play around with the phone and WWW/LX. With the settings in the phone I was able to access WAP pages through GPRS with the phone internal WAP browser. After this try with WAP I was sure that I found out the coreect settings for GPRS. This resulted in the following settings for WWW/LX: ÝGPRS_SC_Com¨ Port=1 OmniGo=0 PPP=1 Modem=1 Baud=38400 My_IP= DNS_IP=164.28.36.34 DNS2_IP=164.128.76.39 Script=CHAP_Script Login=gprs ModemInit=AT&F Dial=*99***5# Password= I connected the HPLX and the phone with a serial cable. When I tried to connect with WWW/LX to the provider, nothing at all happened! WWW/LX only showed 'Dialling *99***5#', then it hanged. With the inbuilt communication SW of the HPLX I managed the phone to dial with command 'ATD*99***5# (preceeded by At&F), which is the 'subscriber number' of the GPRS service. I got a 'connect' string as answer by dialling this way and the display of the phone said the same. Question: Is the string "99***5# not correctly sent out by WWW/LX? I have no other explanation. Why else is the phone estabishing a connection with comms, but not with WWW/LX? Any solutions? Josef Meyer ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 20 Aug 2001 23:37:33 +0100 Reply-To: fnsr@FREESURF.FR Sender: HPLX Mailing List From: Francois Ennesser Organization: NSR, Inc. Subject: PC Cards and Double Speed Problem Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: 8bit Hello all, I recently bought a 128 MB Compact Flash card from Kingston Technology with a Compact Flash to PC Card Adapter, with the intention of using it in my digital camera and in my 200LX as well. Unfortunately, I have a weird problem with this card. It works perfectly in my spare regular Single Speed 200Lx, but not in the double speed 64MB unit that I currently use ("Drive not ready. Abort, Retry, Ignore?" message). I also tested it in my old double speed 5MB unit, and it doesn't work there either. The tests were performed directly under DOS, both with and without the double speed drivers loaded. As I made the tests with 2 Kingston Conpact flash with the same result, I think we can conclude that Kingston Flash cards work in single speed LX, but not with double speed LX. The double speed upgrade documentation mentions Ethernet and Modem card that exhibit a similar behavior, but I didn't think that flash memory cards could have a problem too. So here are my questions: - Does anyone know of other memory cards that work in single speed units, but not with double speed? It would be great to put together a list of cards that do/do not work in single/double speed 200LX. (I made a proposal to build a similar list a couple of months ago, but did not come up with enough answers to do anything. BTW, thanks to those who responded!). - Does anyone know the possible interworking between the double speed crystal and the PCMCIA slot that could cause the problem? I suspect some protocol pulses become too short or arrive too fast too be recognized by some cards, but I would like to know exactly what happens. Thanks god, I still have an old 8MB Sandisk Compact flash that I can use to transfer images between my digital camera and double speed LX. But it would have been nice to know which cards would not work before buying one. So, Thanks in advance to anyone who sends me his experience of cards that do/do not work so that we can come up with a list to post on the web. Regards, F. Ennesser 19, rue des Feuillantines 75005 Paris Tel/Fax (33-1)4051-7580 f.ennesser@computer.org ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 21 Aug 2001 14:14:49 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Mind Map LX Comments: To: Fryday MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Fryday wrote: > Mind Map LX rocks! I'll certainly be registering and told another = friend about it. Thank you. > BTW, his vision is going, so he'd love a bigger font (doesn't > matter to him if he has to scroll around a bit more) Cannot use fonts other than the max that can be displayed. > Only one feature I would truly love to see in this program: > the ability to link to child. Do you mean an entry linking to another entry in another branch? I have not tried it, but I think you can already now link to another spot in the file itself, and so you can link to another entry. Something similar to So you can jump from one spot to another using the link, but not back. > Yep, would be tricky to show all > those links across the board, so here's how I would propose to > do it: give a tell-tale sign that there are links to other > children (similar to the idea of the "+" when there are > collapsed children), and only show the links to other children > when that one child is highlighted. When the children is not > highlighted, only show the tell-tale sign. If I understand it: you want to show the line between these two itms if, and only if, one of the two ends is highlighted. What if one end is off the screen? What if one end is hidden? How would you want to handle multiple links to one item? > Thanks for a great program! You are welcome. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 21 Aug 2001 15:34:29 -0700 Reply-To: Fryday Sender: HPLX Mailing List From: Fryday Subject: Re: Mind Map LX Comments: To: sponsor@ftel.net MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit > Cannot use fonts other than the max that can be displayed. If you ever come up with larger fonts, you'll probably expand your market as well :-) > > Only one feature I would truly love to see in this program: > > the ability to link to child. > Do you mean an entry linking to another entry in another > branch? I have not tried it, but I think you can already now > link to another spot in the file itself, and so you can link > to another entry. Something similar to HREF="thisfile.html#thisspot"> So you can jump from one spot > to another using the link, but not back. Actually, I'm looking for a visual cue, not an actual jump necessarily per se. > > Yep, would be tricky to show all > > those links across the board, so here's how I would propose to > > do it: give a tell-tale sign that there are links to other > > children (similar to the idea of the "+" when there are > > collapsed children), and only show the links to other children > > when that one child is highlighted. When the children is not > > highlighted, only show the tell-tale sign. > If I understand it: you want to show the line between these > two itms if, and only if, one of the two ends is highlighted. Actually, only one end. > What if one end is off the screen? Then you show it going off the end of the screen (just like the parent/child relationships you already have) > What if one end is hidden? Then connect to the parent. > How would you want to handle multiple links to one item? You show them all while the item is highlighted. Maybe put a limit of 5 links or something. > > Thanks for a great program! > You are welcome. Pleasure's all mine :-) A bientot, Philippe ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 21 Aug 2001 17:29:34 -0700 Reply-To: kopplin@TECHNOIR.NU Sender: HPLX Mailing List From: Mike Kopplin Subject: Re: Mind Map LX In-Reply-To: <030a01c12a95$58475c90$490c14ac@siebel.com> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Tue, 21 Aug 2001, Fryday wrote: > > Cannot use fonts other than the max that can be displayed. > > If you ever come up with larger fonts, you'll probably expand your market as > well :-) I don't recall the original question, but in mm.cfg you can have mm/lx use external fonts, rather than the built in ones, e.g. ÝFonts¨ 0=c:\fonts\huge.hfn 1=c:\fonts\large.hfn 2=c:\fonts\smaller.hfn etc. At least it worked when I tried it. Regards, Mike Kopplin ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 21 Aug 2001 17:29:34 -0700 Reply-To: kopplin@TECHNOIR.NU Sender: HPLX Mailing List From: Mike Kopplin Subject: Re: Mind Map LX In-Reply-To: <030a01c12a95$58475c90$490c14ac@siebel.com> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Tue, 21 Aug 2001, Fryday wrote: > > Cannot use fonts other than the max that can be displayed. > > If you ever come up with larger fonts, you'll probably expand your market as > well :-) I don't recall the original question, but in mm.cfg you can have mm/lx use external fonts, rather than the built in ones, e.g. ÝFonts¨ 0=c:\fonts\huge.hfn 1=c:\fonts\large.hfn 2=c:\fonts\smaller.hfn etc. At least it worked when I tried it. Regards, Mike Kopplin ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 04:57:55 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: WWW/Lx via GPRS MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Tue, 21 Aug 2001 22:29:59 +0200, Josef Meyer wrote: > Today I "borrowed" a GPRS/GSM Ericsson R520 mobile phone to play around > with the phone and WWW/LX. With the settings in the phone I was able to > access WAP pages through GPRS with the phone internal WAP browser. I can also do that with my Ericsson T39m > After this try with WAP I was sure that I found out the coreect > settings for GPRS. This resulted in the following settings for WWW/LX: > > ÝGPRS_SC_Com¨ > Port=1 > OmniGo=0 > PPP=1 > Modem=1 > Baud=38400 > My_IP= > DNS_IP=164.28.36.34 > DNS2_IP=164.128.76.39 > Script=CHAP_Script > Login=gprs > ModemInit=AT&F > Dial=*99***5# > Password= Here are my settings. I have only tried irda. But I can not get it connected. It stops on LCP negotiating. ÝISP_Gprs¨ ;mask1=0 ;nocompress=1 ;LCPwait=2 Port=-1 OmniGo=1 PPP=1 Modem=1 Baud=38400 My_IP=0.0.0.0 DNS_IP=212.17.131.3 DNS2_IP=212.17.113.194 Script=CHAP_Script Login=T39 ModemInit=AT+cgdcont=1,"IP","internet" ;Dial=*99*0*1*1# Password=>333 Dial=*99***1# You could try to have mask1=0 active and also nocompress=1 and LCPwait=2. Also try the other dialnumber which is rem'd above. Username and password should just be "something" I can not get this to work on irda. If you could try the above with cable I would appriciate it very much. Maybe I have to buy myself a cable. > I connected the HPLX and the phone with a serial cable. When I tried to > connect with WWW/LX to the provider, nothing at all happened! WWW/LX > only showed 'Dialling *99***5#', then it hanged. I get a bit further than that, because I have the correct AT string. > > With the inbuilt communication SW of the HPLX I managed the phone to > dial with command 'ATD*99***5# (preceeded by At&F), which is the > 'subscriber number' of the GPRS service. I got a 'connect' string as > answer by dialling this way and the display of the phone said the same. I get "connecting" but it stops while negotiating. > Question: Is the string "99***5# not correctly sent out by WWW/LX? I > have no other explanation. Why else is the phone estabishing a > connection with comms, but not with WWW/LX? > > Any solutions? I hope we can get some solution. Maybe irda is not possible, but cable is. Please try out the settings and let us know.. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 07:04:49 -0500 Reply-To: Jaime Viehweg Sender: HPLX Mailing List From: Jaime Viehweg Subject: FLUFFISH: hp200lx flies concord? Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii While watching something (60 minutes?) this past Sunday I noticed that the co-pilot was using an HP200LX to figure something while the voice over was describing the antiquated equipment that was available on the plane and that the flight crew had to do a lot of the work themselves. I don't know if it is standard issue or if that particular crew found that they needed the best "extra" equipment to get to their desired destinations. jaime -- jviehweg | Lucent Technologies - Bell Labs Innovations @ Jaime Viehweg | ATM Lab Support/Computing Environment lucent.com | IH Park 1Y-224 630-979-3813 http://www.atm.lucent.com -> "IH CSD Lab Policy" ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 06:49:40 -0600 Reply-To: Getz Sender: HPLX Mailing List From: Getz Subject: Flash Cards Comments: To: omnibook@elektro.cmhnet.org LEXAR MEDIA COMPACT FLASH CARD 16MB-$14.00 LEXAR MEDIA COMPACT FLASH CARD 32MB-$24.00 LEXAR MEDIA COMPACT FLASH CARD 48MB-$29.00 http://www.softwareandstuff.com/newarrival.html ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 15:58:14 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: PC Cards and Double Speed Problem MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Francois On Mon, 20 Aug 2001 23:37:33 +0100, Francois Ennesser wrote: > Unfortunately, I have a weird problem with this card. It works perfectly in > my spare regular Single Speed 200Lx, but not in the double speed 64MB > unit that I currently use ("Drive not ready. Abort, Retry, Ignore?" message). > I also tested it in my old double speed 5MB unit, When were the double speed upgrades of your palmtop have been made and by whom? What driver are you using? If they are older upgrades, or even not made by Thaddeus (Times2Tech), you may have either a so-called overtone Quartz crystal (is this the correct Englih word for "Oberwellen-Quarz"?), which may cause several problems, because 31.xxxx MHz, which is needed for the palmtop, is not the main frequency of that quartz, but an overtone, the over sine waves must be filtered out, so an additional electronics board is needed, or you even may have regular 32 MHz quartz, which is not the one the palmtop's processor actually wants. It is slightly faster than the optimal upgrade, so it may cause incompatibilities as well. You even need a special driver for these (cheap) kind of double speed upgrade. Some japanese people even have upgraded the palmtop to 36 MHz quatz speed (=18 MHz processor speed). I realy don't want to know how bad this works! :-( GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 15:58:15 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Mindmap/LX MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hello friends, hello Avi, I just downloaded the new version of MM/LX and I am amazed! Now all my previous problems are solved and I will now start to extensively use MM/LX (just waited for this release with my real MM/LX work). Today I began to create a mindmap which I want to structure a presentation with. Something like a "table of contents", from which I probably will directly create the presentation slides, and the notes shall contain the things I will speak about. Is there any way to _sort_ childs (i.e. if I have 10 childs with the names 1. theme 2. introduction 3. goal ... how can I assure that they appear in the correct order in the exported HTML file, or even in the .mm file itself)? Is this mainually be done by using the upwards / downward (¬U/¬D)? Can it be made automatically in any way? Thanks a lot daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 08:08:26 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: PC Cards and Double Speed Problem MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > On Mon, 20 Aug 2001 23:37:33 +0100, Francois Ennesser wrote: > > Unfortunately, I have a weird problem with this card. It works perfectly in > my spare regular Single Speed 200Lx, but not in the double speed 64MB > unit that I currently use ("Drive not ready. Abort, Retry, Ignore?" message). > I also tested it in my old double speed 5MB unit, I posted something of the same sort last October: << I bought a Canon A50 camera that came with a 8mb Canon branded CF card. The card did not work in my double-speed 200LX (with the same symptoms as you described), but worked fine in my unmodified single-speed 200LX. Further, several list members had the same card and swore that the card worked in their double-speed LXs, but to complicate things, it appeared also that the same Canon branded cards may have also have been manufactured by different vendors. My double-speed has never had a problem with a CF/flash card until this one, and I tried every suggestion (and then some) to make it work to no avail. I ultimately sold the card to another list member (with the appropriate warnings). >> - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 17:33:30 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: Mindmap/LX MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Daniel, > how can I assure that they appear in the correct order in the exported > HTML file, or even in the .mm file itself)? Do you have any example or indication that the order is been changed? Here they appear to be always the same as saved in the mm file > Is this mainually be done by using the upwards / downward (¬U/¬D)? > Can it be made automatically in any way? Do you really expect this feature from a mindmap program? Why don't you use a program like WordPerfect or Word which sorts your items automatically? Kind regards Helmuth ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 11:42:41 -0400 Reply-To: Bing Xu Sender: HPLX Mailing List From: Bing Xu Subject: TECH MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----=_NextPart_000_0083_01C12AFF.8D00C6F0" This is a multi-part message in MIME format. ------=_NextPart_000_0083_01C12AFF.8D00C6F0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Any info about 200lx's working with QCP2760 (QualComm 3-mode CDMA = cellphone)? And where to buy or download Webster or other English dictionaries for 200lx? Thanks a lot. Bing Canada ------=_NextPart_000_0083_01C12AFF.8D00C6F0 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable
Any info about 200lx's working with = QCP2760=20 (QualComm 3-mode CDMA cellphone)? And where to buy or download Webster = or other=20 English
dictionaries for 200lx? Thanks a=20 lot.

Bing
Canada

------=_NextPart_000_0083_01C12AFF.8D00C6F0-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 12:10:10 -0400 Reply-To: Christopher Blackmon Sender: HPLX Mailing List From: Christopher Blackmon Organization: Nortel Networks Subject: Re: TECH Comments: To: Bing Xu MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit I've used a 200lx with both a QCP860 and QCP2760 with Verizon's service. You just need the Qualcomm data cable to connect to the phone and the serial cable connected to the 200lx. I used WWW/LX to connect to a couple of different ISP's. Christopher. Bing Xu wrote: > Any info about 200lx's working with QCP2760 (QualComm 3-mode CDMA > cellphone)? And where to buy or download Webster or other English > dictionaries for 200lx? Thanks a lot. > > Bing > Canada > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 09:07:02 -0700 Reply-To: Fryday Sender: HPLX Mailing List From: Fryday Subject: Re: Mindmap/LX Comments: To: "Guenther Helmuth E." MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I'd say it would be neat to get MM/LX to sort based on some numbering of the items themselves, but otherwise I guess that yes, it probably will export in the order set by upward/downward, not that the positioning on the map should have anything to do with the actual 2D order. Thanks, Philippe ----- Original Message ----- From: "Guenther Helmuth E." To: Sent: Wednesday, August 22, 2001 8:33 AM Subject: Re: Mindmap/LX > Daniel, > > > how can I assure that they appear in the correct order in the exported > > HTML file, or even in the .mm file itself)? > > Do you have any example or indication that the order is been changed? > Here they appear to be always the same as saved in the mm file > > > Is this mainually be done by using the upwards / downward (¬U/¬D)? > > Can it be made automatically in any way? > > Do you really expect this feature from a mindmap program? > > Why don't you use a program like WordPerfect or Word which sorts your > items automatically? > > Kind regards > > Helmuth > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 11:17:56 -0500 Reply-To: melancon@microgear.net Sender: HPLX Mailing List From: Mike Melancon Subject: Re: TECH In-Reply-To: <008601c12b21$142579c0$7ee36481@acec15> MIME-Version: 1.0 Content-type: text/plain; charset=US-ASCII Content-transfer-encoding: 7BIT For dictionaries try: http://www.palmtoppaper.com/cgi-bin/shop.plx/SID=998496904.247/page=dictions.htm > Any info about 200lx's working with QCP2760 (QualComm 3-mode CDMA cellphone)? > And where to buy or download Webster or other English dictionaries for 200lx? > Thanks a lot. > > Bing > Canada > > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 00:20:51 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Source for DOS software collection MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Vivek, On Sun, 19 Aug 2001 00:07:32 +0530, Vivek Venugopalan wrote: > http://master.swlibero.org/~daniele/dos/valuedos.html Thanks for the link! This seems to be a great selection! GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 18:36:10 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: FLUFFISH: hp200lx flies concord? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > While watching something (60 minutes?) this past Sunday I noticed that > the co-pilot was using an HP200LX to figure something while the voice > over was describing the antiquated equipment that was available on the > plane Perhaps they ment that the 200LX IS the "antiquated equipment"? I mean, = the 200LX doesn't have color, or pretty icons, or a Windows operating system; = so it MUST be antiquated, right? Steve Carder (Typing away on his 200LX while the Jornada 680 sits = unused) ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 19:36:48 -0400 Reply-To: d Sender: HPLX Mailing List From: d Subject: Re: Mind Map LX Comments: To: kopplin@TECHNOIR.NU MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- > I don't recall the original question, but in mm.cfg you can have > mm/lx use external fonts, rather than the built in ones, e.g. > > ÝFonts¨ > 0=c:\fonts\huge.hfn > 1=c:\fonts\large.hfn > 2=c:\fonts\smaller.hfn Where do you get those fonts from? TIA Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 17:12:04 -0700 Reply-To: kopplin@TECHNOIR.NU Sender: HPLX Mailing List From: Mike Kopplin Subject: Re: Mind Map LX In-Reply-To: <001601c12b63$51464180$4aaafea9@computer> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Wed, 22 Aug 2001, d wrote: > ----- Original Message ----- > > I don't recall the original question, but in mm.cfg you can have > > mm/lx use external fonts, rather than the built in ones, e.g. > > > > ÝFonts¨ > > 0=c:\fonts\huge.hfn > > 1=c:\fonts\large.hfn > > 2=c:\fonts\smaller.hfn > > Where do you get those fonts from? Sorry, except for large.hfn, I was just making them up for an example. I don't recall where I got large.hfn from, but probably from one of the packages on SUPER like FontStuff, Pal Font Editor or one of the reader programs. After sending the last email I had second thoughts. It does work, but using external fonts also uses more memory which might cause a problem. So, I'm back to the internal fonts, but using large, middle and small. No tiny. Thats good enough for my eyes. Regards, Mike Kopplin ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 19:11:39 -0600 Reply-To: Richard and Patti Smith Sender: HPLX Mailing List From: Richard and Patti Smith Organization: Orion On-Site Computer Services Subject: ÝFwd: REX.net service ends August 31, 2001¨ MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit I think this is the beginning of the end of the Xircom Rex Micro-PDA line. I no longer see any benefit in the pursuit of any kind of interface between the Rex products and the 200LX. I've decided to just let it die, get used to it, and wait patiently for whatever might come along later that might fit my needs. Xircom (and the companies that developed it previously) was ahead of their time, just like HP with the 200LX. The 200LX is so capable that there is no replacement nor any real enhancement. "The 'Rex' is dead, long live the 'Rex.'"* Regards, Richard * Those who are familiar with the Latin meaning of the word "rex" will get the joke. rexteam@us.xircom.com wrote: > *** REX(R) MicroPDA Customer Alert *** > > Dear Valued Customer: > > Thank you for registering at REX.net. We hope you have enjoyed this free > service for your REX MicroPDA. We regret to inform you that the REX.net > website and service will be discontinued effective September 1, 2001. This > will not affect how you use your REX MicroPDA or how it works. > > We developed REX.net to closely tie an Internet-based service to the REX > 6000 Micro PDA. While we were optimistic that the REX.net user base would > be large enough to sustain the resources required to offer this service > and support future development, it has not grown as expected. > > If you synchronize with REX.net after August 31 but before December 31, > 2001, you will "clean out the contents" of your REX MicroPDA's Web > browser. This will free up memory for more contact records, memos, etc. > > We will continue to honor your existing REX product warranties and provide > you with technical support. > > If you have technical questions about your REX MicroPDA, please go to > www.Xircom.com for technical support or call (805) 376-9200. > > Again, thank you for registering at REX.net. We know you will continue to > enjoy your REX MicroPDA - the world's smallest, lightest, full-function > PDA. > > Yours truly, > Xircom, Inc., an Intel company > > P.S. For more information, please visit our REX.net FAQ page at > http://www.rex.net/rex/cda/faq/0,2110,203-13-0-3-0-1,00.html before August > 31, 2001. > > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > Please note: This communication is an important but non-recurring message > concerning your account. This is an outgoing message only. Please do not > "reply" to this e-mail. For technical questions please visit the Xircom > website. > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- Richard & Patti Smith Check out our virtual garage sale at http://seronac.freeservers.com/virtualgaragesale.html You're where you are because of who you are. But who you are is not as important as who you become. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 21:51:32 -0400 Reply-To: d Sender: HPLX Mailing List From: d Subject: Re: Mind Map LX Comments: To: kopplin@TECHNOIR.NU MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Mike Kopplin" > After sending the last email I had second thoughts. It does > work, but using external fonts also uses more memory which might > cause a problem. So, I'm back to the internal fonts, but using > large, middle and small. No tiny. Thats good enough for my eyes. The large font is the same as the smallest Sysmgr font, which doesn't make sense to me personally. That's why I was hoping. Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 19:56:01 -0700 Reply-To: Martin Crundall Sender: HPLX Mailing List From: Martin Crundall Subject: Re: FLUFFISH: hp200lx flies concord? Mime-Version: 1.0 Content-Type: text/plain; format=flowed Heh -- he was probably using LXGPS!! Jaime Viehweg said: While watching something (60 minutes?) this past Sunday I noticed that the co-pilot was using an HP200LX to figure something while the voice over was describing the antiquated equipment that was available on the plane and that the flight crew had to do a lot of the work themselves. I don't know if it is standard issue or if that particular crew found that they needed the best "extra" equipment to get to their desired destinations. _________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 22 Aug 2001 21:38:02 -0700 Reply-To: kopplin@TECHNOIR.NU Sender: HPLX Mailing List From: Mike Kopplin Subject: Re: Mind Map LX In-Reply-To: <000f01c12b76$2393ab20$4aaafea9@computer> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII > > After sending the last email I had second thoughts. It does > > work, but using external fonts also uses more memory which might > > cause a problem. So, I'm back to the internal fonts, but using > > large, middle and small. No tiny. Thats good enough for my eyes. > > The large font is the same as the smallest Sysmgr font, which doesn't make > sense to me personally. That's why I was hoping. I'm not sure what you mean. "large", "middle", "small" and "tiny" correspond to the 4 sysmgr fonts. So if you set all the levels to large, like 0=large 1=large 2=large etc. then MM/LX should display everything using the largest sysmgr font. Mike ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 09:02:58 +0200 Reply-To: Lasse Karlsson Sender: HPLX Mailing List From: Lasse Karlsson Subject: MM/LX forgets maps-dir MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Hi MM/LX-users, I have a problem with my setup of MM/LX (ver 1.1) I keep my maps in one directory and MM/LX in another and I use a batchfile like the one described on the T&T-page for startup. But as soon as i have invoked an external program like LXPIC or an editor MM/LX forgets the map-dir and uses the dir where MM/LX resides as map-dir. Is it a bug or might something be wrong with my setup? You can try for yourself with the example apps. As soon as I have displayed the Trentino map-map MM/LX cannot find the other maps anymore. Regards Lasse in Stockholm Sweden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 00:47:37 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Mindmap/LX Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Hi Daniel, I know Helmuth replied to yu, but I have a different perspective because I used MM/LX to do EXACTLY the things you talk about: One was a "map of maps", and there were two presentations I created. Daniel Hertrich wrote: > Is there any way to _sort_ childs (i.e. if I have 10 childs with the > names > 1. theme > 2. introduction > 3. goal You cannot sort their appearance on the screen, they will move about as you add and subtract material. But you can edit the source file and move items about using PE. That order will NOT change AFAIK. This is also the source that will be used by the HTML export, so the order of the HTML exported items will always be the same, even if on the screen their location changes positions a lot. The point about mindmapping is that you _want_ to discover new relationships, new perspectives on the information. When you see it all the time in the same order, your minds tends to accept what is and not look deeper into the material. When these items move around your mind will be released to not be "in a box", and discover new things, ideas, perspectives, aspects. My work on the presentation looked erratic - I kept going from item to item and adding here, there, changing stuff, and so on. But this was _within_ the main "chapters". So in the intro I had 4 main ideas and I kept changing the children of these 4 main ideas until I felt it was good. When I exported it, the for main ideas needed just one transposition, but all the creative material was there. Hope this helps. Avi ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 10:48:35 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Re: Mind Map LX Comments: To: kopplin@TECHNOIR.NU MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Mike Kopplin" > > The large font is the same as the smallest Sysmgr font, which doesn't make > > sense to me personally. That's why I was hoping. > I'm not sure what you mean. "large", "middle", "small" and > "tiny" correspond to the 4 sysmgr fonts. So if you set all the > levels to large, like Are you speaking of the first version, or of the new version (which I have not tried)? The first version had 3 fonts, the 2 smallest ones are way too small, the largest one being the default small Sysmgr font. When I zoom, the fonts get smaller, not bigger. Unless I missed something. Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 11:21:36 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Re: Mind Map LX Comments: To: kopplin@TECHNOIR.NU MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Mike Kopplin" > I'm not sure what you mean. "large", "middle", "small" and > "tiny" correspond to the 4 sysmgr fonts. So if you set all the > levels to large, like > > 0=large > 1=large > 2=large > etc. I just checked the cfg file, and this is what I found for fonts: 0=middle 1=middle 2=small 3=tiny 4=tiny I changed 2 to large, and now I see a bigger font, but the zoom command switches between tiny and large, nothing in between (before it was zooming between small & tiny, nothing else). Now that I figured that much out, what else am I missing with the zoom function? Looking at the help file, it appears zoom is intented to work that way. If so, is it any different in the new version? TIA Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 11:31:34 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Re: Mind Map LX Comments: To: kopplin@TECHNOIR.NU MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Mike Kopplin" > I'm not sure what you mean. "large", "middle", "small" and > "tiny" correspond to the 4 sysmgr fonts. So if you set all the > levels to large, like > 0=large > 1=large > 2=large > etc. > > then MM/LX should display everything using the largest sysmgr > font. I set everything to middle except 2, which I set to large. It still zooms between large and tiny, nothing else. That seems weird. Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 18:29:51 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: FLUFFISH: hp200lx flies concord? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Wed, 22 Aug 2001 18:36:10 -0400, Steve Carder wrote: > > While watching something (60 minutes?) this past Sunday I noticed that > > the co-pilot was using an HP200LX to figure something while the voice > > over was describing the antiquated equipment that was available on the > > plane > > Perhaps they ment that the 200LX IS the "antiquated equipment"? ..we ofcourse know that it is the plane they are talking about :-) > I mean, the > 200LX doesn't have color, or pretty icons, or a Windows operating system; so it > MUST be antiquated, right? That is what many people think yes. When I tell them what I have they laugh..but I know that I can do more than what they do.. Actually I seldom see people with pda's around here. My father has a Psion 5Mx and a friend of mine has a Series 5. Had one guy that came to work with a broken Series 5..then I saw maybe a couple of Palm's around. Some years ago at the university I was the only one(I think) with a pda. > Steve Carder (Typing away on his 200LX while the Jornada 680 sits unused) My brother has a 620 or maybe it was a 680lx. Can it be used to access websites that are secure. Https sites? That is maybe the only thing I would need it for when I travel. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 19:35:13 -0400 Reply-To: KenLondon Sender: HPLX Mailing List From: KenLondon Subject: Re: ÝFwd: REX.net service ends August 31, 2001¨ MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Richard and Patti Smith wrote: > I think this is the beginning of the end of the Xircom Rex Micro-PDA line Intel officially killed it today, ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 23 Aug 2001 20:00:40 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: ÝFwd: REX.net service ends August 31, 2001¨ MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Thu, 23 Aug 2001 19:35:13 -0400, KenLondon wrote: > Richard and Patti Smith wrote: > > > I think this is the beginning of the end of the Xircom Rex Micro-PDA line > > Intel officially killed it today, Saw something about a lawsuit against them somewhere.. People are not happy because they bought the Rex6000 based on what it could dowload from the rex.net. I am okey with two Rex3's. I will not sue anyone :-) Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 10:33:35 -0100 Reply-To: =?iso-8859-1?Q?Jos=E9?= Angel de Castro Barco Sender: HPLX Mailing List From: =?iso-8859-1?Q?Jos=E9?= Angel de Castro Barco Subject: Re: Flexa cards Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: base64 U29tZW9uZSBrbm93cyBpZiB0aGVzZSBjYXJkIHdvcmsgd2VsbCBpbiB0aGUgTFg/ClNvbWUgZHJp dmVyIHJlcXVlcmlkZWQ/CgoKCj5TZW5kZXI6ICAgICAgIEhQTFggTWFpbGluZyBMaXN0IDxIUExY LUxAVUNvbm5WTS5VQ29ubi5FZHU+Cj5Gcm9tOiAgICAgICAgIEdldHogPGpnZXR6QFdDRU5FVC5D T00+Cj5TdWJqZWN0OiAgICAgIEZsYXNoIENhcmRzCj5Db21tZW50czogVG86IG9tbmlib29rQGVs ZWt0cm8uY21obmV0Lm9yZwo+VG86ICAgICAgICAgICBIUExYLUxAVUNvbm5WTS5VQ29ubi5FZHUK Pgo+TEVYQVIgTUVESUEgQ09NUEFDVCBGTEFTSCBDQVJEIDE2TUItJDE0LjAwCj5MRVhBUiBNRURJ QSBDT01QQUNUIEZMQVNIIENBUkQgMzJNQi0kMjQuMDAKPkxFWEFSIE1FRElBIENPTVBBQ1QgRkxB U0ggQ0FSRCA0OE1CLSQyOS4wMAo+aHR0cDovL3d3dy5zb2Z0d2FyZWFuZHN0dWZmLmNvbS9uZXdh cnJpdmFsLmh0bWwKCioqIEhQTFgtTCBMSVNUIEluZm8gYXQgaHR0cDovL3d3dy5zcC51Y29ubi5l ZHUvfm1jaGVtMS9IUExYLnNodG1sCgoKCioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioq KioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKgpKb3PpIEFuZ2VsIGRlIENhc3RybyAg ICAgICAgICAgICAgICAgICAgICBUbm86IDM0IDk4MyAzMyA3MiA5OQpDL1MuTG9yZW56bywxLTO6 Qgo0NzAwMSBWQUxMQURPTElEIChTUEFJTikgICAgICAgICAgICAgICAgICBjYXN0cm9iYXJjb0B3 b2wuZXMKKioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioqKioq KioqKioqKioqKioqKioqCgo= ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 06:30:58 -0600 Reply-To: David Feldman Sender: HPLX Mailing List From: David Feldman Subject: Re: Flexa cards Comments: To: =?iso-8859-1?Q?Jos=E9_Angel_de_Castro_Barco?= MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 8bit The LEXAR cards FAIL in a HP OMNIBOOK 300/425; I doubt they'd work in the LX machines for the same reason (they depend on a proprietary windows 9x series driver.) ----- Original Message ----- From: Josi Angel de Castro Barco To: Sent: Friday, August 24, 2001 5:33 AM Subject: Re: Flexa cards > Someone knows if these card work well in the LX? > Some driver requerided? > > > > >Sender: HPLX Mailing List > >From: Getz > >Subject: Flash Cards > >Comments: To: omnibook@elektro.cmhnet.org > >To: HPLX-L@UConnVM.UConn.Edu > > > >LEXAR MEDIA COMPACT FLASH CARD 16MB-$14.00 > >LEXAR MEDIA COMPACT FLASH CARD 32MB-$24.00 > >LEXAR MEDIA COMPACT FLASH CARD 48MB-$29.00 > >http://www.softwareandstuff.com/newarrival.html > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > > > > ****************************************************************** > Josi Angel de Castro Tno: 34 983 33 72 99 > C/S.Lorenzo,1-3:B > 47001 VALLADOLID (SPAIN) castrobarco@wol.es > ****************************************************************** > > r,2L?!+6Z 2>"yvor Wq-{ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 09:06:09 -0400 Reply-To: ashoni arora Sender: HPLX Mailing List From: ashoni arora Subject: 200LX 8MB <-> j720 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit MIME-Version: 1.0 I have a 200LX 8MB DS with adapter software carousel book- PC in your pocket Intellisync Connectivity Pack Project Kick start All related documentation & cables All in excellent condition Is anyone on the list interested in swapping it for a jornada 720 (I already have a 690) -- ashoni arora ashoni@onebox.com - email (212) 894-3702 x4073 - voicemail/fax __________________________________________________ FREE voicemail, email, and fax...all in one place. Sign Up Now! http://www.onebox.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 09:30:54 -0400 Reply-To: KenLondon Sender: HPLX Mailing List From: KenLondon Subject: Re: ÝFwd: REX.net service ends August 31, 2001¨ MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Martin Bergvill wrote: > Saw something about a lawsuit against them somewhere.. People are not > happy because they bought the Rex6000 based on what it could dowload > from the rex.net. How can they sue? They bought a rex based on promises from a company that no longer exists. The whole shooting match is now owned by Intel and they have the option of doing what they want. I would guess that somewhere in the fine print for the Rex is the option for any services to be shut down when the owner decides to. More than likely the Intel lawyers found they had no legal obligation to keep rex.net up and running. Also I have a rex and saw nothing about rex.net in the material included with the device. Where did you learn about this rex.net? ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 10:50:39 +0200 Reply-To: Alan Krempler Sender: HPLX Mailing List From: Alan Krempler Subject: QuickView and MiniDict: Where to download MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit as expected, s.u.p.e.r. updates take some time these days. Qman has been so kind to lend me a corner of his website to make the programs available. http://home.earthlink.net/~qman/ his page is being redesigned. so you will have to look around. at the moment, the "downloads" link will take you to the programs. new versions are being worked on and will be available by autumn alan ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 09:23:23 -0500 Reply-To: Bryan Biggers Sender: HPLX Mailing List From: Bryan Biggers Subject: Re: Flexa cards MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Wait a second, the lexar cards work OK in the LX, at least the three that I have do. They don't use a special driver under Windows 9x. The issue with the Omnibook must be something else. Bryan David Feldman wrote: > > The LEXAR cards FAIL in a HP OMNIBOOK 300/425; I doubt > they'd work in the LX machines for the same reason (they depend on > a proprietary windows 9x series driver.) > > ----- Original Message ----- > From: Josi Angel de Castro Barco > To: > Sent: Friday, August 24, 2001 5:33 AM > Subject: Re: Flexa cards > > > Someone knows if these card work well in the LX? > > Some driver requerided? > > > > > > > > >Sender: HPLX Mailing List > > >From: Getz > > >Subject: Flash Cards > > >Comments: To: omnibook@elektro.cmhnet.org > > >To: HPLX-L@UConnVM.UConn.Edu > > > > > >LEXAR MEDIA COMPACT FLASH CARD 16MB-$14.00 > > >LEXAR MEDIA COMPACT FLASH CARD 32MB-$24.00 > > >LEXAR MEDIA COMPACT FLASH CARD 48MB-$29.00 > > >http://www.softwareandstuff.com/newarrival.html > > > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > > > > > > > > ****************************************************************** > > Josi Angel de Castro Tno: 34 983 33 72 99 > > C/S.Lorenzo,1-3:B > > 47001 VALLADOLID (SPAIN) castrobarco@wol.es > > ****************************************************************** > > > > r,2L?!+6Z 2>"yvor Wq-{ > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 10:30:32 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Re: Flexa cards Comments: To: omnibook@elektro.cmhnet.org In-Reply-To: <3B86635B.B1E17CFF@charter.net> MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit It's a problem with the OB300. The 300 has a non-standard PCMCIA slit. Sandisk cards work well in 'em but a smart modular card I had would not work. The card did work in the 200lx. I think that Sandisk supports an ATA standard that makes the card look more like a real IDE hard drive. They just put a whole lot more in their cards which is what makes them the best. > -----Original Message----- > From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu¨On > Behalf Of > Bryan Biggers > Sent: Friday, August 24, 2001 10:23 AM > To: HPLX-L@uconnvm.uconn.edu > Subject: Re: Flexa cards > > > Wait a second, the lexar cards work OK in the LX, at least the > three that I have do. They don't use a special driver under > Windows 9x. The issue with the Omnibook must be something else. > Bryan > > > David Feldman wrote: > > > > The LEXAR cards FAIL in a HP OMNIBOOK 300/425; I doubt > > they'd work in the LX machines for the same reason (they depend on > > a proprietary windows 9x series driver.) > > > > ----- Original Message ----- > > From: Josi Angel de Castro Barco > > To: > > Sent: Friday, August 24, 2001 5:33 AM > > Subject: Re: Flexa cards > > > > > Someone knows if these card work well in the LX? > > > Some driver requerided? > > > > > > > > > > > > >Sender: HPLX Mailing List > > > >From: Getz > > > >Subject: Flash Cards > > > >Comments: To: omnibook@elektro.cmhnet.org > > > >To: HPLX-L@UConnVM.UConn.Edu > > > > > > > >LEXAR MEDIA COMPACT FLASH CARD 16MB-$14.00 > > > >LEXAR MEDIA COMPACT FLASH CARD 32MB-$24.00 > > > >LEXAR MEDIA COMPACT FLASH CARD 48MB-$29.00 > > > >http://www.softwareandstuff.com/newarrival.html > > > > > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > > > > > > > > ****************************************************************** > > Josi Angel de Castro Tno: 34 983 33 72 99 > > C/S.Lorenzo,1-3:B > > 47001 VALLADOLID (SPAIN) castrobarco@wol.es > > ****************************************************************** > > > > r,2L?!+6Z 2>"yvor Wq-{ > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 12:09:17 -0400 Reply-To: victor_roberts@COMPUSERVE.COM Sender: HPLX Mailing List From: Victor Roberts Subject: Re: What to do with a big flashcard? Comments: To: Mike Cheponis MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Tue, 5 Jun 2001 19:04:12 -0700 (PDT), Mike Cheponis wrote: > > I don't think there would be much disagreement that the appt book and the > other db s/w is buggy; so is Quicken, for that matter. > > If you haven't seen these bugs, then perhaps you believe that -you- did > something wrong, and therefore, you assume that the machine is "ok" and you > are "incorrect", or maybe you just don't push the apps like I do. Well, I don't know what you do with your appointment book and other apps. I use mine many times each day. I use ToDos and keep notes in my appointments and also use alarms on a regular basis. How else would you like me to "push" them? What may be different is that I do not use SC. Is there any correlation between those people who have problems with the built-in apps and those who use SC? If so, I don't see how you can blame this on HP. Vic Roberts ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 09:23:01 -0700 Reply-To: Mike Cheponis Sender: HPLX Mailing List From: Mike Cheponis Subject: Re: What to do with a big flashcard? Comments: To: Victor Roberts In-Reply-To: <200108241609.MAA02188@siaar1aa.compuserve.com> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Are you saying that you have NEVER seen ANY bugs in the HP s/w? -Mike On Fri, 24 Aug 2001, Victor Roberts wrote: > From: Victor Roberts > On Tue, 5 Jun 2001 19:04:12 -0700 (PDT), Mike Cheponis wrote: >> I don't think there would be much disagreement that the appt book and the >> other db s/w is buggy; so is Quicken, for that matter. >> If you haven't seen these bugs, then perhaps you believe that -you- did >> something wrong, and therefore, you assume that the machine is "ok" and you >> are "incorrect", or maybe you just don't push the apps like I do. >Well, I don't know what you do with your appointment book and >other apps. I use mine many times each day. I use ToDos and >keep notes in my appointments and also use alarms on a regular >basis. How else would you like me to "push" them? > >What may be different is that I do not use SC. Is there any >correlation between those people who have problems with the >built-in apps and those who use SC? If so, I don't see how you >can blame this on HP. > > Vic Roberts ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 12:52:32 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Re: What to do with a big flashcard? In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit There are definitely some corruption problems when you let the appointment book data file get too big. I'm not sure about the phone book tho. > -----Original Message----- > From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu¨On > Behalf Of > Mike Cheponis > Sent: Friday, August 24, 2001 12:23 PM > To: HPLX-L@uconnvm.uconn.edu > Subject: Re: What to do with a big flashcard? > > > Are you saying that you have NEVER seen ANY bugs in the HP s/w? > > -Mike > > > On Fri, 24 Aug 2001, Victor Roberts wrote: > > > From: Victor Roberts > > > On Tue, 5 Jun 2001 19:04:12 -0700 (PDT), Mike Cheponis > wrote: > > >> I don't think there would be much disagreement that the > appt book and the > >> other db s/w is buggy; so is Quicken, for that matter. > > >> If you haven't seen these bugs, then perhaps you believe > that -you- did > >> something wrong, and therefore, you assume that the > machine is "ok" and you > >> are "incorrect", or maybe you just don't push the apps like I do. > > >Well, I don't know what you do with your appointment book and > >other apps. I use mine many times each day. I use ToDos and > >keep notes in my appointments and also use alarms on a regular > >basis. How else would you like me to "push" them? > > > >What may be different is that I do not use SC. Is there any > >correlation between those people who have problems with the > >built-in apps and those who use SC? If so, I don't see how you > >can blame this on HP. > > > > Vic Roberts > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 11:07:18 -0700 Reply-To: kopplin@TECHNOIR.NU Sender: HPLX Mailing List From: Mike Kopplin Subject: Re: Mind Map LX In-Reply-To: <005801c12be7$4da84e40$bc6a6c40@computer> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII > > I'm not sure what you mean. "large", "middle", "small" and > > "tiny" correspond to the 4 sysmgr fonts. So if you set all the > > levels to large, like > > > > I just checked the cfg file, and this is what I found for fonts: > 0=middle > 1=middle > 2=small > 3=tiny > 4=tiny > > I changed 2 to large, and now I see a bigger font, but the zoom command > switches between tiny and large, nothing in between (before it was zooming > between small & tiny, nothing else). > Now that I figured that much out, what else am I missing with the zoom > function? Looking at the help file, it appears zoom is intented to work > that way. If so, is it any different in the new version? I'm using the new version, and I believe it was the same in the first one. I think that is the way the zoom is intended to work. Maybe think of it more as a ZOOM OUT function, using the small font to show as much of the map on the screen as possible, instead of rotating between different font sizes like in PE or the built-in apps. The fonts set in the cfg file are what you get unzoomed. Mike ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 14:22:15 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Re: Mind Map LX Comments: To: kopplin@TECHNOIR.NU MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Mike Kopplin" > The fonts set in the cfg file > are what you get unzoomed. I wonder why there are 5 font settings when you can only use two at a time . . . Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 20:27:10 +0100 Reply-To: HP Staber Sender: HPLX Mailing List From: HP Staber Subject: Re: 200LX 8MB <-> j720 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable ashoni arora > I have a 200LX 8MB DS with > adapter > software carousel > book- PC in your pocket > Intellisync > Connectivity Pack > Project Kick start > All related documentation & cables > > All in excellent condition > > Is anyone on the list interested in swapping it for a jornada 720 (I > already have a 690) I have both and would not want to swap a 200LX for a J720 ;-) HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 11:40:57 -0700 Reply-To: kopplin@TECHNOIR.NU Sender: HPLX Mailing List From: Mike Kopplin Subject: Re: Mind Map LX In-Reply-To: <002201c12cc9$b49e33c0$4aaafea9@mama> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII > > The fonts set in the cfg file > > are what you get unzoomed. > > I wonder why there are 5 font settings when you can only use two at a time I think I see the confusion now. You are using all 5 font settings when in unzoomed mode. When you have 0=large in the cfg file, it means items at level 0 (the parent) uses the large font. 1=middle would mean items at level 1 (the first children) use the middle fontsize. Similarly, you specifiy the font size at different levels (or layers of children). This way you can have the important items or overall ideas at the top levels in a larger font, and the less important grandchildren and greatgrandchildren (details) in smaller fonts. If you don't see different font sizes displayed when not ZOOMed, then something isn't working right. Mike ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 11:45:44 -0700 Reply-To: wayne.yang@bigfoot.com Sender: HPLX Mailing List From: "Wayne E. Yang" Subject: Fluffish - HP200LX=>Concord MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="0-149720042-998678744=:74568" --0-149720042-998678744=:74568 Content-Type: text/plain; charset=us-ascii Speaking of interesting uses of HP200LXes... Anyone else see the recent National Geographic episode where a team made a 380-day trek across the rainforests of Gabon? The lead geographer seemed to have an HP200LX too. Too bad Thaddeus doesn't print HP Palmtop anymore. I would be curious to know how they used it. http://www.wayneyang.com --------------------------------- Do You Yahoo!? Make international calls for as low as $0.04/minute with Yahoo! Messenger. --0-149720042-998678744=:74568 Content-Type: text/html; charset=us-ascii

Speaking of interesting uses of HP200LXes...

Anyone else see the recent National Geographic episode where a team
made a 380-day trek across the rainforests of Gabon? The lead geographer
seemed to have an HP200LX too. Too bad Thaddeus doesn't print HP
Palmtop anymore. I would be curious to know how they used it.

http://www.wayneyang.com


Do You Yahoo!?
Make international calls for as low as $0.04/minute with Yahoo! Messenger. --0-149720042-998678744=:74568-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 01:07:49 +0200 Reply-To: Frank LOUWERS Sender: HPLX Mailing List From: Frank LOUWERS Subject: Re: What to do with a big flashcard? Comments: To: "victor_roberts@COMPUSERVE.COM" MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit On Fri, 24 Aug 2001 12:09:17 -0400, Victor Roberts wrote: >Well, I don't know what you do with your appointment book and >other apps. I use mine many times each day. I use ToDos and >keep notes in my appointments and also use alarms on a regular >basis. How else would you like me to "push" them? > >What may be different is that I do not use SC. Is there any >correlation between those people who have problems with the >built-in apps and those who use SC? If so, I don't see how you >can blame this on HP. > Hi All, Well I use Appointments (with to do's, alarms etc), Database, Lotus 123, HP Calc, Memo, World Time, System Macro's and (occasionally) Pocket Quicken extensiveley together with several other programs in 9 other sessions under Software Caroussel (v6.89) all open at the same time and switching continually between them. I do this since several years and I wouldn't really know that the software is buggy. I never am stuck in the apps. What I do have occasionally is a failure in my automatic backup macro launched from Appointments every morning, and I have not been able to reproduce the exact circumstances when it will fail. The only other thing is that (even without SC running) in one or two built-in apps in the menu there is no response to my typing Q (for quit), I have to use the arrows to get there. Can't remember in which ones, I gues they are happy running and don't want to quit Best regards, ...Frank LOUWERS (Belgium)... ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 17:13:03 -0700 Reply-To: patrick@west.net Sender: HPLX Mailing List From: Patrick West Subject: MobiPocket reader In-Reply-To: <20010824153653.19326.qmail@web10708.mail.yahoo.com> Mime-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Folks, Does anyone know of any tools for reading texts formated for use= with MobiPocket reader on the HPLX? MobiPocket reader can be found at www.mobipocket.com -- Patrick West, francis_patrick_west@yahoo.com on 08/24/2001 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 17:47:03 -0700 Reply-To: patrick@west.net Sender: HPLX Mailing List From: Patrick West Subject: A slow lighter system Mime-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Folks, My doublespeed 5meg 200lx has a dying screen. The right half= starts bluring and shifting and even showing stuff from the left= half. If I give it a slight wack to the back of the lid it will= work normally for a few minutes. My backup machine is a 1 meg 100lx. =A0I have been switching stuff= and keep running in to with the way I'm used to doing things. I tend to run everything from appmanager. DOS stuff I run using= MaxDOS. However MaxDOS doesn't run well on the 100lx as I have one the 1= meg and MaxDOS wants a nice large bit of disk space to swap apps= in and out. =A0 So I find my self using HDM in DOS but then the appointment book= is closed and doesn't beep. =A0So any ideas? =A0Is there something I= can use on a 100lx like MaxDOS? =A0 Or tips on getting maxDOS to work? =A0 -- Patrick West, patrick@west.net on 08/24/2001 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 24 Aug 2001 20:22:34 -0500 Reply-To: Dan Ridenhour Sender: HPLX Mailing List From: Dan Ridenhour Subject: HP 200lx/1000cx Battery Test Results - Proving what we already know! MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit All, Well, its official im a confirmed gadget nut and have been for some time since I first set eyes on a Radio Shack PC-2 pocket computer... but I degress. I started a site a while back to post battery times between various handhelds that fed my handheld addiction... It lists tests of Palms, Pocket PCs, etc. and the most recent test is of a HP 1000cx with standard duracell AA batteries. This test proves what we all have been saying for years... nothing beats the HP 200lx battery life. Checkout my site at http://gizmo.digital-alchemy.net if you want to see how our beloved handheld stacks up to the competition. Dan Ridenhour driden@stlnet.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 05:36:10 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: new "areacode.gdb" for SUPER MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I just finished AREACODE.GDB, listing 282 telephone area codes for North America (USA/Canda) because the WDB list is inconvenient and incomplete for finding locations via area codes. First column are the numbers 201 New Jersey to 978 Massachusetts. Second column are the locations (States), and third column are their abbreviations, ie. NJ or MA. There are no notes in order to make search/find near instantaneous. Subsets show states with all area codes; ie. California tops the list with 35, followed by Texas with 18. Since the SUPER site is temporarily down, you may ask me for a copy. It is 12970 (5348 zipped) after import to a new file to eliminate 'garbage' (i haven't figured out how to cut garbage any other way, or why it increases all the time even without editing) You are welcome to add any codes i may have left out. Nathalie ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 11:04:59 +0000 Reply-To: Stefan.Peichl@T-ONLINE.DE Sender: HPLX Mailing List From: Stefan Peichl Subject: Re: A slow lighter system MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Patrick West wrote: > My doublespeed 5meg 200lx has a dying screen... > My backup machine is a 1 meg 100lx. Why don't you put your 200lx mainboard into your 100lx? I did it already years ago, because I prefer the black color of the 100lx case. If you know how to open the palmtop case, it is a 5 minutes operation. Stefan ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 11:59:55 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Flexa cards MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, On Fri, 24 Aug 2001 10:30:32 -0400, Ed Padin wrote: > It's a problem with the OB300. The 300 has a non-standard PCMCIA slit. > Sandisk cards work well in 'em but a smart modular card I had would > not work. The card did work in the 200lx. I think that Sandisk The early Omnibooks (300 - 600) have two totally different kinds of PCMCIA slots: On the left side there are slots just like the one of the 200LX, a full-featured PCMCIA slot (double, on the Omnibooks, the 200LX has jsut one), maybe a few limitations compared to newer standards, regarding compatibility to modern cards. On the right side, the Omnibooks have a Type3 PCMCIA slot, which is not a full-featured PCMCIA slot, but which is actually a standard IDE port, with PCMCIA pin mapping. So you can put IDE hard disks in there with PCMCIA connector, Flash cards or Microdrives SHOULD also work, if they follow the IDE standard. No other kind of PCMCIA card work in these slots. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 11:59:56 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: What to do with a big flashcard? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Frank, On Sat, 25 Aug 2001 01:07:49 +0200, Frank LOUWERS wrote: > reproduce the exact circumstances when it will fail. The only other thing is that (even without SC > running) in one or two built-in apps in the menu there is no response to my typing Q (for quit), I > have to use the arrows to get there. Can't remember in which ones, I gues they are happy running and > don't want to quit :-) I get exactly this behaviour (not always, but often) after switching back from another work area to WA1 (system manager). If I then press Menu-E (Ende = Quit), the menu apears, sometimes in a garbled font, if I come from a work area which uses all built-in fonts, such as Post/LX, but the menu doesn't react on any of the shortcuts. I have to use the arrow keys and then press enter. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 11:59:57 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: A slow lighter system MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Patrick., On Fri, 24 Aug 2001 17:47:03 -0700, Patrick West wrote: > My doublespeed 5meg 200lx has a dying screen. The right half starts bluring and shifting and even showing stuff from the left > half. If I give it a slight wack to the back of the lid it will work normally for a few minutes. > > My backup machine is a 1 meg 100lx. -I have been switching stuff and keep running in to with the way I'm used to doing things. You can swa the screens. The screens are identical on both the 100LX and 200LX. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 11:59:58 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: new "areacode.gdb" for SUPER MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Nathalie On Sat, 25 Aug 2001 05:36:10 +0200, Nathalie Bugeaud wrote: > I just finished AREACODE.GDB, listing 282 telephone area codes for North Oh yes, please send me a copy. :-) > 12970 (5348 zipped) after import to a new file to eliminate 'garbage' (i > haven't figured out how to cut garbage any other way, or why it increases > all the time even without editing) Do you use this "fastdb" TSR (or whatever its name is)? I think this could cause such problems, because, AFAIK, changes in the GDB are not really worked into the GDB, but appended, for faster processing, just like the "fast save" option of MS Word works. I can be wrong, since I have never used it. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 14:42:22 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: Mind Map LX MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Domingo, > ----- Original Message ----- > From: "Mike Kopplin" > > The fonts set in the cfg file > > are what you get unzoomed. > > I wonder why there are 5 font settings when you can only use two at a time > . . . I had a quick look at help.mm HELP.MM: --- ZOOM: Toggle tiny font ÝFonts¨ section 0=...4=: fonts for levels 0=Large tells MM/LX to use the large font for level 0 (central) items. 1=Middle tells MM/LX to use the middle font for level 0 (main branch). etc. --- If you have any further question don't hesitate to ask. Kind regards Helmuth ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 09:13:42 -0500 Reply-To: Scott Barrett Sender: HPLX Mailing List From: Scott Barrett Subject: palm connectivity MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit I looked through the list archives and could not find anything like this, but I thought I would ask... Is there a utility that would let an HP200 send and recieve the beam signals that the palms use? I guess I am looking at a way to transmit and recieve the phone book and appointment book items. I have not programmed these units, but it seems like it could be a TSR triggered by a keystroke, maybe if you want to send, just highlight the appt or phone book person and hit ctrl-S, recieve could work similar. I could see am issue with data translation, but from looking at friends palms, many fields are very similar and just need to be pointed in the right direction. Does this exist or is this a new idea. It sure would bring 200 users into a broader capability. Scott ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 07:57:52 -0700 Reply-To: patrick@west.net Sender: HPLX Mailing List From: Patrick West Subject: Re: A slow lighter system Mime-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable I tend to be all thumbs. My 100lx is one assembled from two= broken machines and I almost couldn't get it to work. I don't see how to disconnect the screen ribbon cable from the= board and swap boards. On Sat, 25 Aug 2001 11:04:59 +0000, Stefan Peichl wrote: >Patrick West wrote: > >>=A0My doublespeed 5meg 200lx has a dying screen... >>=A0My backup machine is a 1 meg 100lx. > >Why don't you put your 200lx mainboard into your 100lx? >I did it already years ago, because I prefer the black color of= the >100lx case. > >If you know how to open the palmtop case, it is a 5 minutes >operation. > >Stefan > >** HPLX-L LIST Info at= http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- Patrick West, francis_patrick_west@yahoo.com on 08/25/2001 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 11:51:45 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Flexa cards MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable David Feldman wrote: > The LEXAR cards FAIL in a HP OMNIBOOK 300/425; I doubt > they'd work in the LX machines for the same reason (they depend on > a proprietary windows 9x series driver.) Bad conclusion. I use lexar cards successfully in LX and in Windows of several ilks. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 11:51:40 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: MM/LX 1.1a Uploaded to D&A Site MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Folks, FYI: MM/LX version 1.1a uploaded to D&A Website last night. This version has just one small bug fix. In case you are unaware, we also uploaded on the 16th of August MM/LX 1.1 a major improvement. It had a small bug which was repaired. If you want to see the details, head to http://www.dasoft.com/MMLX/mmupd.htm ... The latest released version is on top, and prior releases are behind it, down the page. Enjoy! Avi Meshar D&A Software http://www.dasoft.com PS: I am interested to know your about impressions you have using PayPal. I am considering using it for D&A sales, allowing customers to purchase software, SECURELY, right from the Website. Please let me know in private email. Thank you. PPS: We migrated out mailing list to Topica.com. So far, no problems. I would like to encourage you to join. This is for announcements only, and I usually throw in some tip of usage or two also... The volume of messages is VERY small, I too hate junk mail/email and spams ... To join, send email to da.info-subscribe@topica.com. When you get the confirmation email (they want to verify you really want to join), you can just reply by email, or use their "One Click" reply to join Topica.com and take advantage of their other services, and be able to read posted message on the Web. You DO NOT HAVE to join Topica.com to receive our emails. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 11:51:48 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: MM/LX forgets maps-dir Comments: To: Lasse Karlsson MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable I think this was just fixed in MM/LX 1.1a uploaded last night (Friday, 24 Aug) Mind trying it and give feedback again? Check out http://www.dasoft.com/MMLX/mmupd.htm (there is description and direct links to d/l the program...) Thanks in advance? Avi Lasse Karlsson wrote: > Hi MM/LX-users, > I have a problem with my setup of MM/LX (ver 1.1) > I keep my maps in one directory and MM/LX in another > and I use a batchfile like the one described on the T&T-page > for startup. > But as soon as i have invoked an external program like LXPIC or > an editor MM/LX forgets the map-dir and uses the dir where MM/LX > resides as map-dir. > Is it a bug or might something be wrong with my setup? > You can try for yourself with the example apps. > As soon as I have displayed the Trentino map-map > MM/LX cannot find the other maps anymore. > > Regards > Lasse in Stockholm Sweden > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 15:33:10 -0500 Reply-To: Tim Sender: HPLX Mailing List From: Tim Subject: LX <--> Palm via IR In-Reply-To: <20010825145753.VBSQ19181.femail35.sdc1.sfba.home.com@dell-one> MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hi all, Anyone having any luck beaming documents, files, etc. between a PalmOS device and a 200LX (or any LX for that matter)? I tried some of the "Super" downloads, some time ago.... One had some command/features like "oput" and "oget" I think, but didn't have any luck. Any help would be appreciated.... --tim Also, if I can beam, can I CONVERT say, a .WK1 spreadsheet into something the Palm can use (or vice-versa)? ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 13:41:44 -0700 Reply-To: Martin Crundall Sender: HPLX Mailing List From: Martin Crundall Subject: Re: HP 200lx/1000cx Battery Test Results - Proving what we already know! Mime-Version: 1.0 Content-Type: text/plain; format=flowed tks dan. can you combine the tests somehow? the minutes column seems to be redundant, so you'd get some extra space there. ----Original Message Follows---- From: Dan Ridenhour Reply-To: Dan Ridenhour To: HPLX-L@UConnVM.UConn.Edu Subject: HP 200lx/1000cx Battery Test Results - Proving what we already know! Date: Fri, 24 Aug 2001 20:22:34 -0500 All, Well, its official im a confirmed gadget nut and have been for some time since I first set eyes on a Radio Shack PC-2 pocket computer... but I degress. I started a site a while back to post battery times between various handhelds that fed my handheld addiction... It lists tests of Palms, Pocket PCs, etc. and the most recent test is of a HP 1000cx with standard duracell AA batteries. This test proves what we all have been saying for years... nothing beats the HP 200lx battery life. Checkout my site at http://gizmo.digital-alchemy.net if you want to see how our beloved handheld stacks up to the competition. Dan Ridenhour driden@stlnet.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml _________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 22:59:43 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: URGENT: palm pdb database -> text or gdb MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, I'll visit the IFA (internationale Funk-Ausstellung = international broadcast exhibition, showing the new trends in entertainment electronics and so on) here in Berlin tomorrow. Today I have looked for a list of exhibitors in text format to load it onto my LX. Unfortunately, these idiots only have published somthing special for the palm and for WinCE devices. I found a file with PDB as extension and it indeed contains the data I need (the text is in there, but embedded into some weird binary stuff and very bad formatted). Does anyone know of a way to convert this into plain text or maybe even into GDB format? The file can be found in the zip archive http://ifa-berlin.de/palmppc/vers1/palm/ifa2001_de.zip or in English at http://ifa-berlin.com/palmppc/vers2/palm/ifa2001_en.zip I need the solution within the next 12 hours!! :-) Thanks daniel - http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 05:05:00 +0800 Reply-To: Jorgen Wallgren Sender: HPLX Mailing List From: Jorgen Wallgren Subject: Re: 200LX 8MB <-> j720 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > > Is anyone on the list interested in swapping it for a jornada 720 (I > > already have a 690) > > I have both and would not want to swap a 200LX for a J720 ;-) > > HP Staber/Salzburg > Ha, ha, ha- one J720 cost at least 4-5 units of HP 200LX! :-) :-) Regards, Jorgen ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 17:15:20 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: 200LX 8MB <-> j720 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > Is anyone on the list interested in swapping it for a jornada 720 (I > already have a 690) What is the difference between a Jornada 680/690 and the Jornada 720? = Are they tha same size? Does software for the 680/690 also run on a 720? Is a = 720 faster? Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 17:21:21 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: Re: 200LX 8MB <-> j720 In-Reply-To: <200108252115.RAA03841@siaar2aa.compuserve.com> The processor in the 720 is faster, that is the main difference. I don't remember the exact processor speeds, you could go to the HP website for that info. I know that it wasn't that much of a difference as far as I was concerned. Both run on Windows CE. The same MS Office version is packaged in both the 690 and the 720, and that is why I still use my 690. I am very well please with my 690. When they finally decide to upgrade some of the pre-loaded software in whatever is going to replace the 720, then I might consider dropping another $1000 on that replacement. One of these days I am going to have to put my three 200LX's, my DoubleSlot and Travel Floppy that I don't use any more up for sale. Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 15:07:38 -0700 Reply-To: patrick@west.net Sender: HPLX Mailing List From: Patrick West Subject: Re: URGENT: palm pdb database -> text or gdb Comments: To: daniel.hertrich@gmx.de Mime-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Might work http://freewarepalm.net/utilities/pdbconverter.shtml PDB Converter v2.5 Size: 3926 KB Date: July 16, 2001 (Updated) Type: Freeware Min. Requirement: =95 Any hardware =95 Any OS =95 Pentium =95 Windows 98 Download: =95 pdbconverter.zip Author: Michael Verive Home: http://www.mverive.com/ Email: mverive@peoplepc.com Description: PDB Converter is a Windows 9x application designed to create,= edit, or convert between standard Palm databases (PDB) and Excel= 4 or 5 worksheets, CSV files (quoted or unquoted), and text= files (delimited or non-delimited). PDB Converter currently only works with pure string (text)= databases, but can handle PDB files of up to 16384 records, 255= fields per record, and 255 characters per field. PDB Converter uses a spreadsheet interface making it ideal for= creating or editing databases, and can run in "command-line"= mode for unattended, automatic conversions. PDB types known NOT to work with PDB Converter include HanDBase,= Jfile, MobileDB, and others that use proprietary database= formats. PDB Converter has been tested with and works well with databases= created with NSBasic/Palm, and other standard PDB files created= using PalmDB.DLL. Update Description: v2.5 (7/16/01): Added support for both standard text and tab-delimited text= files. v2.4.1 (7/15/01): On Sat, 25 Aug 2001 22:59:43 +0200, Daniel Hertrich wrote: >Hi friends, > >I'll visit the IFA (internationale Funk-Ausstellung =3D= international >broadcast exhibition, showing the new trends in entertainment >electronics and so on) here in Berlin tomorrow. > >Today I have looked for a list of exhibitors in text format to= load >it onto my LX. >Unfortunately, these idiots only have published somthing special= for >the palm and for WinCE devices. I found a file with PDB as= extension >and it indeed contains the data I need (the text is in there,= but >embedded into some weird binary stuff and very bad formatted). > >Does anyone know of a way to convert this into plain text or= maybe >even into GDB format? > >The file can be found in the zip archive http://ifa >-berlin.de/palmppc/vers1/palm/ifa2001_de.zip or in English at >http://ifa-berlin.com/palmppc/vers2/palm/ifa2001_en.zip > >I need the solution within the next 12 hours!! :-) > >Thanks daniel > >- >http://www.daniel-hertrich.de/contact > >** HPLX-L LIST Info at= http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- Patrick West, francis_patrick_west@yahoo.com on 8/25/2001 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 25 Aug 2001 19:48:55 -0400 Reply-To: Mike Schneider Sender: HPLX Mailing List From: Mike Schneider Subject: Re: 200LX 8MB <-> j720 Comments: To: Robert Hocking In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hey Robert, Where have you been hiding? In a bank? ! Anyways, regarding the 690, didn't you upgrade the OS? I'm really happy with my 720 too, but when it comes to running some of the old DOS apps, they still run faster in native on the 200LX than they do in Pocket DOS on the 720. So I guess I still need both machines. Picture this... A large pair of dockers pants, 200LX in one pocket, 720 in the other pocket. My belt doesn't work any more... now I need suspenders!!! :-) Mike... ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 00:07:38 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: new "areacode.gdb" for SUPER Comments: To: Nathalie Bugeaud MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Nathalie Bugeaud wrote: > I just finished AREACODE.GDB, listing 282 telephone area codes for North > America (USA/Canda) because the WDB list is inconvenient and incomplete for > finding locations via area codes. First column are the numbers 201 New ... Wow! I'm surprised that someone in France would go to the bother of a USA phone db; Is it something you needed? I'll take a copy too please. You might fix your garbage problem by using BDview (dbv.exe) to view the data in read only mode. I use it to view the SUPER db mainly so the db file timestamp doesn't get touched so I have an idea how old the db file is. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 08:33:00 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: A slow lighter system MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Stefan and Patrick On Sat, 25 Aug 2001 11:04:59 +0000, Stefan Peichl wrote: > Why don't you put your 200lx mainboard into your 100lx? > I did it already years ago, because I prefer the black > color of the 100lx case. > > If you know how to open the palmtop case, it is a 5 minutes > operation. Yes, this is of course the most simple operation. Swapping screens, as I suggested, needs more skills. So if you are not so familiar with the innards of the palmtop, rather swap the mainboard! :-) Thanks Stefan! daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 21:45:44 +1000 Reply-To: Alex Kamvissis Sender: HPLX Mailing List From: Alex Kamvissis Subject: POST/LX - won't "send" my emails MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----=_NextPart_000_002B_01C12E78.75A538C0" This is a multi-part message in MIME format. ------=_NextPart_000_002B_01C12E78.75A538C0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Hi, =20 I have recently had to restore my HP. Unfortunately, for some reason I = had only save an older set-up for my POSTLX. =20 I am unable to send Email.=20 =20 "SMTP ACCESS REJECTED 500 syntax error, command unrecognised" =20 My attempts to solve this problem have been fruitless. I have had it = working before with this provider. Receiving Email works fine. FAQ files have not helped. I have tried POPFirst=3D1, but still giving me this message. =20 Any assistance would be very much appreciated. =20 Alex ------=_NextPart_000_002B_01C12E78.75A538C0 Content-Type: text/html; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable
Hi,
 
I have recently had to restore my HP.=20 Unfortunately, for some reason I had only save an older set-up for my=20 POSTLX.
 
I am unable to send Email. 
 
= "SMTP=20 ACCESS REJECTED 500 syntax error, command unrecognised"
 
My = attempts to solve this problem have been fruitless. I have had it = working before=20 with this provider. Receiving Email works fine. FAQ files
 have = not=20 helped.
 
I have tried=20 POPFirst=3D1, but still giving me this message.

 
Any assistance = would be very=20 much appreciated.
 
Alex
 ------=_NextPart_000_002B_01C12E78.75A538C0-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 09:32:06 -0700 Reply-To: Joseph.Buford@HSC.COM Sender: HPLX Mailing List From: Joseph Buford Subject: Re: HPLX-L Digest - 24 Aug 2001 to 25 Aug 2001 (#2001-262) MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii >Date: Sat, 25 Aug 2001 09:13:42 -0500 >From: Scott Barrett >Subject: palm connectivity >I looked through the list archives and could not find anything like >.this, but I thought I would ask... Is there a utility that would let an >HP200 send and recieve the beam signals that the palms use? I guess I >am looking at a way to transmit and recieve the phone book and >appointment book items. I have not programmed these units, but it seems >like it could be a TSR triggered by a keystroke, maybe if you want to >send, just highlight the appt or phone book person and hit ctrl-S, >recieve could work similar. I could see am issue with data translation, >but from looking at friends palms, many fields are very similar and just >need to be pointed in the right direction. >Does this exist or is this a new idea. It sure would bring 200 users >into a broader capability. >Scott Scott, I tried to do this a couple of years ago and could not get any further that an acknowledgment that the IR's could sense each other. I believe I tried the IR.exe program from SUPER. I agree that this would extend the life of the 200lx and I would love to have something that would allow me to communicate with "The Dark side" :-) Let me know if something works for you! Joe ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 09:50:37 -0700 Reply-To: Joseph.Buford@HSC.COM Sender: HPLX Mailing List From: Joseph Buford Subject: Re: HPLX-L Digest - 24 Aug 2001 to 25 Aug 2001 (#2001-262) Comments: cc: daniel.hertrich@GMX.DE, tps-seti@WANADOO.FR MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii >Date: Sat, 25 Aug 2001 11:59:58 +0200 >From: Daniel Hertrich >Subject: Re: new "areacode.gdb" for SUPER >Hi Nathalie >On Sat, 25 Aug 2001 05:36:10 +0200, Nathalie Bugeaud >wrote: >> I just finished AREACODE.GDB, listing 282 telephone area codes for North >Oh yes, please send me a copy. :-) >> 12970 (5348 zipped) after import to a new file to eliminate 'garbage' (i >> haven't figured out how to cut garbage any other way, or why it increases >> all the time even without editing) >Do you use this "fastdb" TSR (or whatever its name is)? I think this >could cause such problems, because, AFAIK, changes in the GDB are not >really worked into the GDB, but appended, for faster processing, just >like the "fast save" option of MS Word works. >I can be wrong, since I have never used it. >GTX >daniel Daniel, Nathalie, I would love a copy of this! I have used Fastdb for many years and have has a problem only one time. Las year I was unable to back up my Appt book due to an error in the middle of the previous year. Appt book worked fine except when accessing that particular week. Some garbage was in normally good records. After I recoverd as much as I could I instituted a semi-automated backup plan and now backup use Dbcheck in a .bat file several times a week. I suspected that Fastdb MIGHT have had an effect and stopped using it for several weeks, however, the increased speed that it gives on the DS palmtop lured me back. I have had no other db problems since. I THINK that Fastdb's changes are worked into the db but only upon closing of the file instead of concurrent to running the db. See Ya Joe ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 09:57:24 -0700 Reply-To: Joseph.Buford@HSC.COM Sender: HPLX Mailing List From: Joseph Buford Subject: Re: HPLX-L Digest - 24 Aug 2001 to 25 Aug 2001 (#2001-262) Comments: cc: sabarrett@BPSINET.COM, palmtop@N-LINK.COM MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii >Date: Sat, 25 Aug 2001 09:13:42 -0500 >From: Scott Barrett >Subject: palm connectivity >I looked through the list archives and could not find anything like >.this, but I thought I would ask... Is there a utility that would let an >HP200 send and recieve the beam signals that the palms use? I guess I >am looking at a way to transmit and recieve the phone book and >appointment book items. I have not programmed these units, but it seems >like it could be a TSR triggered by a keystroke, maybe if you want to >send, just highlight the appt or phone book person and hit ctrl-S, >recieve could work similar. I could see am issue with data translation, >but from looking at friends palms, many fields are very similar and just >need to be pointed in the right direction. >Does this exist or is this a new idea. It sure would bring 200 users >into a broader capability. >Scott >Date: Sat, 25 Aug 2001 15:33:10 -0500 >From: Tim >Subject: LX <--> Palm via IR >Hi all, >Anyone having any luck beaming documents, files, etc. between a PalmOS >device and a 200LX (or any LX for that matter)? >I tried some of the "Super" downloads, some time ago.... One had some >command/features like "oput" and "oget" I think, but didn't have any luck. >Any help would be appreciated.... >--tim >Also, if I can beam, can I CONVERT say, a .WK1 spreadsheet into something >the Palm can use (or vice-versa)? Scott,Tim, I tried to do this a couple of years ago and could not get any further that an acknowledgment that the IR's could sense each other. I believe I tried the IR.exe program from SUPER. I agree that this would extend the life of the 200lx and I would love to have something that would allow me to communicate with "The Dark side" :-) Let me know if something works for you! Joe ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 13:01:48 -0400 Reply-To: ashoni arora Sender: HPLX Mailing List From: ashoni arora Subject: 200lx 8MB <-> j720 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit MIME-Version: 1.0 Hi all just so you know I just picked up a j720 on e-bay for $340 Im sure I can get more for a 200LX DS 8MB with SC etc etc Thaddeus wants about $800 for such a unit -- ashoni arora ashoni@onebox.com - email (212) 894-3702 x4073 - voicemail/fax __________________________________________________ FREE voicemail, email, and fax...all in one place. Sign Up Now! http://www.onebox.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 12:00:27 -0600 Reply-To: Richard and Patti Smith Sender: HPLX Mailing List From: Richard and Patti Smith Organization: Orion On-Site Computer Services Subject: Re: ÝFwd: REX.net service ends August 31, 2001¨ MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit >KenLondon wrote: >>Martin Bergvill wrote: >> Saw something about a lawsuit against them somewhere.. People are not >> happy because they bought the Rex6000 based on what it could dowload >> from the rex.net. >snip< >Also I have a rex and saw nothing about rex.net in the >material included with the device. Where did you learn about >this rex.net? ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 12:08:23 -0600 Reply-To: Richard and Patti Smith Sender: HPLX Mailing List From: Richard and Patti Smith Organization: Orion On-Site Computer Services Subject: Re: ÝFwd: REX.net service ends August 31, 2001¨ MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Sorry about the previous message like this one, I hit Send too soon! >KenLondon wrote: >Also I have a rex and saw nothing about rex.net in the >material included with the device. Where did you learn about >this rex.net? Rex.net was created especially for the Rex 6000 series -- or maybe it was the other way around -- anyway, it was supposed to be a portal for Rex users where one could download web content to the Rex 6000. It was promoted in the Rex 6000 literature. It worked pretty well for a little while -- about 2 weeks. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 21:32:30 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Siemens ME45 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, has anyone ever seen the mobile phone ME45 by Siemens? I have never seen that one before, even on Siemens' website when I browsed it a few weeks ago. It is a GPRS capable phone. I just have had the chance to connect it to my LX on the IFA Berlin (sitting in the train back home now), but I couldn't get it to work. I tried tmyy self-made data cable, which fits nicely into the phone, and I tried via IrDA. WWW/LX said (when trying to establish a normal GSM data connection with the same settings I also use for my Siemens S35i): connectong to hanging up when I tried the cable. When I tried IrDA it said connecting to and nothing more. I had to abort the online run with CTRL. Then a short "talking to SIEMENS ME45" appeared, but disappeard again and WWW/LX aborted. Strange, isn't it? Maybe the cable port is not compatible? But Setcom.bat (or better modem.com) recognized the modem at the COM port. And why should IrDA refuse to work, if only the cable port wasn't compatible. So it has to be something else. I hope to get another chance to test this phone more extensively in the future. Martin, do you have a chance to test this phone? GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 22:32:02 +0100 Reply-To: HP Staber Sender: HPLX Mailing List From: HP Staber Subject: Re: 200lx 8MB <-> j720 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > just so you know I just picked up a j720 on e-bay for $340 > Im sure I can get more for a 200LX DS 8MB with SC etc etc > Thaddeus wants about $800 for such a unit > > -- > ashoni arora Good luck. Let's share our frustrations :-} HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 08:55:27 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: ROBOWEB 1.1 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Mon, 27 Aug 2001 08:40:43 +1200 (NZT) Available at: http://www.geocities.com/aghutchins/roboweb.zip Same functionality as before, but much faster to start digging. Some additional built-in features, for weather and quotes. Now works over IrDA - thanks to Andreas for a new ROBOT.EXE! Start with README.TXT, and RWEBFAQ.DOC. Previous users need to read RWHIST.DOC. - Tony ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 17:09:45 -0400 Reply-To: Suresh Nirody Sender: HPLX Mailing List From: Suresh Nirody Subject: OT Smart Media problem MIME-Version: 1.0 Content-Transfer-Encoding: quoted-printable Content-Type: text/plain; charset=ISO-8859-1 I have two 128MB Smart Media cards of pics I took during my vacation, but= am unable to read them. When I pop them in my ActionTec card reader (that= rhas slots for PC cards, Compact Flash, and Smart Media) it won't recogni= ze them. (Tried this at home and at work with 2 different ActionTec on 2 different computers, no luck, tho they read PC Cards and Compact Flash OK= , so seem to be working....) When I pop them into my Microtech Digital Flas= h Film card (converter to PC Card format) and put that into my 200lx or int= o the card readers I still can't read them.... Any ideas of what might be wrong?? Both these methods have worked for me in the past, albeit with other, smaller Smart Media cards, not the two in question.... Suresh ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 09:45:18 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: POST/LX - won't "send" my emails MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Mon, 27 Aug 2001 09:27:36 +1200 (NZT) 09h41m52s ago ... On Sun, 26 Aug 2001 21:45:44 +1000, Alex Kamvissis wrote: > "SMTP ACCESS REJECTED 500 syntax error, command unrecognised" That's a pretty hard error. Ther server could have really old software that does not recognise "EHLO". If so, adding ESMTP=0 to the mailbox section should help. Hope so :) This is from tip #7 in "Tips 'n Tricks" at www.dasoft.com. - Tony ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sun, 26 Aug 2001 19:47:04 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Backup with automated dbcheck and alert Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Sorry for the lateness of this reply, but after I read the request from you, my brain started cooking. Today I took a 2 hour walk on the beach and POP!!! There it was... To summarize: You know that the dbcheck/backup process succeeds or fails based on dbcheck. You want a notification in the palmtop, such a the Daily Greetings of apptbook. So... Run the dbcheck. If success, create a file, and the text: " backup successful." Save the file. If failure: prepare the same filename and text: " backup failed." . Have the backup batch file save this file using the same location, the same filename. Schedule an appointment each day, some significant time AFTER the end of the backup, and in that appointment run a macro. This macro opens an appointment, and opens the note (F3), insert file (F3 providing the filename of the message. The cursor ends up at the end of the added text, so entetr SHIFT-CTRL-Home to marke the entire text, cut it, F10 to close note, Alt-R to return to the Description field, and paste the note. Save the appointment. When you next open the palmtop, Daily Greeting will have that message there as an event. The only question I am not sure of is this: Say you schedule this to take place at 3am. Does opening an apptbook from a macro awakened constitute a "first open" i.e. will daily greeting show up then, but not again when you wake up at 6am and power up the Palmtop? To help in that, look for GREET.ZIP. Andreas wrote this in 1994, and it conrols the daily greeting timing. You can find it in ftp://ftp.dasoft.com/pub/MISC/greet.zip ... Enjoy. Oh,,, here is a macro to advance a specific appointment forward by one day (or more): Could be adapted to advance more than one appointment.... {Appt}{F9}{F5}{F4}{Left}{F4}|a:\batch\bakup.bat{Enter}{Enter}{Alt+T}4.00{A= lt+D}+{F10}{Menu}q{Appt}{F9}{F5}{F4}{Left}{F4}||9{Enter}{Enter}{Alt+T}4.30= {Alt+D}+{F10}{Menu}q This one advances a batch file execution appointment and a macro (itself, actually) to the next day. {Appt}{F9} - open appt, make sure it is in appt view {F5}{F4}{Left} - Goto today, to make sure, then move to yesterday. {F4}|a:\batch\bakup.bat{Enter} -- search for the string "a:\batch\bakup.bat". {Enter} -- enter that appointment. {Alt+T}4.00{Alt+D}+{F10} -- Go to time field and enter 4.00 am, in case it was manually changed in the prior day. Go to date field, and add 1 to the date. Save. {Menu}q -- Quit the apptbook. The next part is a repeat, but now searching for "||9" the macro I want to move forward. The time is 30 minutes later. {Appt}{F9}{F5}{F4}{Left}{F4}||9{Enter}{Enter}{Alt+T}4.30{Alt+D}+{F10}{Menu= }q Hope this is helpful. Avi ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 15:15:55 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: POST/LX - won't "send" my emails Comments: To: Alex Kamvissis MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Mon, 27 Aug 2001 14:56:57 +1200 (NZT) Hi Alex, Oh that's good, the ESMTP=0 must have worked. Sorry I am not too good on modems. Maybe someone else here can help. If you are using the serial port have a look at the pins and see if one is bent or something. I had a serial cable fail on me recently too. If it's a card modem, I'd recommend using Stefan's LXCIC to initialise it. If you get no response from an AT then, basically the comms program can't see the modem at all. Either that, or the modem is on-line and not in command mode, so the AT is not interpreted as such, it is just sent down the line :) Oh! You do get "Busy" or "no dialtone" - that's good! :) It could be your wife is on the phone?. Or, it could be something else - maybe try ATX3DT1122 instead - the X3 should cause the modem to dial, even if no dialtone can be detected. - Tony 03h01m49s ago ... On Mon, 27 Aug 2001 09:55:08 +1000, Alex Kamvissis wrote: > Thanks Tony, > > I have been trying to test the program when I came up > against another frustrating hurdle. > > Occasionally, my 200LX doesn't pick up the dial tone. I > have gone into the HP COM & tried AT&V which lists the modem > settings & everything looks ok. I have tried the modem with > a spare 200LX and works fine. When I try an ATDT1122 for > a test. Nothing, either "Busy" or no "dial tone". >> Usually when the power on\off, I could hear a click that > I assume is the dial tone. Not anymore. Could it be the > COMM loaded in at Boot up. Tried a couple of Ctl Alt Del, > but nothing. >> Any thoughts. >> Alex >> > > "SMTP ACCESS REJECTED 500 syntax error, command > > > unrecognised" > > > > That's a pretty hard error. Ther server could have really > > old software that does not recognise "EHLO". If so, adding > > > > ESMTP=0 > > > > to the mailbox section should help. Hope so :) > > > > This is from tip #7 in "Tips 'n Tricks" at > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 01:59:43 -0400 Reply-To: Alex Kamvissis Sender: HPLX Mailing List From: Alex Kamvissis Subject: POSTLX & Not SENDING MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Tony your a wiz, Thanks very much. ESMTP=0 worked. Yippeee. after at least 2 months of many wasted hours. Now I can say, written on a 200LX. I would be interested to know what ESTMP=0 does, for future reference. Regards one very greatful person ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 10:01:03 +0200 Reply-To: Lasse Karlsson Sender: HPLX Mailing List From: Lasse Karlsson Subject: Re: MM/LX forgets maps-dir Comments: To: sponsor@FTEL.NET MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Avi wrote: > I think this was just fixed in MM/LX 1.1a uploaded last night > (Friday, 24 Aug) Mind trying it and give feedback again? Check That's correct. Now it's ok after invoking external programs. But.... one minor cosmetic bug remains. Try this in the example app. Press e to go to meetings Press m for more meetings Don't press ENTER instead press ESC. MM/LX gives an error message "invalid lin meeting.mm" Kind regards Lasse in Stockholm Sweden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 20:42:17 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: POSTLX & Not SENDING MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Mon, 27 Aug 2001 20:17:31 +1200 (NZT) 02h17m48s ago ... On Mon, 27 Aug 2001 01:59:43 -0400, Alex Kamvissis wrote: > ESMTP=0 worked. Yippeee. after at least 2 months of many > wasted hours. Alex - I pleased that was it! > I would be interested to know what ESTMP=0 does, for future > reference. Instead of greeting the server with "EHLO", POST.EXE says "HELO", when ESMTP=0. Most SMTP servers do understand "EHLO", but clearly some don't. Looks like your bigpond.com SMTP uses "Netscape Messaging Server 4.15", and it is not programmed to understand "EHLO" so reports a syntax error. That's strange because I'm sure I've seen earlier versions (4.05) that do ESMTP. Most servers don't mind "EHLO" - but very few actually *do* ESMTP. GMX.NET is one that does - which is great because you can use any ISP and still send through GMX.NET - with ESMTP the authentication is done based on Login/password. The "Tips and Tricks" section at www.dasoft.com has a section on this. - Tony ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 11:28:30 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: POSTLX & Not SENDING MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit > Tony your a wiz, Yes indeed, Tony is a wiz. Kind regards Helmuth ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 06:58:35 -0500 Reply-To: TomSalwasser@COMPUSERVE.COM Sender: HPLX Mailing List From: Tom Salwasser Subject: FLUFF:Items for Sale MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit Hello! Cool stuff on eBay: Tripmate GPS (works with lx): http://cgi.ebay.com/aw-cgi/eBayISAPI.dll?ViewItem&item=1269041971 Parallax Basic Stamp Development Kit: http://cgi.ebay.com/aw-cgi/eBayISAPI.dll?ViewItem&item=1269031870 Regards, Tom ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 06:33:26 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: OT Smart Media problem MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > I have two 128MB Smart Media cards of pics I took during my vacation, but > am unable to read them. When I pop them in my ActionTec card reader (that > rhas slots for PC cards, Compact Flash, and Smart Media) it won't recognize > them. (Tried this at home and at work with 2 different ActionTec on 2 > different computers, no luck, tho they read PC Cards and Compact Flash OK, > so seem to be working....) When I pop them into my Microtech Digital Flash > Film card (converter to PC Card format) and put that into my 200lx or into > the card readers I still can't read them.... Any ideas of what might be > wrong?? Both these methods have worked for me in the past, albeit with > other, smaller Smart Media cards, not the two in question.... 128mb Smart Media was a recent thing, wasn't it? Another list member mentioned having occasional problems with Smart Media adapters (floppy or PCMCIA) when the cards were "large". Since the adapters (or readers) must have the controller "smarts" built into them (vs CF which was engineered with on-board controllers), it's possible the readers/adapters were made before 128mb SM was widely available and the manufacturers may have only designed for the cards on the market at the time. Just a guess. More importantly, since your camera obviously works with your 128mb cards, you should just use whatever cable connection is available to first backup your pics. Check with the vendor for the cards and see what reader/adapter they suggest, or contact the reader/adapter manufacturer to see if your model supports 128mb. - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 10:26:00 -0400 Reply-To: Bob Penick Sender: HPLX Mailing List From: Bob Penick Subject: OT - Possible Psion 5mx / MC 218 List server MIME-version: 1.0 Content-type: text/plain; charset=iso-8859-1 Content-transfer-encoding: 7bit I recently found an Ericsson MC218 (a Psion 5mx clone) at a reasonable price on eBay. I bought it to play with based on comments I've read on this list (Owen?). Does anyone know of a support list for the 5mx that is similar to this or the Omnibook list? Thanks in advance, bob PS - Interesting, but it will never replace my 200lx. This one will end up in the wife's possession because she likes it. It's just that I'll have to support it. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 10:49:19 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: URL for dload (was: new "areacode.gdb" for SUPER In-Reply-To: <00cd01c12d19$68dc87c0$31e9f8c1@oemcomputer> MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hi, I told Nat I would keep the gdb file in my corner of cyberspace so she wouldn't have to keep emailing it. http://epadin.freeshell.org/stuff/ Until super comes back (if ever) I'm willing to keep more stuff there so, let me know. I think I can put as much as 60MB of stuff there. I seem to recall an lxmap with area codes. I'm sure it's out of date by now, tho. > -----Original Message----- > From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu¨On > Behalf Of > Nathalie Bugeaud > Sent: Friday, August 24, 2001 11:36 PM > To: HPLX-L@uconnvm.uconn.edu > Subject: new "areacode.gdb" for SUPER > > > I just finished AREACODE.GDB, listing 282 telephone area > codes for North > America (USA/Canda) because the WDB list is inconvenient snip > Since the SUPER site is temporarily down, you may ask me ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 07:56:38 -0700 Reply-To: kopplin@TECHNOIR.NU Sender: HPLX Mailing List From: Mike Kopplin Subject: MM/LX display bug MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Using the latest mm.exe with meeting.mm from Helmuths example map there is a problem displaying the items in the first meeting. Zooming displays correctly, but in regular mode the items overlap. If I delete either of the children from the Todos entry it displays correctly. Adding a second Todos child to the second meeting causes this one to overlap also. Mike Kopplin ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 14:49:22 +0000 Reply-To: armada1@ATTGLOBAL.NET Sender: HPLX Mailing List From: Jose Manuel Armada Dacal MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hello - All, Does HP still provide migration tools for the HP200LX built-in apps. when you purchase one of their WinCE machines?. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 11:35:57 -0400 Reply-To: KenLondon Sender: HPLX Mailing List From: KenLondon MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit >Jose Manuel Armada Dacal wrote: >Does HP still provide migration tools for the >HP200LX built-in apps. when you purchase one of >their WinCE machines?. Have an hp680 and an hp545, they provide no help in this respect. Do yourself a favor, don't get a CE device. Upgrade your 200lx, you'll be happier in the long run. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 19:38:25 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Backup with automated dbcheck and alert MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Avi, On Sun, 26 Aug 2001 19:47:04 -0700, Avi Meshar wrote: > Sorry for the lateness of this reply, but after I read the > request from you, my brain started cooking. Today I took a 2 > hour walk on the beach and POP!!! There it was... > > Ý...¨ > > Hope this is helpful. Indeed it IS! :-) Thank you so much, Avi. This seems to be the ideal solution. I hae got suffestions to let sppointment book open the created file in a text viewer in the morning, Also a noce idea, but if a text editor is open, and I don't take care about the used memory, the alarm clock refuses to ring in the morning! So what then? I have to hurry, don't have time to read the results of the backup, close the viewer, and so I also could have not let it display the results at all. ;-) I'll try your solution and report! GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 11:15:48 -0700 Reply-To: Ian Butler Sender: HPLX Mailing List From: Ian Butler Subject: Re: URL for dload (was: new "areacode.gdb" for SUPER In-Reply-To: MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Mon, 27 Aug 2001, Ed Padin wrote: > Until super comes back (if ever) I'm willing to keep more stuff there > so, let me know. I think I can put as much as 60MB of stuff there. SUPER is not down. It never was. There was a problem with the perl script that automatically processes updates, but it's been fixed for a while now. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 16:07:24 -0400 Reply-To: Ed Padin Sender: HPLX Mailing List From: Ed Padin Subject: Re: URL for dload (was: new "areacode.gdb" for SUPER In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Oh, sorry. I made an assumption without checking. I know that Mitch Hamm doesn't run it anymore and the Dave Sargeant has been MIA for a while. I even remember a few times in the past where I could not access it. It seems to be okay now, tho. > -----Original Message----- > From: HPLX Mailing List Ýmailto:HPLX-L@uconnvm.uconn.edu¨On > Behalf Of > Ian Butler > Sent: Monday, August 27, 2001 2:16 PM > To: HPLX-L@uconnvm.uconn.edu > Subject: Re: URL for dload (was: new "areacode.gdb" for SUPER > > > On Mon, 27 Aug 2001, Ed Padin wrote: > > > Until super comes back (if ever) I'm willing to keep more > stuff there > > so, let me know. I think I can put as much as 60MB of stuff there. > > SUPER is not down. It never was. There was a problem with the perl > script that automatically processes updates, but it's been > fixed for a > while now. > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 20:52:14 -0000 Reply-To: vmbeazel@SWCP.COM Sender: HPLX Mailing List From: Victor Beazel Subject: Compact Flash Too Thick This is my first posting to this group. Hope it works - I could sure use your help. I just bought a Sandisk 160MB CF memory card from Ebay to use in my HP100LX. I also bought a PC Card Adapter from another party. When I received both, I realized that the card would not fit into the adapter. It is too thick! I am hoping that the CF card seller can help me find a suitable resolution. However, what I am hoping this group can help me with is how to read the specifications and know that what I am ordering will work on the HPLX. Thanks in advance for any help you can provide, Victor Beazel ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 16:10:12 -0500 Reply-To: Bryan Biggers Sender: HPLX Mailing List From: Bryan Biggers Subject: Re: Compact Flash Too Thick MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Oh, oh, sounds like you bought a Type II version of CF and a type I adapter. Didn't someone say that type II would fit in if you had a CF to Type II adapter? Bryan Victor Beazel wrote: > > This is my first posting to this group. Hope it works - I could sure use > your help. I just bought a Sandisk 160MB CF memory card from Ebay to use in > my HP100LX. I also bought a PC Card Adapter from another party. When I > received both, I realized that the card would not fit into the adapter. It > is too thick! I am hoping that the CF card seller can help me find a > suitable resolution. > > However, what I am hoping this group can help me with is how to read the > specifications and know that what I am ordering will work on the HPLX. > > Thanks in advance for any help you can provide, > Victor Beazel > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 16:16:56 -0500 Reply-To: Orin Keplinger Sender: HPLX Mailing List From: Orin Keplinger Subject: Smart media problem MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit My action tec card reader required no modifications to read 128 smart media cards. I did notice a much longer delay before the card contents were read into explorer, etc. I attributed this to the larger size of the card. Orin ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 21:21:22 -0000 Reply-To: vmbeazel@SWCP.COM Sender: HPLX Mailing List From: Victor Beazel Subject: Re: Compact Flash Too Thick In-Reply-To: <3B8AB734.A5F0AED2@charter.net> Bryan Biggers said: > Oh, oh, sounds like you bought a Type II version of CF and a type > I adapter. Didn't someone say that type II would fit in if you > had a CF to Type II adapter? Bryan > You are correct. I confused PCMCIA Type II with CF Type II. I don't think CF Type II will fit at all. I held the CF up to the PCMCIA slot and it looks too thick to me. Victor ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 15:27:41 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: Compact Flash Too Thick MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > You are correct. I confused PCMCIA Type II with CF Type II. I don't think > CF Type II will fit at all. I held the CF up to the PCMCIA slot and it looks > too thick to me. CF Type II will fit, with the right adapter. My IBM Microdrive is CF Type II and it came with said special PCMCIA adapter which fits in the 200LX slot. Both card and adapter are the same thickness. - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 00:37:53 +0000 Reply-To: Stefan.Peichl@T-ONLINE.DE Sender: HPLX Mailing List From: Stefan Peichl Subject: Re: A slow lighter system MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Patrick West wrote: > I don't see how to disconnect the screen ribbon cable from the board = and swap boards. that's very simple: the ribbon cable is pressed on the mainboard through a slider connector. You only have to open the slider and then you just remove the cable either by hand or with a pencil, which you put into the hole in the middle of the cable. Visit a site with photos like Daniel Hertrich's or David Sergeant's site with their very good explanations. Stefan ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 22:41:25 -0000 Reply-To: vmbeazel@SWCP.COM Sender: HPLX Mailing List From: Victor Beazel Subject: Re: Compact Flash Too Thick In-Reply-To: Longden said: > > CF Type II will fit, with the right adapter. > > My IBM Microdrive is CF Type II and it came with said special PCMCIA > adapter which fits in the 200LX slot. Both card and adapter are the same > thickness. > > - Longden > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > Thanks for the welcome news. I start looking around for a Type II adapter. Victor ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 00:30:04 +0100 Reply-To: Paulo Custodio Sender: HPLX Mailing List From: Paulo Custodio Subject: OL2LX 3.03: converting phone book limits? MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Is there a limit in the number of phone book records converted from the HPLX to Outlook by Curtis Cameron's OL2LX 3.03? I have about 300 records in my HPLX phone book database, and when converting to Outlook 97, only 167 records appear in Outlook (apparently the older records). Thanks to Curtis for this excelent addition to our HPLX tool set. Paulo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 05:40:28 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: David who runs the SUPER site MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit David who runs the SUPER site commented: >SUPER is not temporarily down ... it never was. The people who >have said otherwise were wrong. >To submit your new software, send it to super@palmtop.net. i sent areacode.gdb, but for the third time received this back: ----- The following recipients were processed by MTA magnolia.wanadoo.fr... super@palmtop.net; Action: Failed; Status: 5.1.1 (bad destination mailbox address) Remote MTA palmtop.net: SMTP Diagnostic 550 5.1.1 ... User unknown ---- Message SMTP Diagnostic: 554 DATA Transaction failed, no recipients given so, SUPER ... IS ... down ?!? nat ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 05:42:44 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: GDB garbage, was Re: new "areacode.gdb" for SUPER MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Daniel asked: >Do you use this "fastdb" TSR (or whatever its name is)? I think >this could cause such problems, because, AFAIK, changes in the GDB >are not really worked into the GDB, but appended, for >faster processing, just like the "fast save" option of MS Word works. i am not sure if it is loaded or not; the instructions say to put fastdb.tsr into C:\_dat, but my autoexec.bat does not have this directory in its path and Russ commented: >Wow! I'm surprised that someone in France would go to the bother of >a USA phone db; Is it something you needed? I'll take a copy too please. often message signatures show just a fax number, and i wanted to know where they come from (i have special interest in states with native American connections ie. Indian Health Service 'IHS') >You might fix your garbage problem by using BDview (dbv.exe) I use it too, but it doesn't reduce db file sizes which grow each time they are opened. I have not found a way to reduce them but to import them into a new file. Unfortunately DBview won't list subsets until they are used in the Apps.DB program. Maybe Ed Keefe could point us to an issue of the Palmtop paper where this is discussed. and Joe requested: >I would love a copy of this! Ed Padin put it on his site to download >I THINK that Fastdb's changes are worked into the db but only >upon closing of the file instead of concurrent to running the db. closing the GDB application doesn't reduce the file's size at all - it actually increases it each time for example, the original areacode.gdb is only 12k, but mine has now swollen to 37k by just opening and closing it without any editing. If it gets too much, i import it into a new file and it will be again 12k, but then DBview won't give me subsets. any way out? nat ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 05:45:27 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: Subject: MM/LX 1.1a Uploaded to D&A Site MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Avi wrote: >Folks, FYI: MM/LX version 1.1a uploaded to D&A Website >last night. This version has just one small bug fix. For 2 days now i am 'testing' v1.1a running it via maxdos ... no data losses yet! I really miss the "abandon" :) After a few losses of links due to entering note text (and getting warned: ERROR - Invalid Link #.....) and after creating 2 files within the same file, the second file showing garbled text in place of a child (without note), i created a menu with all the number and letter keys of the LX keyboard as hotkeys. Now i have to add links to all those potential maps :) ...nat ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Mon, 27 Aug 2001 21:25:55 -0700 Reply-To: Ian Butler Sender: HPLX Mailing List From: Ian Butler Subject: Re: David who runs the SUPER site In-Reply-To: <002501c12f79$8059c680$5721fac1@oemcomputer> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Tue, 28 Aug 2001, Nathalie Bugeaud wrote: > David who runs the SUPER site commented: > > >SUPER is not temporarily down ... it never was. The people who > >have said otherwise were wrong. > >To submit your new software, send it to super@palmtop.net. > > i sent areacode.gdb, but for the third time received this back: > > so, SUPER ... IS ... down ?!? The super@palmtop.net address was set to reject any messages with attachments a couple of weeks ago, when the SirCam virus was going around and the address was getting multimegabyte virus messages from everybody who ever visited SUPER and then infected their computer with SirCam by clicking on an infected attachment. Now that things have quieted down, the address is accepting attachments again. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 00:16:36 -0500 Reply-To: Curtis Cameron Sender: HPLX Mailing List From: Curtis Cameron Organization: None Subject: Re: MM/LX display bug Comments: To: kopplin@TECHNOIR.NU In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit On Mon, 27 Aug 2001 07:56:38 -0700 Mike Kopplin wrote: >Using the latest mm.exe with meeting.mm from Helmuths example >map there is a problem displaying the items in the first >meeting. Zooming displays correctly, but in regular mode the >items overlap. If I delete either of the children from the Todos >entry it displays correctly. Adding a second Todos child to the >second meeting causes this one to overlap also. I saw this as well with my own map. One of the children of the main item was on the left side, but its children displayed to the right, interfering with the main item and its children which were displayed on the right side. -- Curtis Cameron WGS-84 N33.033 W96.724 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 00:19:46 -0500 Reply-To: Curtis Cameron Sender: HPLX Mailing List From: Curtis Cameron Organization: None Subject: Re: OL2LX 3.03: converting phone book limits? Comments: To: Paulo Custodio In-Reply-To: <3B8AD7FC.BE610FF5@yahoo.com> MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit On Tue, 28 Aug 2001 00:30:04 +0100 Paulo Custodio wrote: >Is there a limit in the number of phone book records converted from the >HPLX to Outlook by Curtis Cameron's OL2LX 3.03? > >I have about 300 records in my HPLX phone book database, and when >converting to Outlook 97, only 167 records appear in Outlook (apparently >the older records). I've heard of this before, and the cause then was a corrupted database. Have you DBCHECKed it? And in that case, the owner e-mailed me the file, which I was able to recover. I've had quite a bit of success recovering corrupted files that Garlic can't fix, so if anyone needs help, let me know. -- Curtis Cameron WGS-84 N33.033 W96.724 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 00:29:41 -0500 Reply-To: Curtis Cameron Sender: HPLX Mailing List From: Curtis Cameron Organization: None Subject: Re: GDB garbage, was Re: new "areacode.gdb" for SUPER Comments: To: Nathalie Bugeaud In-Reply-To: <002601c12f79$81cb09c0$5721fac1@oemcomputer> MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit On Tue, 28 Aug 2001 05:42:44 +0200 Nathalie Bugeaud wrote: >closing the GDB application doesn't reduce the file's size at all - it >actually increases it each time > >for example, the original areacode.gdb is only 12k, but mine has now swollen >to 37k by just opening and closing it without any editing. If it gets too >much, i import it into a new file and it will be again 12k, but then DBview >won't give me subsets. When a GDB file is open, the LX keeps a table in memory with pointers to each record in the database, but the actual file doesn't contain that table. When you close it, the LX writes the lookup table at the end of the file, so that it will be able to find all the records quickly next time, but as a result the file will be larger. It should be larger by about eight bytes times the number of records - there is one record for each data item, one for each note, one for each field in the database, and two for each subset that's defined. If you have FASTDB.TSR in C:\_DAT, I believe even if that directory is not in your path, then it will wait until you've accumulated at least three garbage records before it cleans them out. Maybe those three that aren't being deleted are lookup tables, which can be somewhat large. Could you send me these files, where one is about 12k, and another supposedly identical one is 37k? I'd like to see what it is. -- Curtis Cameron WGS-84 N33.033 W96.724 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 02:41:29 -0400 Reply-To: Martin Bergvill Sender: HPLX Mailing List From: Martin Bergvill Subject: Re: Siemens ME45 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit On Sun, 26 Aug 2001 21:32:30 +0200, Daniel Hertrich wrote: > Hi friends, Hello there.. > has anyone ever seen the mobile phone ME45 by Siemens? I have seen some pictures, but I am bit behind with everything. > Martin, do you have a chance to test this phone? We have some orders in..not sure when we get it. I will test it when we get it. But it will be irda only. I do not think I have any datacables at work. I have also ordered the Nokia 8310.. Will test that one too when I get it. Soon it will be wintertime here and my motorcycle will be parked. I plan to do some more testing then. Regards -- Martin Bergvill ,Narvik Norway ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 00:12:42 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: MM/LX Version 1.1 Uploaded. MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Folks, I posted a few days ago about MM/LX 1.1 upload. Among others, I wrote this: > The price has changed. If you have a license for MM/LX please > READ the information on the updates page - it may be worth > your time.. This is a mistake! The price has NOT CHANGED. All current licensees of MM/LX can download the new version and use it with no limitation. Those of you who have not yet purchased a license for this exciting program, please do so ... The second part of the paragraph refer to current licensees: If you currently have a license, read the the info in the updates so when you UNPACK the updated package you do not lose the current configuration. I apologize if this caused a confusion to anyone. Avi Meshar D&A Software http://www.dasoft.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 00:46:33 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Compact Flash Too Thick Comments: To: Bryan Biggers MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Bryan Biggers wrote: > Oh, oh, sounds like you bought a Type II version of CF and a type > I adapter. Didn't someone say that type II would fit in if you > had a CF to Type II adapter? Bryan CF Type II should fit fine in the 200LX. I used a IBM Microdrive 1GB which is a Type II CF and it fits fine with its adapter. There may be something else going on. I wonder if Sandisk deviated from the standard? Avi ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 10:30:00 +0200 Reply-To: Etienne Lemaire Sender: HPLX Mailing List From: Etienne Lemaire Subject: Re: TECH Comments: To: Bing Xu MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I have Windi7, a 7 language dictionary that works on the palmtop. Installed, it requires about 2MB per language- not very extensive, used to be a free download, I can sentd it if required HTH Etienne ----- Original Message ----- From: Bing Xu To: Sent: Wednesday, August 22, 2001 05:42 PM Subject: TECH Any info about 200lx's working with QCP2760 (QualComm 3-mode CDMA cellphone)? And where to buy or download Webster or other English dictionaries for 200lx? Thanks a lot. Bing Canada ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 07:11:16 -0400 Reply-To: I Al-Khars Sender: HPLX Mailing List From: I Al-Khars Subject: Re: TECH Comments: To: stelem@attglobal.net Mime-Version: 1.0 Content-Type: text/plain; format=flowed Does it contain ARABIC language Al-Khars >From: Etienne Lemaire >Reply-To: Etienne Lemaire >To: HPLX-L@UConnVM.UConn.Edu >Subject: Re: TECH >Date: Tue, 28 Aug 2001 10:30:00 +0200 > >I have Windi7, a 7 language dictionary that works on the >palmtop. Installed, it requires about 2MB per language- not very >extensive, used to be a free download, I can sentd it if >required > >HTH > >Etienne >----- Original Message ----- >From: Bing Xu >To: >Sent: Wednesday, August 22, 2001 05:42 PM >Subject: TECH > > >Any info about 200lx's working with QCP2760 (QualComm 3-mode >CDMA cellphone)? And where to buy or download Webster or other >English >dictionaries for 200lx? Thanks a lot. > >Bing >Canada > >** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > _________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 13:20:27 +0200 Reply-To: Etienne Lemaire Sender: HPLX Mailing List From: Etienne Lemaire Subject: Re: TECH(7 language dictionary) Comments: To: I Al-Khars MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit No luck: English, Spanish,French, Italian, Portuguese, German, Dutch Etienne ----- Original Message ----- From: I Al-Khars To: Sent: Tuesday, August 28, 2001 01:11 PM Subject: Re: TECH | Does it contain ARABIC language ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 09:35:04 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: Print MM-screen? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Is there a way to print the screen of mm/lx? Uli ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 17:14:41 +0200 Reply-To: Josef Meyer Sender: HPLX Mailing List From: Josef Meyer Subject: ROBOWEB/LX error message Comments: To: tony.hutchins@attglobal.net MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Today I installed the new ROBOWEB/LX files on my HPLX. I made the setup according to the instructions in Readme.txt, i.e. I used only the POST/LX settings in post.cfg, but nothing in robot.cfg. From the predefined settings in rweb.o I selected the weather for Munich and sent this "mail". During "sending" I got several error messages which were too fast to read, but at the end the following one stayed on the screen: ROBOT/LX Error: Cannot have RControl=1 and no Post= in ÝHTTP¨ (Line 15 in file SCR\RWEBINIT.SCR) But at the end I found in my Inbox the requested wheather forecast! Do I have a fault in my setup (but I followed strictly the instructions in readme.txt), or is something else not correct? Josef Meyer ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 17:29:15 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: Print MM-screen? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Ulrich, > Is there a way to print the screen of mm/lx? > Uli Make a screen copy using e.g. caplx, which creates a pcx file. You may print this result from any desktop. Kind regards Helmuth ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 11:36:27 -0400 Reply-To: Bing Xu Sender: HPLX Mailing List From: Bing Xu Subject: Holidays MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII Any software of American and Canadian holidays and being able to integrate into the AppointmentBook? BTW, my rechargable NiCd batteries can not be charged to 3.09v to which I set in the ABC, but only to 2.8v then drop. Does this do harm to my hp200, or do I have to replace a new pair of batteries? Thanks. Bing ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 16:17:44 -0000 Reply-To: vmbeazel@SWCP.COM Sender: HPLX Mailing List From: Victor Beazel Subject: Re: Compact Flash Too Thick In-Reply-To: <200108280746.AAA31910@ftel.net> Avi Meshar said: > CF Type II should fit fine in the 200LX. I used a IBM > Microdrive 1GB which is a Type II CF and it fits fine with its > adapter. I just talked to SanDisk about an adapter for a Type II CF, and they said that they have not come out with one yet. Those of you who are using Type II CF in the 200LX, where did you find your PC Card Adapter? Victor ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 10:16:38 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: Compact Flash Too Thick MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > I just talked to SanDisk about an adapter for a Type II CF, and they said > that they have not come out with one yet. Those of you who are using Type II > CF in the 200LX, where did you find your PC Card Adapter? As I mentioned in my note (and Avi alluded in his), the IBM Microdrive came with a PCMCIA Type II adapter (labeled IBM) as part of a "kit". I don't know if the CF II spec means all the adapters are the same (or not). What's surprising is that Sandisk doesn't offer an adapter for its own CD II card. I can't find a place where the IBM adapter is sold separately (assuming it even fits a Sandisk). - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 10:54:24 -0700 Reply-To: D&A Software/Avi Sender: HPLX Mailing List From: D&A Software/Avi Subject: D&A Software Website Moved! MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Folks, This is to let you know that the website has been moved to a new hosting site where we home to continue operating. The new hosting organization has hosted a number of domains that I was involved with and while we had a few minor glitches, my opinion is that the service is certainly a good value. If all went as I planned it, you should experience no changes whatsoever. I left the old site in tact and so both locations are mirrors of each other. (you know what they say about plans... :-> ...) If you encounter any difficulties accessing our site, please let me know right away. Thank you! Avi Meshar D&A Software http://www.dasoft.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 13:08:52 -0500 Reply-To: Barry Sender: HPLX Mailing List From: Barry Subject: Re: Compact Flash Too Thick MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit > This is my first posting to this group. Hope it works > I could sure use your help. I just bought a Sandisk > 160MB CF memory card from Ebay to use in my HP100LX. > I also bought a PC Card Adapter from another party. > When I received both, I realized that the card would > not fit into the adapter. It is too thick! I am hoping > that the CF card seller can help me find a suitable resolution. > > However, what I am hoping this group can help me with > is how to read the specifications and know that what I am > ordering will work on the HPLX. I have a Sandisk 160 meg compact flash that I bought from someone on this list. When I got it I didn't have a spare adapter so I used the one I'd been using for my 40 meg compact flash. That adapter is a Sandisk also and is a few years old. I'm not quite sure how long I've had it. In any case it worked just fine in my 200lx. I ordered a new Sandisk adapter, not concerned with thickness since I wasn't aware that this could be an issue and it works just fine too. I don't really use it in the 200lx. 40 meg is plenty for me. I use it to transfer files from my laptop to my desktop. It works fine in the laptop, too. I also just tried it in my 100lx and it worked fine. The numbers on the back are SDCFB and then copyright 99 Sandisk. I'm not sure if the SDCFB is actually a model number but I know they used to put the model numbers on their flash cards. So if yours has the same numbers, I'd get a Sandisk adapter. If not I think I'd call Sandisk and ask them. Or maybe check their website. I think I do remember seeing somewhere that there are two types of compact flash 160 meg cards from Sandisk. I have no idea what the differences are but I guess it's possible you might have just found out. Barry Barry ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 13:48:09 -0500 Reply-To: Barry Sender: HPLX Mailing List From: Barry Subject: Re: Compact Flash Too Thick MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit > I also bought a PC Card Adapter from another party. > When I received both, I realized that the card would > not fit into the adapter. It is too thick! I just did a little looking around on the Sandisk site and it seems that there is a regular compact flash that is 3.3 mm thick and a type II compact flash that is 5.0 mm thick. It also lists the adapater as 5.0 mm thick. The 160 meg card does come in both types. The model number for the regular one is SDCFBX-YY-ZZZ and the model number for the type II is SDCF2BX-YY-ZZZ. The model number for the adapter is SDCF-03. That seems to be their only adapter. Mines just says SDCFB. If yours says SDCF2B it's probably the type II. I can't really find an indication that the adapter will fit the type II. Looking at my adapter it doesnt look like a card half again as thick would fit. I found the reference I remembered to 2 different 160 meg Sandisk compact flash cards at www.cdw.com. But they both have the SDCFB model numbers. They're priced $20 apart and one is in stock and the other one says it takes 2 to 4 weeks to get. There's no mention of any difference in them. I also went through all the Sandisk literature I can find on their site. They used to be full of information and it was easy to find. Now they've made it user friendly and I can't find a thing about the type II compact flash card except that one mention in some downloaded PDF literature. I have a feeling it's probably an OEM product and information on that is only available to registered OEMs. I'm starting to think you might be out of luck trying to use that in the palmtop but I sure don't know that. I think I'd give Sandisk a call. If they say it won't work I think I'd find out what it will work in and see if you can manage a trade. Barry ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 13:53:44 -0500 Reply-To: Barry Sender: HPLX Mailing List From: Barry Subject: Re: Compact Flash Too Thick MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit > Thanks for the welcome news. I start looking around > for a Type II adapter. The normal adapter is a type II adapter since it adapts compact flash to fit in a type II PCMCIA slot. So you'll have to be careful how you ask for what you need. Barry ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 15:17:38 -0400 Reply-To: Mike Schneider Sender: HPLX Mailing List From: Mike Schneider Subject: Re: Compact Flash Too Thick Comments: To: Barry In-Reply-To: <002501c12ff2$c3968fe0$72fe36d8@oemcomputer> MIME-Version: 1.0 Content-Type: text/plain; charset="Windows-1252" Content-Transfer-Encoding: 7bit I missed most of this conversation, but I think what you are looking for is a type II compact flash adapter... Here is one that I bought... http://www.microtechint.com/qs-cfIIadp.html Mike... -----Original Message----- From: HPLX Mailing List Ýmailto:HPLX-L@UConnVM.UConn.Edu¨On Behalf Of Barry Sent: Tuesday, August 28, 2001 2:54 PM To: HPLX-L@UConnVM.UConn.Edu Subject: Re: Compact Flash Too Thick > Thanks for the welcome news. I start looking around > for a Type II adapter. The normal adapter is a type II adapter since it adapts compact flash to fit in a type II PCMCIA slot. So you'll have to be careful how you ask for what you need. Barry ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 07:55:57 +0200 Reply-To: =?iso-8859-1?Q?Jos=E9?= Manuel Armada Sender: HPLX Mailing List From: =?iso-8859-1?Q?Jos=E9?= Manuel Armada Organization: Mi Kasa Subject: Re: HPLX-L Digest - 26 Aug 2001 to 27 Aug 2001 (#2001-264) MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit > Have an hp680 and an hp545, they provide no > help in this respect. Do yourself a favor, > don't get a CE device. Upgrade your 200lx, > you'll be happier in the long run. > Hello - Ken, I will not. I just was curious that, if I ever have to migrate, HP might be the best option because of the migration tools. Thanks for your help. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 15:21:23 -0400 Reply-To: "M. Lennartz" Sender: HPLX Mailing List From: "M. Lennartz" Subject: Re: Compact Flash Too Thick MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > I use it to transfer files from my laptop to my > desktop. It works fine in the laptop, too. I also just tried > it in my 100lx and it worked fine. Hi Barry, I have a laptop MITAC 5033 (Fujitsu...;-) with Win98. The PCMCIA-slot works fine with several cards (network, modem, SRAM), but _not_ with CF (it is 8 MB HP with a noname-adapter). CF plus adapter works well with my 200LX and another laptop with Win2000, so it is ok. How did you get your laptop to work with the CF - or what OS do you use? TIA Mit freundlichem Gru=DF / Regards / Saluton Michael Lennartz lennartz-mi@gmx.net ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 15:36:21 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: Re: Print MM-screen? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Thanks Guenther, did you try that with mm/lx? It does work on my normal screen e.g. file manager. But it doesn't on mm/lx-screens? What might I do wrong? Are there alternatives? Uli ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 21:42:22 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Compact Flash Too Thick MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi On Mon, 27 Aug 2001 15:27:41 -0700, Longden Loo wrote: > My IBM Microdrive is CF Type II and it came with said special PCMCIA > adapter which fits in the 200LX slot. Both card and adapter are the same > thickness. That'S correct, but don't be mislead: It fits mechanically, but none of the Microdrive works in the 200LX, because they need too much power. One of the newer drives can be read, according to tests of Avi Meshar, but not written. End even read only while the palmtop is on AC, IIRC. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 21:42:23 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: A slow lighter system MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Patrick On Tue, 28 Aug 2001 00:37:53 +0000, Stefan Peichl wrote: > Visit a site with photos like Daniel Hertrich's or David > Sergeant's site with their very good explanations. http://www.daniel-hertrich.de/repair There is also a link to David's site. My page doesn't show this connector. But david's does: The pictures "parts3.jpg" shows the connection (item "4") and picture "cable1.jpg" shows the cable with the little hole. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 21:42:24 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: GDB garbage, was Re: new "areacode.gdb" for SUPER MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Nat, On Tue, 28 Aug 2001 05:42:44 +0200, Nathalie Bugeaud wrote: > i am not sure if it is loaded or not; the instructions say to put fastdb.tsr > into C:\_dat, but my autoexec.bat does not have this directory in its path It is loaded. Any *.tsr in the C:\_dat (or a:\_dat, if you "boot" from A:) is loaded automatically when it can be used. > closing the GDB application doesn't reduce the file's size at all - it > actually increases it each time That sounds like a typical effect of fastdb. Delete fastdb.tsr or rename it, reboot the palmtop. And then open the database and close it again. I think this will reduce the file size again? GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 14:48:06 -0500 Reply-To: Chris Lott Sender: HPLX Mailing List From: Chris Lott Subject: Re: Compact Flash Too Thick Comments: To: daniel.hertrich@GMX.DE In-Reply-To: from "Daniel Hertrich" at Aug 28, 2001 09:42:22 PM MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit > > My IBM Microdrive is CF Type II and it came with said special PCMCIA > > adapter which fits in the 200LX slot. Both card and adapter are the same > > thickness. > > That'S correct, but don't be mislead: It fits mechanically, but none of > the Microdrive works in the 200LX, because they need too much power. Might be possible with doubleslot, with the external power supply. -Chris -- ************************************************************************ R. Christopher Lott, P.E. rclott@ro.com Alpha Beta Technologies, Inc. 3112 12th Ave S.W. PHONE: 256-534-9067 Huntsville, Alabama 35805 FAX: 256-534-9069 ************************************************************************ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 22:13:07 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: Print MM-screen? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Ulrich, > Thanks Guenther, > did you try that with mm/lx? > It does work on my normal screen e.g. file manager. I will send you an example from my screen. It works flaless. Kind regards Helmuth ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 16:14:20 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: Accurite Technologies DoubleSlot & Travel Floppy for sale, was Compact Flash Too Thick In-Reply-To: <200108281948.f7SJm6I18525@mail.hiwaay.net> > Might be possible with doubleslot, with the external power supply. It just so happens that I have a DoubleSlot and a Travel Floppy for sale. Accurite currently is selling the DoubleSlot for $149.00 + S&H, and the Travel Floppy for $259.00 + S&H. I am willing to sell the DoubleSlot for $60.00 and the Travel Floppy for $100.00. Both work very well in the 200LX's, and both are in excellent condition. I also have three 200LX's that I am not using. They are a 200LX-2 meg, a 200LX-8 meg double speed, and a brand new 200LX-4 meg. I have intentions on putting the three 200LX's on ebay (which a closed item search shows them selling for around $300.00), but if anyone in interested in buying any of these, or wants the DoubleSlot or Travel Floppy, please email me privately. Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 13:15:47 -0700 Reply-To: patrick@west.net Sender: HPLX Mailing List From: Patrick West Subject: Re: A slow lighter system Mime-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable Folks, Thanks for all the info and support on the swaping of my 200lx= into the 100lx body. I am going to give it a try this weekend. On Tue, 28 Aug 2001 21:42:23 +0200, Daniel Hertrich wrote: >Hi Patrick > >On Tue, 28 Aug 2001 00:37:53 +0000, Stefan Peichl= ONLINE.DE>=A0wrote: > >>=A0Visit a site with photos like Daniel Hertrich's or David >>Sergeant's site with their very good explanations. > >http://www.daniel-hertrich.de/repair > >There is also a link to David's site. >My page doesn't show this connector. But david's does: The= pictures >"parts3.jpg" shows the connection (item "4") and picture >"cable1.jpg" shows the cable with the little hole. > >GTX daniel > >-- >http://www.daniel-hertrich.de/contact > >** HPLX-L LIST Info at= http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- Patrick West, francis_patrick_west@yahoo.com on 08/28/2001 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 21:02:45 -0000 Reply-To: vmbeazel@SWCP.COM Sender: HPLX Mailing List From: Victor Beazel Subject: Re: Compact Flash Too Thick In-Reply-To: Thank you all for your help. The MicroTech site was a good link. I also found another one that was a few bucks cheaper: http://www.progressiveteam.com/product_info.php?products_id=41 This group is a wealth of information. Victor ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 11:03:07 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: ROBOWEB/LX error message MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Wed, 29 Aug 2001 10:38:25 +1200 (NZT) 07h23m44s ago ... On Tue, 28 Aug 2001 17:14:41 +0200, Josef Meyer wrote: > ROBOT/LX Error: > Cannot have RControl=1 and no Post= in ÝHTTP¨ > (Line 15 in file SCR\RWEBINIT.SCR) This should only happen if "ROBOT.EXE -p" is used but the parameter after RWEB1 is not "po" - for example, ExtProg=ROBOT.EXE -p "RWEB1 pp" would cause that error. But then, there should be an immediate exit. > But at the end I found in my Inbox the requested wheather > forecast! I don't know how that happened. Do you just have the one ROBOT.EXE call in your ExtProg=? - Tony ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 23:35:53 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Re: LX <--> Palm via IR Comments: To: Tim MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Tim" > Anyone having any luck beaming documents, files, etc. between a PalmOS > device and a 200LX (or any LX for that matter)? I have been able to do it with IR.EXE and a Palm program called IrPad. This is ok for the occasional Memo or two, but it is very inconvenient for substantial amounts of information. > I tried some of the "Super" downloads, some time ago.... One had some > command/features like "oput" and "oget" I think, but didn't have any luck. That's IR.EXE. It works, but not consistenly (is not bad programming, but it is very difficult to implement the IR protocol to talk to a Palm (is not just IRDA, is more complicated than that). Plus, I read some posts about problems with the physical characteristics of the IR port on the hplx. Something about signal interference (it was related to cell phones with IR functionality, I think). > Any help would be appreciated.... This is not the most helpful post that could be posted, but I am not a technical writer. :-) Anyone who wishes can chip in. > Also, if I can beam, can I CONVERT say, a .WK1 spreadsheet into something > the Palm can use (or vice-versa)? If you can forget about the IR thing, there are lots of options. Palmgear.com has a number of programs which allow you to connect a Palm to a PC via a regular terminal program, which means the same can be done with the hplx. I have not tried this because I have no interest in accomplishing this with cables. I know I would not do it on the go, and at home or work it is much easier to use a Windows system and the hotsync program the Palm comes with. There are several programs which will allow you to share spreadsheet between a PC and a Palm. Check Palmgear. On the hplx, the only options at this time are MakeDoc.exe and DocRead.exe, both found at SUPER. They allow to convert and read text data, respectively. By the way, the Hotsync program is the magic of a Palm. It accomplishes the data translations needed. Without it you are up a creek, only being able to send some text data back and forth. Now, several Windows programs exist which allow to download files to a Palm without Hotsyncing, but this assumes the files are already Palm files, and that the files are NOT for the built in applications, but for third party ones. I have seen a number of different tricks accomplished via the HotSync cradle. But your options are more limited via IR. I hope this meager information helps some. Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 23:38:32 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Re: palm connectivity Comments: To: Scott Barrett MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit ----- Original Message ----- From: "Scott Barrett" > I looked through the list archives and could not find anything like > this, but I thought I would ask... Is there a utility that would let an > HP200 send and recieve the beam signals that the palms use? IR.EXE by Andreas Garzotto, and some of his other programs, such as WWW/LX, are the only thing which would remotely qualify. They are not perfect by far, but no one else has tried, apparently. > I guess I > am looking at a way to transmit and recieve the phone book and > appointment book items. If you can deal with cables, this can be done via Curtis Cameron's hplx to outlook converter, plus some Outlook to Palm converter (there are several on the market). Hal of Thadeus computing tried to find a third party solution to do it via IR (the product was called Synctalk or something), but the folks at Synctalk decided that the hplx is a dead platform, not worth their attention (they already support just about every other handheld in the market, including the now floundering Symbian devices; is not like it would have killed them or something). > I have not programmed these units, but it seems > like it could be a TSR triggered by a keystroke, maybe if you want to > send, just highlight the appt or phone book person and hit ctrl-S, > recieve could work similar. I could see am issue with data translation, > but from looking at friends palms, many fields are very similar and just > need to be pointed in the right direction. Data translation IS the main problem. In overly simplistic and brief terms, an hplx has much more in common with a Mac than with a Palm. For example there are no directories, and no files in the usual sense (it is Palm's idea to spare you the details). You get the idea . . . (for those who may feel this explanation is inadecuate, you are welcome to be more specific; I am kind of tired right now, but just wanted to respond to this post). > Does this exist or is this a new idea. It sure would bring 200 users > into a broader capability. Not new. If you are a programmer and feel inclined to, you can jump into the fray of figuring out the programming issues. But let me tell you that our best hplx programmers have given up on the issue. Even the people at the (former) Palmtop paper tried their hands at this issue. So far no luck. I will comment some more on my response to the other post like yours. Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Tue, 28 Aug 2001 20:40:40 -0700 Reply-To: Ian Butler Sender: HPLX Mailing List From: Ian Butler Subject: Re: David who runs the SUPER site Comments: To: David Becher In-Reply-To: <200107280859.PNR01146@netmedia.net.il> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Tue, 28 Aug 2001, David Becher wrote: > Quite a while ago I sent some software to SUPER and it was not added > to the site, and when I wrote to Mitch to ask, he said that it was > very difficult for him to add software as he no longer has an HPLX > computer. Is there now someone who IS accepting and handling software > updates for SUPER? Yes, send software to super@palmtop.net. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 08:27:57 +0100 Reply-To: HP Staber Sender: HPLX Mailing List From: HP Staber Subject: Re: ROBOWEB/LX error message MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Josef, > ROBOT/LX Error: > Cannot have RControl=3D1 and no Post=3D in ÝHTTP¨ > (Line 15 in file SCR\RWEBINIT.SCR) You should have the following lines in robot.cfg : ÝHTTP¨ PostCfg=3Dc:\w3\post.cfg Post=3Dc:\mail\ indicating in which directory post.cfg sits and which directory receives the downloaded messages (do put the trailing backslash at the end of the second line). HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 04:37:15 -0400 Reply-To: nxw988e@TNINET.SE Sender: HPLX Mailing List From: Lars Hedstroem Subject: Re: A slow lighter system MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Patrick West wrote: > My doublespeed 5meg 200lx has a dying screen. The right half > starts bluring and shifting and even showing stuff from the left > half. If I give it a slight wack to the back of the lid it will > work normally for a few minutes. > > My backup machine is a 1 meg 100lx. -I have been switching stuff > and keep running in to with the way I'm used to doing things. > > > So I find my self using HDM in DOS but then the appointment book > is closed and doesn't beep. -So any ideas? -Is there something I > can use on a 100lx like MaxDOS? - > > Or tips on getting maxDOS to work? - Why not change screens? Reportedly, the screen of a 100LX is the same as a screen of a 200LX. Lars ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 20:46:18 +1200 Reply-To: Tony Hutchins Sender: HPLX Mailing List From: Tony Hutchins Subject: Re: ROBOWEB/LX error message MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Wed, 29 Aug 2001 20:41:21 +1200 (NZT) HP, yup your suggestion would have stopped that error message. Josef was trying the setup in README.TXT which uses only POST.CFG , but he had two extra lines in his "ExtProg" .BAT file which tried to use ROBOT.CFG, but ROBOT.CFG wasn't ready to be used. I have now tried to make the README.TXT a little clearer. - Tony 01h13m24s ago ... On Wed, 29 Aug 2001 08:27:57 +0100, HP Staber wrote: > Josef, > > > ROBOT/LX Error: > > Cannot have RControl=1 and no Post= in ÝHTTP¨ > > (Line 15 in file SCR\RWEBINIT.SCR) > > You should have the following lines in robot.cfg : > > ÝHTTP¨ > PostCfg=c:\w3\post.cfg > Post=c:\mail\ > > indicating in which directory post.cfg sits and which directory > receives the downloaded messages (do put the trailing backslash at the > end of the second line). > > HP Staber/Salzburg > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 01:44:52 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Print MM-screen? Comments: To: Ulrich Allen MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Ulrich Allen wrote: > Is there a way to print the screen of mm/lx? Only two ways to do it: Export to HTML and print the HTML version, or use image grabbing software such as GRABBER to copy the screen. But all you'll get of course is the one screen. I am not sure if you can pan around and "snap pictures" then print them all and tile them together... Maybe possible, but sounds like a lot of work. If you have an idea, please post it. Avi ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 01:45:00 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Print MM-screen? Comments: To: Ulrich Allen MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Ulrich Allen wrote: > Thanks Guenther, > did you try that with mm/lx? > It does work on my normal screen e.g. file manager. > But it doesn't on mm/lx-screens? Look at the MM/LX webpages at http://www.dasoft.com. The first one in the main MM/LX page is an image map to many other maps. All these images were taken with Grabber 3.98. > What might I do wrong? Maybe wrong product? > Are there alternatives? Try Grabber 3.98 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 01:44:56 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Compact Flash Too Thick Comments: To: Victor Beazel MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Victor Beazel wrote: > Avi Meshar said: > > > CF Type II should fit fine in the 200LX. I used a IBM > > Microdrive 1GB which is a Type II CF and it fits fine with its > > adapter. > > I just talked to SanDisk about an adapter for a Type II CF, and they = said > that they have not come out with one yet. Lazy dorks! > Those of you who are using Type II > CF in the 200LX, where did you find your PC Card Adapter? It came with the IBM Microdrive. BTW, someone asked me about the Microdrive. If I recall the questions: Power: Yes uses a lot and REQUIRES P/T on adapter, and even then it gets hot. Also, on prolonged writes, the PCMCIA slot just isn't providing sufficient power and some (long) writes fail. Speed: This failure (see above) manifests either in a total failure to write and the palmtop tells you so, or the write takes an inordinate amount of time, rewriting, rewriting, and on and on to compensate fr errors. Lastly the writer wrote something enthusiastic about the drive. Well, I like it in my notebook and my PC110 and even on the desktop, but the usage on the Palmtop was not planned and only performed to see if it works. So it nominally works, but it is lousy, full of error, and sloooooow. Definitely not intended for the PCMCIA slot of the Palmtop. If you have a separately powered PCMCIA slot for the palmtop it will probably work much much better. Avi ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 01:45:03 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Compact Flash Too Thick Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Daniel Hertrich wrote: > Hi > > On Mon, 27 Aug 2001 15:27:41 -0700, Longden Loo = wrote: > > > My IBM Microdrive is CF Type II and it came with said special PCMCIA > > adapter which fits in the 200LX slot. Both card and adapter are the = same > > thickness. > > That'S correct, but don't be mislead: It fits mechanically, but none of > the Microdrive works in the 200LX, because they need too much power. They need just a litle bit more than the PCMCIA slot can provide, but not much more, so in a marginal way they work. But I would NEVER recommend it, nor rely on it. It also overheats the machine too much, sucking out of it more power than it can provide. Too much damage to the Palmtop in any extended use. I used it max 30 minutes or so. > One of the newer drives can be read, according to tests of Avi Meshar, > but not written. End even read only while the palmtop is on AC, IIRC. Not so. It reads fine, the power is ok for that, although high. But the write is problematic, going OVER the 150mAh of the PCMCIA chassis. I never tried the read with out adapter. I described the writing problems in another post to Victor here. Avi ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 08:33:53 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: DoubleSlot & Travel Floppy sold In-Reply-To: <200108290845.BAA12445@ftel.net> The DoubleSlot and Travel floppy that I was selling has been sold. Thank you all that replied, the response was overwhelming. FYI. Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 09:16:02 -0400 Reply-To: Steve Sender: HPLX Mailing List From: Steve Subject: Re: palmtopping the next generation Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Nathalie wrote: > in my series of intelligent brain implants, an intermediate step has been > achieved. Human Interface Technology of the U of WA are making RSDs > (retinal scanning displays) to draw an image directly on to the retina of > the eye by a low-powered laser scanning back and forth. Because the laser > moves so rapidly, the human visual system sees a complete and stable image. There is a mention of an eye scanning laser imageing system called "Nomad" in the latest issue of "Scientific American". Says it will cost about 8 - 10 thousand dollars this fall though. The article is at http://www.sciam.com/2001/0901issue/0901scicit6.html . Steve ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 08:33:54 -0500 Reply-To: Chris Lott Sender: HPLX Mailing List From: Chris Lott Subject: Re: palmtopping the next generation Comments: To: novosad@SERVER030.FWB.SAIC.COM In-Reply-To: <3.0.6.16.20010829081630.1b5faf06@Server030.FWB.SAIC.Com> from "Steve" at Aug 29, 2001 09:16:02 AM MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit > > achieved. Human Interface Technology of the U of WA are making RSDs > > (retinal scanning displays) to draw an image directly on to the retina of > > the eye by a low-powered laser scanning back and forth. Because the laser > > moves so rapidly, the human visual system sees a complete and stable image. > > There is a mention of an eye scanning laser imageing system > called "Nomad" in the latest issue of "Scientific American". > Says it will cost about 8 - 10 thousand dollars this fall though. Late last fall, we were working on-site at a client's place doing some checkout of a portable data collection box we built them. One aspect of this box was that it recorded, amongst other things, a standard video signal on a little Sony 8mm VCR. Since this box was portable, they had a set of "eyeglasses" sold by Sony that let them view the video signal without needing a cumbersome monitor. They "glasses" they had were reportedly $1K-$2K each, and had a flip-up mirror arrangement that let you view the picture completely in the dark, or alternatively as a heads-up image while you were also looking out in the "real world". That was absolutely neat! Unfortunately for the computer geeks, this particular model only supported ordinary NTSC video, and corresponding units that had VGA or better resolution were many times more expensive. This is getting waay off topic, better quit now. -Chris -- ************************************************************************ R. Christopher Lott, P.E. rclott@ro.com Alpha Beta Technologies, Inc. 3112 12th Ave S.W. PHONE: 256-534-9067 Huntsville, Alabama 35805 FAX: 256-534-9069 ************************************************************************ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 15:23:26 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: Re: Print MM-screen? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable You are Helmuth, it works fine as long as I don't start mm/lx with xf. But that doesn't matter because I know a way now to get my prints. Thanks again. Uli ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 22:06:17 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: Backup with automated dbcheck and alert MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, I have now set up my nightly backup the way Avi suggested, and it works!! Thank you! I have even figured out a second way for the notification in the morning, if the backup was successful or not. See below. I'll now shortly summarize the way: Appointment book invokes a system macro at 2am which closes all applications, then it invokes a bath file backup.bat. Backup.bat does the following: tests, if the battery is good enough for a backup (voltchck), if not, no backup is done and "backup failed: battery" is written into a:\backup_c\report.txt. Then the main DBs are checked by dbcheck. If that fails, no backup is done, anf "backup failed: dbcheck. See a:\dbcheck.log" is written into a:\backup_c\report.txt. The pkzip zips the whole C drive to A:\backup_c If that fails due to disk space shortage (errorlevel 14 of pkzip), "backup failed: disk space" is written into a:\backup_c\report.txt. If pkzip has finished wothout error, "backup succeeded" iss written into the report.txt. Half an hour later (could also be 5 minutes), a second system macro is invoked, which * opens report.txt in Memo * Kopies the content to the clipboard * starte the appointment book * creates a new appointment and fills the fields with: title: clipboard content ("backup failed: xxxxx" or "backup succeeded") time: 8am and so on. This way I get an entry in the appointment book at 8am which says if my backup succeeded or not, and if not, why not. Another way for the notification would be the daily greeting of the appointment book: If you don't need the nice tips appearing each morning, one could write a little program which writes the text, which is now written to report.txt directly into the c:\_dat\appts.ini into the section ÝFORTUNECOOKIES¨. COUNT would have be set to "1", and thus the daily greeting should always show the one "fortune cookie" which contains the backup report. Thanks to Avi for the idea with the appointment entry! GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 22:06:25 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: SECDEV questions MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, I'm considering to install secure device on my palmtop, instead of my current PGP setup to encrypt a file with personal data. From what I have seen so far, a big disadvantage of secdev compared to PGP seems to be that I MUST have a device driver loaded all the time, even when I don't use secdev. Is that correct? If yes, how much conventional memory does it take up? I run out of memory in some of my Souftware Carousel work areas, so this could be a real problem. Or is it possible to load this device driver in only one SC area via it's own "autoexec.bat" and with the device driver loader supplied with SC? How long does it take to decrypt data? In my PGP setup I use a 768 bit key, which needs about 15 sec to decrypt a text file which is 5 kB in size. Is Secdev faster? Thanks for answers! daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 23:04:33 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: SECDEV questions Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Daniel Hertrich wrote: > I'm considering to install secure device on my palmtop, instead of my > current PGP setup to encrypt a file with personal data. SecDev is Good stuff! > From what I have seen so far, a big disadvantage of secdev compared to > PGP seems to be that I MUST have a device driver loaded all the > time, even when I don't use secdev. Is that correct? > If yes, how much conventional memory does it take up? I don't think it is a BIG disadvantage. I ran MEM both with the driver loaded and also after I rebooted without it. As you can see below, it uses about 6k of storage. If you know you don't need access to your SecDrv drive you can comment out the driver in your Config.Sys file and recover that 6k but it isn't worth it (to me). Note, I also run with SC v7 loaded which partly explains the 560k free storage. ------------------------------------------- With SECDEV.SYS driver loaded 651264 bytes total conventional memory 651264 bytes available to MS-DOS >> 560288 largest executable program size 4194304 bytes total EMS memory 0 bytes free EMS memory ------------------------------------------- Without driver loaded 651264 bytes total conventional memory 651264 bytes available to MS-DOS >> 566832 largest executable program size 4194304 bytes total EMS memory 0 bytes free EMS memory ------------------------------------------- > I run out of memory in some of my Souftware Carousel work areas, so > this could be a real problem. > Or is it possible to load this device driver in only one SC area via > it's own "autoexec.bat" and with the device driver loader supplied with > SC? No, it loads via Config.Sys so it uses memory that is common to all work areas. > How long does it take to decrypt data? > In my PGP setup I use a 768 bit key, which needs about 15 sec to > decrypt a text file which is 5 kB in size. Is Secdev faster? It doesn't encrypt 'FILES', it encrypts/decrypts disk sectors as DOS write and reads them. In general I don't notice any delay on my 1x speed LX but I also only have a 64k SecDev drive with a couple small files on it. They're so small (several K max) that the extra overhead is do slight I don't notice any delays. If you create a 4Meg drive and start using files of several hundred K then you'd start noticing extended read/write times. Probably less noticable impact on a 2x LX. Give it a try; it's easy to setup and just as easy to remove if you don't like it. Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 21:52:27 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: 200LX to WinCE tools MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > Does HP still provide migration tools for the > HP200LX built-in apps. when you purchase one of > their WinCE machines?. I recently got a Jornada 690. It came with a program to move my 200LX appointment book and phone book to the Jornada. It only works one-way, however. You can't synchronize them after the initial "dump" into the = Jornada. Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 21:52:31 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: OL2LX 3.03: converting phone book limits? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > Is there a limit in the number of phone book records converted from the > HPLX to Outlook by Curtis Cameron's OL2LX 3.03? I got it to convert my phonebook with 302 entries. So, it is possible to = do that many. Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 21:52:35 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: GDB garbage MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > any way out? Try adding an empty record to the database then deleting it. Now close = the database and check the size. If this doesn't work, reopen and add two = empty records and then delete them before closing the database. Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 21:52:39 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: maximum NiCd voltage MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > BTW, my rechargable NiCd batteries can not be charged to 3.09v to which = I > set in the ABC, but only to 2.8v then drop. This is normal for NiCd batteries. They don't have as high a maximum = voltage as Alkaline and Lithium batteries do. NiMH rechargeable batteries also = have a lower maximum voltage, a lot like the NiCd Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 22:42:35 -0400 Reply-To: KenLondon Sender: HPLX Mailing List From: KenLondon Subject: Re: 200LX to WinCE tools MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Steve Carder wrote: > I recently got a Jornada 690. It came with a program to move my 200LX > appointment book and phone book to the Jornada. It only works one-way, > however. You can't synchronize them after the initial "dump" into the Jornada. What program is that? Got a 680 and a 545, neither had such a program. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 19:49:07 -0700 Reply-To: Ian Butler Sender: HPLX Mailing List From: Ian Butler Subject: Re: 200LX to WinCE tools In-Reply-To: <3B8DA81B.B9F45BA1@beld.net> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Wed, 29 Aug 2001, KenLondon wrote: > Steve Carder wrote: > > > I recently got a Jornada 690. It came with a program to move my 200LX > > appointment book and phone book to the Jornada. It only works one-way, > > however. You can't synchronize them after the initial "dump" into the Jornada. > > What program is that? Got a 680 and a 545, neither had such a program. Um, assuming you're talking about the Jornada 680, it does indeed come with such a program. And it works quite well, although I prefer the 200LX's phone book and appointment book to the ones on the Jornada. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 05:36:18 +0100 Reply-To: HP Staber Sender: HPLX Mailing List From: HP Staber Subject: Fwd: FS: HP-200LX MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable --- begin of forwarded message --- From: "Wolf Video" Subject: FS: HP-200LX Date: Wed, 29 Aug 2001 20:20:58 GMT $200.00 Excellent condition with AC adaptor& manual. Also a 1 meg PCMCIA card. -- WOLF VIDEO (818) 905-WOLF (9653) Production * Digital Editing * Graphics * Internet =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D Contact: Ralph McCarron web: http://www.wolfvideo.net email: support@wolfvideo.net --- end of forwarded message --- HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 05:14:30 +0200 Reply-To: Nathalie Bugeaud Sender: HPLX Mailing List From: Nathalie Bugeaud Subject: Subject: Re: MM/LX display bug MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Helmuth and Curtis asked: "Did this all happen using version 1.1a?" Yes, all that starting my first file even ! :) > After a few losses of links due to entering note text (and getting warned: > ERROR - Invalid Link #.....) and after creating 2 files within the same > file, the second file showing garbled text in place of a child, .. to be exact, i herewith correct my "garbled text" as actually being the "overlap" as explained below: >Using the latest mm.exe with meeting.mm from Helmuths example >map there is a problem displaying the items in the first >meeting. Zooming displays correctly, but in regular mode the >items overlap. If I delete either of the children from the Todos >entry it displays correctly. Adding a second Todos child to the >second meeting causes this one to overlap also. and.. >I saw this as well with my own map. One of the children of the main >item was on the left side, but its children displayed to the right, >interfering with the main item and its children which were displayed >on the right side. is it possible that you have re-named the central item making it longer? The arrows/lines do not seem to follow the longer text in the main item if altered. another lesson i had to learn: even if PE is in the same directory as MM and identified as EDITOR=PE.EXE, MM/LX cannot find it if the full path is not specified; this also applies to the starting menu file. so, mine looks like: Editor=C:\pe\LW.EXE Start=C:\pe\MENU.MM LW is LapWrite in giant font (fat letters on only 11 lines per screen - good for dimly lit phone booths) nat ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 00:07:20 -0400 Reply-To: MCHEM1@UCONNVM.UCONN.EDU Sender: HPLX Mailing List From: Al Kind Subject: LX <--IR-->OB800 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Thu, 30 Aug 2001 00:05:30 -0500 (EST) OK, with all the OB800CT & LX owners out there, has anyone figured out how to exchange files via the IR? TIA & Cheers...AJKind -- * Al Kind, 3113 Horsebarn Rd U-193, Storrs CT 06269-4193 USA * Phone:(860)486-6126 EFax:(413)826-8780 **TeamHP200LX** ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Wed, 29 Aug 2001 21:34:34 -0700 Reply-To: kopplin@TECHNOIR.NU Sender: HPLX Mailing List From: Mike Kopplin Subject: Re: Subject: Re: MM/LX display bug In-Reply-To: <000901c13107$c7ce4240$e320fac1@oemcomputer> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Thu, 30 Aug 2001, Nathalie Bugeaud wrote: > to be exact, i herewith correct my "garbled text" as actually being the > "overlap" as explained below: > > >Using the latest mm.exe with meeting.mm from Helmuths example > >map there is a problem displaying the items in the first > >meeting. Zooming displays correctly, but in regular mode the > >items overlap. If I delete either of the children from the Todos > >entry it displays correctly. Adding a second Todos child to the > >second meeting causes this one to overlap also. > > is it possible that you have re-named the central item making it longer? The > arrows/lines do not seem to follow the longer text in the main item if > altered. Not in my case. To make sure it wasn't a problem with the file, I unzipped the original example map again. Display problem was still there. I have not encountered it so far in my own mapping. Mike ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 00:08:08 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Backup with automated dbcheck and alert Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Daniel Hertrich wrote: > Hi friends, > > I have now set up my nightly backup the way Avi suggested, and it > works!! Thank you! I am glad my idea helped. Your second idea to create an appointment is excellent! I have been asked many times about creating a macro that will produce today's date so it can be used in a back up application to generate the date to include in the file name. Here is an idea which is not complete, but maybe someone will be inspired: In Calculator we have a Date application, accessible by CTRL-D once you are in CALC. F10 enters todays date in a format that depends how you set up your date in the SETUP application / time-date setup. I use yyyy-mm-dd so I'll use that date format. The manipulation I'll describe have to be changed a little to accomodate other date formats... When I press F1 and enter, then press COPY, I get this when I paste it into Memo: "2,001.0829 " (no quotes, but I wanted to show the trailing blank. Press Home, type "SET HEUTE=3D" without the quotes, then del key 3 times to remove the 2, ",", and "0". You are left with SET HEUTE=3D01.0829 Right arrow 3 times, Del once get rid of dot. Jump to end, get rid of trailing space (important!) Menu, Save-As, A:\batch\heute.bat (and if exists, enter F10 to overwrite. So you have a tiny batch file called HEUTE.BAT (in German, for non-German speaking folks, "Heute" means "today"). If you run it, you get an environment item called HEUTE with a value of 010829 (or whatever date it is!) All this is wonderful, but how to use? Well in batch file you can use an environment variable like this: ren a:\backup\cbak.zip a:\backup\c%heute%.zip And now you have ahe zip file called: C010829.ZIP I am sure this gives you a good start to do the rest of the details ... Enjoy. Avi ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 00:08:04 -0700 Reply-To: sponsor@FTEL.NET Sender: HPLX Mailing List From: Avi Meshar Subject: Re: Backup with automated dbcheck and alert Comments: To: Daniel Hertrich MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Daniel Hertrich wrote: > Hi friends, > > I have now set up my nightly backup the way Avi suggested, and it > works!! Thank you! I have even figured out a second way for the > notification in the morning, if the backup was successful or not. See > below. I'll now shortly summarize the way: > > Appointment book invokes a system macro at 2am which closes all > applications, then it invokes a bath file backup.bat. > > Backup.bat does the following: tests, if the battery is good enough for > a backup (voltchck), if not, no backup is done and "backup failed: > battery" is written into a:\backup_c\report.txt. > Then the main DBs are checked by dbcheck. If that fails, no backup is > done, anf "backup failed: dbcheck. See a:\dbcheck.log" is written into > a:\backup_c\report.txt. > The pkzip zips the whole C drive to A:\backup_c > If that fails due to disk space shortage (errorlevel 14 of pkzip), > "backup failed: disk space" is written into a:\backup_c\report.txt. > If pkzip has finished wothout error, "backup succeeded" iss written > into the report.txt. > > Half an hour later (could also be 5 minutes), a second system macro is > invoked, which > * opens report.txt in Memo > * Kopies the content to the clipboard > * starte the appointment book > * creates a new appointment and fills the fields with: > title: clipboard content ("backup failed: xxxxx" or "backup > succeeded") > time: 8am > and so on. > > This way I get an entry in the appointment book at 8am which says if my > backup succeeded or not, and if not, why not. > > Another way for the notification would be the daily greeting of the > appointment book: If you don't need the nice tips appearing each > morning, one could write a little program which writes the text, which > is now written to report.txt directly into the c:\_dat\appts.ini into > the section ÝFORTUNECOOKIES¨. COUNT would have be set to "1", and thus > the daily greeting should always show the one "fortune cookie" which > contains the backup report. > > Thanks to Avi for the idea with the appointment entry! > > GTX > daniel > > -- > http://www.daniel-hertrich.de/contact > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 14:14:18 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: Subject: Re: MM/LX display bug MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Nathalie, Mike, thank you very much for your feedback, in the beta we are analyzing the problem and working on it. Andreas pointed out: In MM/LX version 1.1, one goal was to render the maps on the screen in an even more compact form than in 1.1. By doing that, new situations have been introduced. Look at this example: This is the central item / Child Due to compaction, "Child" starts *right* of the central item even though it is *left* of the item, structurally. This can lead to some odd effects, namely that MM/LX thinks the item is to the right of the central item and thus adds more children to the right. A work around is to make sure the central item text is not longer than the text of its children. In the beta, we are working on a solution to this problem, which will be available in the next release. Kind regards Helmuth > On Thu, 30 Aug 2001, Nathalie Bugeaud wrote: > > to be exact, i herewith correct my "garbled text" as actually being the > > "overlap" as explained below: > > > > >Using the latest mm.exe with meeting.mm from Helmuths example > > >map there is a problem displaying the items in the first > > >meeting. Zooming displays correctly, but in regular mode the > > >items overlap. If I delete either of the children from the Todos > > >entry it displays correctly. Adding a second Todos child to the > > >second meeting causes this one to overlap also. > > > > is it possible that you have re-named the central item making it longer? The > > arrows/lines do not seem to follow the longer text in the main item if > > altered. > > Not in my case. To make sure it wasn't a problem with the file, > I unzipped the original example map again. Display problem was > still there. I have not encountered it so far in my own mapping. > > Mike > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 08:15:43 -0400 Reply-To: Steve Sender: HPLX Mailing List From: Steve Subject: Re: palmtopping the next generation Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Chris Lott wrote: > Since this box was portable, > they had a set of "eyeglasses" sold by Sony that let them view the > video signal without needing a cumbersome monitor. They "glasses" > they had were reportedly $1K-$2K each, and had a flip-up mirror > arrangement that let you view the picture completely in the dark, > or alternatively as a heads-up image while you were also looking > out in the "real world". That was absolutely neat! Unfortunately > for the computer geeks, this particular model only supported ordinary > NTSC video, and corresponding units that had VGA or better resolution > were many times more expensive. I purchased a gadget called "iGlasses" that work with tv video (not tried), and the 320x200 VGA mode. They even had a 3D version of the game "Heretic" that came with it. It had a head tracker built in that let you use your head like a poor joystick. It uses semi-transparent mirrors, so you could get the Heads Up Display effect while you tried to get everything set up. Then one installed a shield to see the images without distraction. > This is getting waay off topic, better > quit now. Aw.. Steve ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 06:09:34 -0700 Reply-To: wayne.yang@bigfoot.com Sender: HPLX Mailing List From: "Wayne E. Yang" Subject: Multilingual Dictionary MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="0-1579752469-999176974=:45026" --0-1579752469-999176974=:45026 Content-Type: text/plain; charset=us-ascii You often see DOS-based dictionaries for sale on Ebay. And don't forget that Thaddeus sells the Collins Multi-Lingual Dictionary: http://www.palmtoppaper.com/cgi-bin/shop.plx/SID=PUT_SID_HERE/page=dictions.htm Wayne E. Yang ============= wayne_yang@yahoo.com --------------------------------- Do You Yahoo!? Get email alerts & NEW webcam video instant messaging with Yahoo! Messenger. --0-1579752469-999176974=:45026 Content-Type: text/html; charset=us-ascii

You often see DOS-based dictionaries for sale on Ebay. And don't forget that Thaddeus sells the Collins Multi-Lingual Dictionary:

http://www.palmtoppaper.com/cgi-bin/shop.plx/SID=PUT_SID_HERE/page=dictions.htm

 



Wayne E. Yang
=============
wayne_yang@yahoo.com


Do You Yahoo!?
Get email alerts & NEW webcam video instant messaging with Yahoo! Messenger. --0-1579752469-999176974=:45026-- ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 16:28:13 +0200 Reply-To: Lasse Karlsson Sender: HPLX Mailing List From: Lasse Karlsson Subject: SMS and Post/PDU with Nokia 6210 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Thu, 30 Aug 2001 16:30:53 +0200 (CET) Hi all, Has anyone managed to send SMS with Post/PDU using a Nokia 6210? I decided to give it a try and had no luck sending directly from Post. Copying messages to/from Post and the SIM-card was no problem. Seems like the phone gives an error msg after the AT+CMGS command ;-( BTW I used a cable connection. Any ideas? Regards Lasse in Stockholm ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 10:10:23 -0500 Reply-To: Hal Goldstein Sender: HPLX Mailing List From: Hal Goldstein Subject: 96 Meg upgrades possibly available? Comments: cc: Wayne Kneeskern MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Hi Everyone, We have an opportunity to purchase 30 96 meg upgrade kits via Mack. (We would probably need to get and sell at least 20.) As you might imagine given your cost, Mack and my costs are also quite substantial. Therefore, I need to have a good idea if there is a demand before we go ahead. If you really think you will want to get an upgrade or a refurbished unit with the upgrade, please email me. Your response isn't binding, but PLEASE don't respond to me unless you are 100% sure you will purchase the upgrade or unit. Prices: Upgrade to 96 meg: From 2 or 4 meg: $999 From 5 or 6 meg: 964 From 8 meg: 934 From 32 meg: 799 From 64 meg: 599 Subject to availability -- currently we have only a few new units in stock if that: Used 200LX with 96 meg: 1225 New 200LX with 96 meg: 1499 Thanks! ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 08:48:49 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: LX <--IR-->OB800 MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > OK, with all the OB800CT & LX owners out there, has anyone figured out > how to exchange files via the IR? They're using incompatible IR protocols (Irda on the 800, HP-SIR on the LX), so IR (using the built-in IR transceivers) isn't possible unless someone writes a driver to make one machine compatible with the other. There are SIR drivers, and I've tried some on the 800CT with no luck. I imagine that at the hardware level, the IR devices for which the SIR drivers were written (some off-shore notebook) differed from the 800's. There may be some combination of Laplink that might work, tho I haven't tested that exhaustively. All in all, it's usually faster and more reliable to swap the ol' PC card and do the transfer that way. But of course, if anyone knows a reliable way to transfer using the IR's, I'd like to know too. - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 23:47:16 +0800 Reply-To: swsabn@yahoo.com Sender: HPLX Mailing List From: Stephen Soper Subject: Receiving the List as a Digest MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit It has been a long time since I've contributed, but I've been receiving the messages in Digest form on my CompuServe account. I want to drop CompuServe, and so I signed up for the list on my Yahoo account - but it comes in all the individual messages. How do I get the messages in the Digest form? Thanks Steve & Witney Soper (and Supaporn, Alexander, Benjamin, and Napoleon) #39 Fengyung New Town; Fengyung Village; Lunpei; Yunlin County; Taiwan ROC-637 886-5-655-1951 -or- 886-912310941 (Hand Phone) stvsoper@ms48.hinet.net, supersoper@compuserve.com, swsabn@yahoo.com _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 23:47:19 +0800 Reply-To: swsabn@yahoo.com Sender: HPLX Mailing List From: Stephen Soper Subject: Converting 123 csf to a dBase File MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit I have a big spreadsheet of addresses for a control system that I'm working on - (about 2,500 rows, by 13 columns - many of the rows are wide because they describe the equipment or model). I want to convert it to the database program so that I can carry it with me, plus the dBase program is better for searching. I tried converting it to a comma separated file from it's native Excel, and then converting it to dBase with the dbio program from super. When I opened the converted file, it said it couldn't find a record. I then tried saving it to Lotus 123, and converting it to a csf via the add-in from Super. But, when I tried to use dbio.exe again, I ended up with the same problem. I think I did everything right for dbio.exe. Does anyone have any suggestions? Thanks Steve _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 12:15:46 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: FS: Palmtop & various other items In-Reply-To: I finally got off my butt and took inventory of what I have for sale. All of these items include standard US shipping. If interested please contact me privately. I thought I would try the list first before listing these on ebay. Any questions please feel free to contact me. Brand new (unused) 200LX 4 meg-1X speed (as shipped from factory) Language: US English Serial Number: SG80500805 Includes: original box & unopened manuals Condition: brand new-never used Price: $300.00 Like new 200LX-2 meg-1X speed (as shipped from factory) Language: US English Serial Number: SG62102250 Includes: original box & manuals Condition: excellent Price: $250.00 (Thaddeus sells for $300) Used 200LX-8 meg-2X speed (Thaddeus upgraded, was 1 meg-1X speed) Language: US English Serial Number: SG53600968 Includes: manuals & carry case Condition: repaired right side hinge crack, otherwise good condition Price: $250.00 (Thaddeus sells for $400) HP AC Adapter Model Number: F1011A-ABA Price: $25 (Thaddeus sells for $50) One Outlet AC Adapter Price: $20 (Thaddeus sells for $40) 2-HP Connectivity Cables Model Number: F1015-80002 Price: $20 each (Thaddeus sells for $40) 2-Belkins Serial to Parallel Adapters Model Number: F5F113 Price: $40 each (Thaddeus sells Greenwich for $70, I paid $90 each for these) Cigarette Lighter Adapter Price: $15 Pocket Quicken Connect Includes: manual & disk Price: $10 PowerBasic v3.50 Includes: PB user guide, PB reference guide, disks & Sam s Learning Basic book Price: $50 (I paid $100 for PB software which is still sold and supported at v3.50 for $100 at: www.powerbasic.com, learning basic book was $40.00) Lotus 123 v2.4 (full version-same version that HP 200LX has on it) Includes: Original box, manuals & disks Price: $40 ABC/LX Advanced Battery Charging software Includes: Manual & disk Price: $15 (Thaddeus sells for $35) Personal Food Analyst Includes: Manual & PCMCIA card with software on card Price: $7 (Thaddeus sells for $12) Pretec 12MB ATA PCMCIA Flash Card Price: $15.00 (you don t want to know what I paid for this) 2-SimpleTech 40MB ATA PCMCIA Flash Card Price: $40 each (you don t want to know what I paid for these) APEX Mobile Plus Cellular V.34 33.6 Data/Fax Modem Includes: Cable to connect modem to landline & cable to connect modem to StarTAC Cellular phone. Works well in 200LX. Price: $40 (I paid $100 for modem & landline cable & $50 for StarTAC cable, which I am including for no additional charge) Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 12:35:27 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: FS: Update on Palmtop & various other items Just an update on the items I have for sale. The 200LX-1 meg is sold, and so is the Pocket Quicken Connect software. First come, first serve, and those two were in minutes! Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 13:09:35 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: FW: Update on Palmtop & various other items Correction to my last update, the 200LX-2 meg is sold, not the 200LX-1 meg. I don't have a 1 meg unit for sale. Also I forgot about another large item. I have 47 issues of the HP Palmtop Paper, dated from January 1993 to August 1999, and the HP 100LX/200LX Developer's Guide (over 572 pages), and 6 Subscriber Power Disks dated from 1993 to 1998. This whole package price is: $90, which includes $30 in shipping charges. All the items weigh 20 pounds. I called my local Mail Boxes, ETC, and they said for me to ship 20 pounds it would cost $30. Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 10:32:04 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: Converting 123 csf to a dBase File MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > I tried converting it to a comma separated file from it's native > Excel, and then converting it to dBase with the dbio program from super. > When I opened the converted file, it said it couldn't find a record. I then > tried saving it to Lotus 123, and converting it to a csf via the add-in from > Super. But, when I tried to use dbio.exe again, I ended up with the same > problem. I think I did everything right for dbio.exe. Does anyone have any > suggestions? I've never tried dbio.exe, but if it works like gdbdump/gdbload (which I have tried), then when you open the newly created DB for the first time (and get the record msg), you have to re-define the subset (F6/All database Items) before anything shows up. - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 13:40:05 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: FS: update on items sold Here is an update on the items I have for sale that have been sold: Pocket Quicken Connect 200LX-2 meg-1X speed Travel Floppy & DoubleSpeed 1-40 meg flash card One Outlet AC Adapter ABC/LX I will keep you up to date on what I have confirmed that is sold. Thanks everyone. Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 11:45:06 -0700 Reply-To: Paulo Custodio Sender: HPLX Mailing List From: Paulo Custodio Subject: Re: SECDEV questions Comments: To: Daniel Hertrich In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii --- Daniel Hertrich wrote: > I'm considering to install secure device on my > palmtop, instead of my > current PGP setup to encrypt a file with personal > data. It's a nice program. > How long does it take to decrypt data? > In my PGP setup I use a 768 bit key, which needs > about 15 sec to > decrypt a text file which is 5 kB in size. Is Secdev > faster? In my setup (double speed 32M HP-LX), it takes about 2 seconds to copy a 5K file to the encrypted drive. Paulo __________________________________________________ Do You Yahoo!? Get email alerts & NEW webcam video instant messaging with Yahoo! Messenger http://im.yahoo.com ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 14:54:09 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: Re: update on items sold In-Reply-To: Here is another update on the items I have for sale that have been sold: Pocket Quicken Connect 200LX-2 meg-1X speed Travel Floppy & DoubleSpeed 1-40 meg flash card One Outlet AC Adapter ABC/LX 1-Belkin's Serial to Parallel Adapter APEX Cellular Modem I will keep you up to date on what I have confirmed that is sold. Thanks everyone. Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 22:05:45 +0200 Reply-To: "Guenther Helmuth E." Sender: HPLX Mailing List From: "Guenther Helmuth E." Subject: Re: SMS and Post/PDU with Nokia 6210 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Lasse, > Hi all, > Has anyone managed to send SMS with Post/PDU using a Nokia 6210? > I decided to give it a try and had no luck sending directly from Post. > Copying messages to/from Post and the SIM-card was no problem. > Seems like the phone gives an error msg after the AT+CMGS command ;-( > BTW I used a cable connection. Try IrDA and it will work. Using the cable connection requires cable XXX. First you might see if it works using Datacom from SYSMGR. Just type AT&F and see if you will get an OK? Good luck! Kind regards Helmuth ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 19:24:14 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: 200LX to WinCE tools MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > What program is that? Got a 680 and a 545, neither had such a program. The CD that came with the Jornada is at the office and I am at home. = When I started the CD, it had a menu option for HP utilities. The conversion = tools were under there. I will try to look for a more specific answer tomorrow. Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 17:25:46 -0600 Reply-To: "Robert K. Meyer" Sender: HPLX Mailing List From: "Robert K. Meyer" Subject: Re: Converting 123 csf to a dBase File Comments: To: swsabn@yahoo.com MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Excel ought to work. Lotus includes a program specifically for DBase/123 conversions in the retail DOS Lotus package. Bob Stephen Soper wrote: > > I have a big spreadsheet of addresses for a control system that I'm working > on - (about 2,500 rows, by 13 columns - many of the rows are wide because > they describe the equipment or model). I want to convert it to the database > program so that I can carry it with me, plus the dBase program is better for > searching. I tried converting it to a comma separated file from it's native > Excel, and then converting it to dBase with the dbio program from super. > When I opened the converted file, it said it couldn't find a record. I then > tried saving it to Lotus 123, and converting it to a csf via the add-in from > Super. But, when I tried to use dbio.exe again, I ended up with the same > problem. I think I did everything right for dbio.exe. Does anyone have any > suggestions? > > Thanks > Steve > > _________________________________________________________ > Do You Yahoo!? > Get your free @yahoo.com address at http://mail.yahoo.com > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY http://w3.union-tel.com/~bmeyer/ The stone... Psa 118:22 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Thu, 30 Aug 2001 20:06:31 -0600 Reply-To: "Robert K. Meyer" Sender: HPLX Mailing List From: "Robert K. Meyer" Subject: Re: FS: update on items sold Comments: To: Robert Hocking MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Man, did not even get a chance to ask you about your stuff, now it is gone. Anyway, I hate to see you LXless. You introduced me to this list some time ago. Unfortunately, you introduced me to the dreaded hinge crack also! Bob Robert Hocking wrote: > > Here is an update on the items I have for sale that have been sold: > > Pocket Quicken Connect > 200LX-2 meg-1X speed > Travel Floppy & DoubleSpeed > 1-40 meg flash card > One Outlet AC Adapter > ABC/LX > > I will keep you up to date on what I have confirmed that is sold. Thanks > everyone. > > Best Regards, > > Robert Hocking > > ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml -- R.K. Meyer MSEE K7PPC bmeyer@union-tel.com Elk Mountain WY http://w3.union-tel.com/~bmeyer/ The stone... Psa 118:22 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 07:17:08 +0100 Reply-To: hpstaber@COMPUSERVE.COM Sender: HPLX Mailing List From: HP Staber Subject: Fwd: FS HP 200lx MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable --- begin of forwarded message --- From: "Lee Sublett" Subject: FS HP 200lx Date: Mon, 27 Aug 2001 19:48:32 -0600 I have a HP200LX w/ 10 meg PC card and All manuals, and connectivity cables/adapaters// Best voffer get it.. Works great...> --- end of forwarded message --- HP Staber/Salzburg ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 01:35:38 EDT Reply-To: AHA2K@AOL.COM Sender: HPLX Mailing List From: AHA2K@AOL.COM Subject: Re: HPLX-L Digest - 26 Aug 2001 to 27 Aug 2001 (#2001-264) MIME-Version: 1.0 Content-Type: text/plain; charset="US-ASCII" Content-Transfer-Encoding: 7bit ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 08:18:24 +0200 Reply-To: Lasse Karlsson Sender: HPLX Mailing List From: Lasse Karlsson Subject: Re: SMS and Post/PDU with Nokia 6210 Comments: To: "Guenther Helmuth E." MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Fri, 31 Aug 2001 08:02:04 +0200 (CET) 09h57m58s ago ... On Thu, 30 Aug 2001 22:04:06 +0200, Guenther Helmuth E. wrote: > > Has anyone managed to send SMS with Post/PDU using a Nokia 6210? > > Try IrDA and it will work. > > Using the cable connection requires cable XXX. Thanks for a quick response. I already use the phone with Post/LX for mail both with cable and Irda. My problem with PDU is that I can copy SMS messages to/from the SIM-card from an SMS-box in Post but I cannot send them directly. The AT+CMGS command gives an error. Regards Lasse ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 08:05:05 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Re: SMS and Post/PDU with Nokia 6210 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi Lasse, On Thu, 30 Aug 2001 16:28:13 +0200, Lasse Karlsson wrote: > Thu, 30 Aug 2001 16:30:53 +0200 (CET) > Hi all, > Has anyone managed to send SMS with Post/PDU using a Nokia 6210? > I decided to give it a try and had no luck sending directly from Post. > Copying messages to/from Post and the SIM-card was no problem. > Seems like the phone gives an error msg after the AT+CMGS command ;-( You have to adjust the SMSC number in sms.tpl. It is the SMS center number, i.e. the number you also set in the telephone as SMS service center. GTX daniel -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 09:00:24 -0400 Reply-To: Steve Sender: HPLX Mailing List From: Steve Subject: Re: LX <--IR-->OB800 Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Longden Loo wrote: > > OK, with all the OB800CT & LX owners out there, has anyone figured out > > how to exchange files via the IR? > They're using incompatible IR protocols (Irda on the 800, HP-SIR on the > LX), so IR (using the built-in IR transceivers) isn't possible unless > someone writes a driver to make one machine compatible with the other. > There are SIR drivers, and I've tried some on the 800CT with no luck. I > imagine that at the hardware level, the IR devices for which the SIR > drivers were written (some off-shore notebook) differed from the 800's. I tried to track down the hardware specifications without much luck. Is there a Linux driver (with source) available? What is the SIR driver you have? Steve ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 15:44:49 +0200 Reply-To: Alan Krempler Sender: HPLX Mailing List From: Alan Krempler Subject: Re: LX <--IR-->OB800 MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit i could try to program such a thing, but it is too hard to write an IrDA stack myself. i asked at D&A software if they would share their code or libraries from IR.EXE, but i got no reply. if someone knows a source to an IrDA stack, please drop me a hint. alan krempler ------ Date: Thu, 30 Aug 2001 00:07:20 -0400 From: Al Kind Subject: LX <--IR-->OB800 Thu, 30 Aug 2001 00:05:30 -0500 (EST) OK, with all the OB800CT & LX owners out there, has anyone figured out how to exchange files via the IR? TIA & Cheers...AJKind ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 09:51:47 -0400 Reply-To: steve@CARDERFAMILY.NET Sender: HPLX Mailing List From: Steve Carder Subject: Re: Converting 123 csf to a dBase File MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable > I have a big spreadsheet of addresses for a control system that I'm = working > on - (about 2,500 rows, by 13 columns - many of the rows are wide = because > they describe the equipment or model). This may be too big for the built-in database program in the LX. You can = use a free database program called Data Perfect on the LX which can handle = databases this large. Data Perfect will import Comma-deliminated files. I use = Data Perfect to track the 1500 or so books in my personal library. Steve Carder PGP public key on the server at http://pgp.mit.edu ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 09:19:56 -0500 Reply-To: Theodore Heise Sender: HPLX Mailing List From: Theodore Heise Subject: Re: Converting 123 csf to a dBase File In-Reply-To: <200108311351.JAA02534@siaar2ab.compuserve.com> MIME-Version: 1.0 Content-Type: TEXT/PLAIN; charset=US-ASCII On Fri, 31 Aug 2001, Steve Carder wrote: > > I have a big spreadsheet of addresses for a control system that I'm working > > on - (about 2,500 rows, by 13 columns - many of the rows are wide because > > they describe the equipment or model). > > This may be too big for the built-in database program in the LX. You can use a > free database program called Data Perfect on the LX which can handle databases > this large. Data Perfect will import Comma-deliminated files. I use Data > Perfect to track the 1500 or so books in my personal library. An easy option (but it would lack the search functionality you desired) would be to save the Excel file as a *.wk1 file and use it in the native Lotus 123. By the way, I believe the request was for a palmtop format database file, but the Subject (...a dBase File) could be confused with another database format. Ted -- Theodore W. Heise West Lafayette, IN, USA ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 14:32:08 +0000 Reply-To: fjkaufman@WORLDNET.ATT.NET Sender: HPLX Mailing List From: "F. Kaufman" Subject: Re: GDB garbage, was Re: new "areacode.gdb" for SUPER Comments: To: Nathalie Bugeaud MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit > Daniel asked: > >Do you use this "fastdb" TSR (or whatever its name is)? I think > >this could cause such problems, because, AFAIK, changes in the GDB > >are not really worked into the GDB, but appended, for > >faster processing, just like the "fast save" option of MS Word works. > > i am not sure if it is loaded or not; the instructions say to put fastdb.tsr > into C:\_dat, but my autoexec.bat does not have this directory in its path That directory does not have to be in the path and the fastdb.tsr does not get executed by the user. But if it is in that path or maybe a:\_dat, the hp recognizes it and will run it as it boots. > for example, the original areacode.gdb is only 12k, but mine has now swollen > to 37k by just opening and closing it without any editing. If it gets too > much, i import it into a new file and it will be again 12k, but then DBview > won't give me subsets. I THINK - open the file, edit one record, you don't have to actually change any data, just re-write one or two letters in any field and then close - it may then do "garbage collection" and shrink the file back down. ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 11:30:18 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: FW: Palmtop & various other items This is a list of items that I still have available, for the 200LX. All items work in the 200LX. Rather than continue to tell you what I don't have, I am listing what I do still have. I will pay standard shipping to the continental United States. Lots of stuff has sold fast, thanks for the bandwidth. 1-Used 200LX-8 meg-2X speed (Thaddeus upgraded, was 1 meg-1X speed) Language: US English Serial Number: SG53600968 Includes: manuals & carry case Condition: repaired right side hinge crack, otherwise good condition Price: $250.00 (Thaddeus sells for $400) 1-HP AC Adapter Model Number: F1011A-ABA Price: $25 (Thaddeus sells for $50) 2-HP Connectivity Cables Model Number: F1015-80002 Price: $20 each (Thaddeus sells for $40) 1-Belkins Serial to Parallel Adapter Model Number: F5F113 Price: $40 each (Thaddeus sells Greenwich for $70, I paid $90 each for these) 1-Cigarette Lighter Adapter for 200LX (charge your LX while traveling) Price: $15 1-PowerBasic v3.50 Includes: PB user guide, PB reference guide, disks & Sam s Learning Basic book Price: $50 (I paid $100 for PB software which is still sold and supported at v3.50 for $100 at: www.powerbasic.com, learning basic book was $40.00) 1-Personal Food Analyst Includes: Manual & PCMCIA card with software on card Price: $7 (Thaddeus sells for $12) 1-SimpleTech 40MB ATA PCMCIA Flash Card Price: $40 each (you don t want to know what I paid for this) Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 09:37:50 -0700 Reply-To: Bob Christopher Sender: HPLX Mailing List From: Bob Christopher Subject: Convert *DB TO DBF Mime-Version: 1.0 Content-Type: text/plain; charset=iso-8859-1 Content-Transfer-Encoding: 8bit Has anyone come across a utility that will convert the LX databases (adb,pdb,mdb,wdb,etc) to dBase dbf format and vice-versa? Bob .......................................................... Bob Christopher Littleton, Colorado USA bob@palmtop.com . HP200LX Palmtop .Submini Cameras. Vintage Mechanicals . ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 08:56:37 -0700 Reply-To: Longden_Loo@CANDLE.COM Sender: HPLX Mailing List From: Longden Loo Subject: Re: LX <--IR-->OB800 MIME-Version: 1.0 Content-type: text/plain; charset=us-ascii > > There are SIR drivers, and I've tried some on the 800CT with no luck. I > > imagine that at the hardware level, the IR devices for which the SIR > > drivers were written (some off-shore notebook) differed from the 800's. > > I tried to track down the hardware specifications without much > luck. Is there a Linux driver (with source) available? What is > the SIR driver you have? I used the Puma driver disks that came with my son's Trogon notebook. That was a long time ago and I'm not even sure he has the disks anymore (or can find them, being the kid he is). - Longden ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 13:24:13 -0400 Reply-To: Ulrich Allen Sender: HPLX Mailing List From: Ulrich Allen Subject: HPLX <-> pcanywhere-host? MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Is there any chance to get a filetransfer to or from a pcanywhere host with the hplx? Has that been ever tried? Uli ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 14:25:12 -0400 Reply-To: Domingo Sender: HPLX Mailing List From: Domingo Subject: Alternative to Int5f MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: 7bit Hi all. Anyone knows of a faster alternative to Int5f? MMLX and Pal Edit look pretty good with it on my Poqet Plus, but it is rather slow with the screen drawing. The screen is CGA and the machine is an xt, if that makes a difference (I think one of the other emulators requires at least EGA). TIA Domingo ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 21:55:16 +0200 Reply-To: Lasse Karlsson Sender: HPLX Mailing List From: Lasse Karlsson Subject: Re: SMS and Post/PDU with Nokia 6210 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Fri, 31 Aug 2001 21:43:51 +0200 (CET) 13h38m46s ago ... On Fri, 31 Aug 2001 08:05:05 +0200, Daniel Hertrich wrote: > You have to adjust the SMSC number in sms.tpl. > It is the SMS center number, i.e. the number you also set in the > telephone as SMS service center. Thanks for your advice. Been there, done that... Here is a piece of the robot trace. It seems like the: SEND AT+CMGS=3D031 fails...? Any ideas? ----------------------------------------- PROCESS file c PROCESS send AT+CMG$c3=3D$it\r SEND AT+CMGS=3D031 PROCESS wait 4 > GOT >AT+CMGS=3D031 >< PROCESS file r sms.pdu PROCESS get FGOT 07916407080007F811000C916437930821F40000AD13F0FA7C0E7A83D6F270BBA1682= 81A8A8602 PROCESS send $it SEND 07916407080007F811000C916437930821F40000AD13F0FA7C0E7A83D6F270BBA1682= 81A8A8602 PROCESS send \032\r SEND ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 22:14:07 +0200 Reply-To: Lasse Karlsson Sender: HPLX Mailing List From: Lasse Karlsson Subject: Re: SMS and Post/PDU with Nokia 6210 MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Fri, 31 Aug 2001 22:10:02 +0200 (CET) The trace I tried to send got truncated by the CTRL Here is a new try -------------------------------- PROCESS file c PROCESS send AT+CMG$c3=3D$it\r SEND AT+CMGS=3D031 PROCESS wait 4 > GOT >AT+CMGS=3D031 >< PROCESS file r sms.pdu PROCESS get FGOT 07916407080007F811....snipped PROCESS send $it SEND 07916407080007F811....snipped PROCESS send \032\r SEND ctrl PROCESS file c PROCESS PROCESS :send_status PROCESS get GOT >07916407080007F811....snipped PROCESS if (begin ERROR) send_error PROCESS if (begin OK) send_ok PROCESS if (!begin +CMG) send_status PROCESS get GOT >< PROCESS if (begin ERROR) send_error PROCESS if (begin OK) send_ok PROCESS if (!begin +CMG) send_status PROCESS get GOT >> < PROCESS if (begin ERROR) send_error PROCESS if (begin OK) send_ok PROCESS if (!begin +CMG) send_status PROCESS get GOT >+CMS ERROR: 38< PROCESS if (begin ERROR) send_error PROCESS if (begin OK) send_ok PROCESS if (!begin +CMG) send_status PRHanging up... OCESS get GOT BEFORE TIMEOUT: >< Freeing rand Freeing c8=3D'c:\bin\wwwlx\' Freeing c9=3D'c:\_dat\wwwlx\sms\' Freeing c3=3D'S' Freeing c4=3D'sending' Freeing c5=3D'SENDING' Freeing n5 Freeing n1 Freeing c1=3D'SMSC: +46708000708 To: +46733980124 puss o kram ' Freeing c6=3D'SMS' Freeing c2=3D'm' Freeing n2 ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 23:05:27 +0200 Reply-To: Daniel Hertrich Sender: HPLX Mailing List From: Daniel Hertrich Subject: Fwd: HP Backup Messages MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Hi friends, I'm sorry!!! "My" idea wasn't actually my idea! I just found a message in my private email inbox, which I haven't read by now, written by David Solinas. He suggested exactly what I have posted about the appts.ini ÝFORTUNECOOKIE¨ idea of notifying me about the backup success. I don't think David minds if I send his message to the list: --- begin of forwarded message --- From: "Solinas, David M." To: "'palmtop@epost.de'" Subject: HP Backup Messages Date: Thu, 16 Aug 2001 09:06:22 -0400 Hi Daniel. In HPLX-L, you wrote: > What I'm looking for is a way to let the palmtop notify me about the > failed backup automatically if I switch it on the next morning. > I think about something like the greeting message of the appointment > book, containint not a palmtop tip, but the message "backup failed last > night". I have my backup script write its results to the appts.ini file. It tells me how many files it copied to the flash card, and when. Right now, my greeting message is: Backup found 8 new data files Wed Aug 15 18:36:03 GMT 2001 I'll send you my script if you like, but it uses the MKS Toolkit for some Unix-like commands (rm, echo, paste, find, touch, date and cat). The idea is that I keep a file called "apptsini.tpl" (meaning template), which has the following lines in it: ÝEMPTYDAY¨ COUNT=1 001=No new or due items today. ÝFORTUNECOOKIE¨ COUNT=1 ; = Ý...¨ ~ Ý...¨ ~ That last line is a commented line that shows the format of the fortune cookie lines -- I took out a bunch of spaces for this Email. The tilde is a line terminator, and you can only have 46 chars per each of the two lines. So there were 46 blanks before each tilde. This line comes with the appts.ini file. Then, my script makes a temp file with the line: 001=Backup found 8new data files~Wed Aug 15 18:36:03 GMT 2001 (no ending tilde, I notice). Finally, I append the temp file to the template file, and write it as c:\_dat\appts.ini, and that's it. Again, let me know if you want the script. It's pretty simple. BTW, have you heard from Chris Lott about the next version of REX2HP? I've mailed him twice w/o a reply, and I don't want to keep bothering him. Dave Solinas --- end of forwarded message --- -- http://www.daniel-hertrich.de/contact ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Sat, 1 Sep 2001 01:21:17 +0000 Reply-To: Russel Brooks Sender: HPLX Mailing List From: Russel Brooks Subject: Re: Alternative to Int5f MIME-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 8bit Domingo wrote: > Hi all. Anyone knows of a faster alternative to Int5f? MMLX and Pal Edit > look pretty good with it on my Poqet Plus, but it is rather slow with the > screen drawing. The screen is CGA and the machine is an xt, if that makes a > difference (I think one of the other emulators requires at least EGA). I don't think it is faster but PALRUN was supposed to replace Int5f (I think). Cheers... Russ ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml ========================================================================= Date: Fri, 31 Aug 2001 22:51:35 -0400 Reply-To: Robert Hocking Sender: HPLX Mailing List From: Robert Hocking Subject: FS: 3 items left This is all I have left: 1-HP Connectivity Cables Model Number: F1015-80002 Price: $20 each (Thaddeus sells for $40) 1-Belkins Serial to Parallel Adapter Model Number: F5F113 Price: $40 each (Thaddeus sells Greenwich for $70, I paid $90 each for these) 1-PowerBasic v3.50 Includes: PB user guide, PB reference guide, disks & Sam s Learning Basic book Price: $50 (I paid $100 for PB software which is still sold and supported at v3.50 for $100 at: www.powerbasic.com, learning basic book was $40.00) Best Regards, Robert Hocking ** HPLX-L LIST Info at http://www.sp.uconn.edu/~mchem1/HPLX.shtml